AKiTiO MyCloud Mini use Hynix
HY5PS1G831CFP-S6, x2.
in NAS 7825 Data Sheet page 16 say: two ranks of 1Gbx16 requires modified software. HY5PS1G831CFP-S6 is 1Gbx8? does not require special software? i hope so.
i also tried Iomega HMCE source. EMCLifeline-GPL-Bellagio.zip not include U-Boot source; EMCLifeline-GPL-Bellagio-patch.zip include U-Boot source for PLX, but not find Stage1 source. so i use DC01 Stage1 + HMCE U-Boot to test 256MB.
$this->bbcode_second_pass_code('', '
Stage-1 Bootloader Wed Mar 7 20:24:56 CST 2012
Attempting to set PLLA to 750MHz ...
plla_ctrl0 : 0x0000000A
plla_ctrl1 : 0x000F0000
plla_ctrl2 : 0x001D01A0
plla_ctrl3 : 0x00000017
PLLA Set
Setup memory, testing
Reading disk 00
Sector : 0x0000009A
Hdr len: 0x00019020
Hdr CRC: 0x4C172C55
OK
Initialising disks
SATA PHY not ready for device 1
Detecting SATA busses:
Bus 0: Found first device OK
Device 0: Model: WDC WD1600BEVT-22ZCT0 Firm: 11.01A11 Ser#: WD-WXEZ07C79076
Type: Hard Disk
Capacity: 131071.9 MB = 127.9 GB (268435455 x 512)
Device 1: not available
Environment successfully read from disk 0 primary image
U-Boot 1.1.2 (Mar 9 2012 - 00:49:16)
U-Boot code: 60D00000 -> 60D19020 BSS: -> 60D1CCB0
RAM Configuration:
Bank #0: 60000000 256 MB
SRAM Configuration:
64KB at 0x50000000
In: serial
Out: serial
Err: serial
Setting Linux mem= boot arg value
IDE read: device 0 block # 288, count 1 ... 1 blocks read: OK
Hit any key to stop autoboot: 0
Loading from IDE device 0, partition 1: Name: hda1
Type: U-Boot
Image Name: Linux-2.6.31.14_SMP_7821
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1934308 Bytes = 1.8 MB
Load Address: 60008000
Entry Point: 60008000
## Booting image at 60500000 ...
Image Name: Linux-2.6.31.14_SMP_7821
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1934308 Bytes = 1.8 MB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux..................................................................................................................... done, booting the kernel.
')
and
$this->bbcode_second_pass_code('', '
PLX>>setenv bootargs 'console=ttyS0,115200 root=/dev/sda5 rootfstype=ext4 mem=256M noinitrd raid=noautodetect'
PLX>>saveenv
Saving Environment to Disk...
wait_no_error() SATA core flagged error
oxnas_sata_outb() Wait for ATA no-error timed-out
Error (no IRQ) dev 0 blk 558: status 0x59
Saving environment to disk 0 primary image failed
')
can't save U-Boot environments.
$this->bbcode_second_pass_code('', '
PLX>>tftpboot 0x60500000 uImage
Wait GMAC to reset
Wait for PHY reset
Ethernet Phy not recognised!
Wait for link to come up.Link up
Wait for auto-negotiation to complete.....
')
can't recognise RTL8211D.
maybe i need compare U-Boot source between DC01 and HMCE, and patch DC01 U-Boot source for test 256MB.