Pogoplug Cant Boot USB

Discussion about U-Boot and the kernel.

Pogoplug Cant Boot USB

Postby HardyHardwich » Tue May 09, 2017 2:53 pm

After a long time i want to work again with my pogoplug, but its dosnt boot the usb drive.
i tested it with a 4gb and 2 gb stick.

What can i do to bring it back to the default?

Code: Select all
Stage-1 Bootloader XCE_STAGE1: 1.1: Tue Feb  8 01:40:26 PST 2011
Attempting to set PLLA to 700MHz ...
  plla_ctrl0 : 0x0000000A
  plla_ctrl1 : 0x000E0000
  plla_ctrl2 : 0x001C01A0
  plla_ctrl3 : 0x00000016
PLLA Set

Setup memory, testing
Reading NAND, Image 0
  Hdr len: 0x0001C030
  Hdr CRC: 0x39F6D832
 OK


U-Boot 1.1.2 (Jul 29 2010 - 19:36:07)

U-Boot code: 60D00000 -> 60D1C030  BSS: -> 60D21800
RAM Configuration:
        Bank #0: 60000000 128 MB
SRAM Configuration:
        64KB at 0x50000000
NAND:128 MiB
In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value
Hit any key to stop autoboot:  0

Loading from device 0: 128MiB 3,3V 8-bit (offset 0x500000)
   -- Using 1bit ECC style encoding
   Image Name:   Linux-2.6.31.6_SMP_820
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2288744 Bytes =  2.2 MB
   Load Address: 60008000
   Entry Point:  60008000
## Booting image at 60500000 ...
   Image Name:   Linux-2.6.31.6_SMP_820
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2288744 Bytes =  2.2 MB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux.............................................................                                                                                                                               ............................................................................. do                                                                                                                               ne, booting the kernel.
[    0.000000] Linux version 2.6.31.6_SMP_820 (root@hunchback) (gcc version 4.7.                                                                                                                               0 20120505 (prerelease) (GCC) ) #6 SMP Thu Jun 14 19:49:57 CDT 2012
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr                                                                                                                               =00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca                                                                                                                               che
[    0.000000] Machine: Oxsemi NAS
[    0.000000] 1 memory region
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag                                                                                                                               es: 32512
[    0.000000] Kernel command line: root=/dev/sda1 ubi.mtd=2,512 rootfstype=ext3                                                                                                                                console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 rootwai                                                                                                                               t mem=128M poweroutage=yes
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 125240KB available (3904K code, 303K data, 140K init, 0K                                                                                                                                highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:96
[    0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[    0.010000] Console: colour dummy device 80x30
[    0.010000] console [ttyS0] enabled
[    0.020000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
[    0.260000] Security Framework initialized
[    0.260000] Mount-cache hash table entries: 512
[    0.270000] CPU: Testing write buffer coherency: ok
[    0.270000] Calibrating local timer... 350.00MHz.
[    0.340000] CPU1: Booted secondary processor
[    0.440000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
[    0.670000] Brought up 2 CPUs
[    0.680000] SMP: Total of 2 processors activated (558.69 BogoMIPS).
[    0.690000] tmpfs: No value for mount option 'mode'
[    0.690000] devtmpfs: initialized
[    0.700000] NET: Registered protocol family 16
[    0.700000] Number of DMA channels = 4, version = 4
[    0.710000] Reserving a DMA channel for DirectRAID
[    0.710000] Allocating 389 SRAM generic DMA descriptors
[    0.730000] bio: create slab <bio-0> at 0
[    0.740000] SCSI subsystem initialized
[    0.740000] usbcore: registered new interface driver usbfs
[    0.750000] usbcore: registered new interface driver hub
[    0.750000] usbcore: registered new device driver usb
[    0.790000] NET: Registered protocol family 2
[    0.790000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.800000] Switched to NOHz mode on CPU #0
[    0.800000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.800000] Switched to NOHz mode on CPU #1
[    0.810000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.820000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.820000] TCP reno registered
[    0.830000] NET: Registered protocol family 1
[    0.830000] Create fragment cache
[    0.860000] fuse init (API version 7.12)
[    0.860000] msgmni has been set to 244
[    0.870000] alg: No test for stdrng (krng)
[    0.870000] io scheduler noop registered
[    0.870000] io scheduler anticipatory registered
[    0.880000] io scheduler deadline registered
[    0.880000] io scheduler cfq registered (default)
[    0.910000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.920000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[    0.930000] brd: module loaded
[    0.940000] loop: module loaded
[    0.950000] ox820sata: OX820 sata core.
[    0.950000] scsi0 : oxnassata
