by dannyp » Fri Mar 16, 2012 6:25 pm
here is the output with the drive in the cradle.
To run a command as administrator (user "root"), use "sudo <command>".
See "man sudo_root" for details.
$this->bbcode_second_pass_code('', '
ubuntu@ubuntu:~$ sudo ifconfig eth0:0 10.10.10.5
ubuntu@ubuntu:~$ sudo ifconfig eth0:1 10.10.10.4
ubuntu@ubuntu:~$ sudo ifconfig eth0:2 10.10.10.2
ubuntu@ubuntu:~$ nc -lu 10.10.10.5 6666
U-Boot 2010.09 (Feb 16 2011 - 18:44:23)
UBIT v0.6 by Jeff Doozan and Peter Carmichael
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:fast", error -19
Error reading superblock on volume 'ubi:fast'!
UBIFS not mounted, use ubifs mount to mount volume first!
** Block device usb 0 not supported
** Block device usb 0 not supported
** Invalid boot device **
** Invalid boot device **
** Block device usb 1 not supported
** Block device usb 1 not supported
** Invalid boot device **
** Invalid boot device **
** Block device usb 2 not supported
** Block device usb 2 not supported
** Invalid boot device **
** Invalid boot device **
** Block device usb 3 not supported
** Block device usb 3 not supported
** Invalid boot device **
** Invalid boot device **
Reset IDE: Bus 0: ...OK Bus 1: not available
Device 0: Model: ST33000651AS Firm: CC43 Ser#: 9XK09DJA
Type: Hard Disk
Supports 48-bit addressing
Capacity: 764436.4 MB = 746.5 GB (1565565872 x 512)
Loading file "/boot/uImage" from ide device 0:1 (hda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 0:1 **
Loading file "/uInitrd" from ide device 0:1 (hda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 0:1 **
reading /boot/uImage
** Unable to read "/boot/uImage" from ide 0:1 **
reading /uInitrd
** Unable to read "/uInitrd" from ide 0:1 **
** Bad partition 1 **
** Bad partition 1 **
No Powersaving mode 7F
Error (no IRQ) dev 1 blk 0: status 0x7f
** Can't read from device 1 **
** Unable to use ide 1:1 for fatload **
No Powersaving mode 7F
Error (no IRQ) dev 1 blk 0: status 0x7f
** Can't read from device 1 **
** Unable to use ide 1:1 for fatload **
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:ramdisk", error -19
Error reading superblock on volume 'ubi:ramdisk'!
UBIFS not mounted, use ubifs mount to mount volume first!
Marvell>>
')
Last edited by
WarheadsSE on Fri Mar 16, 2012 8:36 pm, edited 1 time in total.
Reason: CODE TAGS
Goflex Home 3TB Alarm
- SAMBA, MYSQL, SICKBEARD, COUCHPOTATO, HEADPHONES, WEBMIN, SABNZBD.
Goflex Home 2TB Alarm
- SAMBA, SUBSONIC, WEBMIN.
Raspberry PI Model B 512K
- RASPBMC