[    0.950000] scsi1 : oxnassata
[    0.960000] ata1: SATA max UDMA/133 irq 50
[    0.960000] ata2: SATA max UDMA/133 irq 50
[    0.970000] ox820sata: reseting SATA core
[    1.330000] ata1: SATA link down (SStatus 0 SControl 300)
[    1.330000] ox820sata: reseting SATA core
[    1.690000] ata2: SATA link down (SStatus 0 SControl 300)
[    1.690000] tun: Universal TUN/TAP device driver, 1.6
[    1.700000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.700000] NAND: Page read time 40ms
[    1.710000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128                                                                                                                               MiB 3,3V 8-bit)
[    1.720000] Scanning device for bad blocks
[    1.750000] Bad eraseblock 477 at 0x000003ba0000
[    1.800000] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
[    1.800000] 0x000000000000-0x000000e00000 : "boot"
[    1.810000] 0x000000e00000-0x000008000000 : "rootfs"
[    1.810000] UBI: attaching mtd2 to ubi0
[    1.820000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[    1.820000] UBI: logical eraseblock size:    129024 bytes
[    1.830000] UBI: smallest flash I/O unit:    2048
[    1.830000] UBI: sub-page size:              512
[    1.840000] UBI: VID header offset:          512 (aligned 512)
[    1.840000] UBI: data offset:                2048
[    2.250000] UBI: attached mtd2 to ubi0
[    2.260000] UBI: MTD device name:            "rootfs"
[    2.260000] UBI: MTD device size:            114 MiB
[    2.270000] UBI: number of good PEBs:        911
[    2.270000] UBI: number of bad PEBs:         1
[    2.280000] UBI: max. allowed volumes:       128
[    2.280000] UBI: wear-leveling threshold:    4096
[    2.280000] UBI: number of internal volumes: 1
[    2.290000] UBI: number of user volumes:     1
[    2.290000] UBI: available PEBs:             0
[    2.300000] UBI: total number of reserved PEBs: 911
[    2.300000] UBI: number of PEBs reserved for bad PEB handling: 9
[    2.310000] UBI: max/mean erase counter: 2/1
[    2.310000] UBI: image sequence number: 0
[    2.320000] UBI: background thread "ubi_bgt0d" started, PID 306
[    2.320000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.320000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
[    2.320000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus num                                                                                                                               ber 1
[    2.350000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
[    2.370000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
[    2.370000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.380000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=                                                                                                                               1
[    2.380000] usb usb1: Product: OXNAS EHCI Host Controller
[    2.390000] usb usb1: Manufacturer: Linux 2.6.31.6_SMP_820 ehci_hcd
[    2.400000] usb usb1: SerialNumber: usb
[    2.400000] usb usb1: configuration #1 chosen from 1 choice
[    2.410000] hub 1-0:1.0: USB hub found
[    2.410000] hub 1-0:1.0: 2 ports detected
[    2.420000] Initializing USB Mass Storage driver...
[    2.420000] usbcore: registered new interface driver usb-storage
[    2.430000] USB Mass Storage support registered.
[    2.430000] usbcore: registered new interface driver libusual
[    2.440000] mice: PS/2 mouse device common for all mice
[    2.440000] usbcore: registered new interface driver hiddev
[    2.450000] usbcore: registered new interface driver usbhid
[    2.460000] usbhid: v2.6:USB HID core driver
[    2.460000] TCP cubic registered
[    2.460000] NET: Registered protocol family 10
[    2.470000] lo: Disabled Privacy Extensions
[    2.470000] NET: Registered protocol family 17
[    2.480000] RPC: Registered udp transport module.
[    2.480000] RPC: Registered tcp transport module.
[    2.490000] Waiting for root device /dev/sda1...
[    2.730000] usb 1-1: new high speed USB device using oxnas-ehci and address 2
[    2.880000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    2.880000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.890000] usb 1-1: Product: USB2.0 Hub
[    2.900000] usb 1-1: configuration #1 chosen from 1 choice
[    2.900000] hub 1-1:1.0: USB hub found
[    2.910000] hub 1-1:1.0: 4 ports detected
[    3.190000] usb 1-1.4: new high speed USB device using oxnas-ehci and address                                                                                                                                3
[    3.380000] usb 1-1.4: New USB device found, idVendor=090c, idProduct=1000
[    3.390000] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber                                                                                                                               =3
[    3.390000] usb 1-1.4: Product: USB Flash Drive
[    3.400000] usb 1-1.4: Manufacturer: USB 2.0
[    3.400000] usb 1-1.4: SerialNumber: AA00000000000552
[    3.410000] usb 1-1.4: configuration #1 chosen from 1 choice
[    3.410000] scsi2 : SCSI emulation for USB Mass Storage devices
[    9.140000] scsi 2:0:0:0: Direct-Access     USB 2.0  USB Flash Drive  1100 PQ: 0 ANSI: 0 CCS
[    9.150000] sd 2:0:0:0: [sda] 7913472 512-byte logical blocks: (4.05 GB/3.77 GiB)
[    9.160000] sd 2:0:0:0: [sda] Write Protect is off
[    9.170000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    9.180000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    9.180000]  sda: sda1 sda2
[    9.190000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    9.190000] sd 2:0:0:0: [sda] Attached SCSI removable disk
[    9.200000] List of all partitions:
[    9.210000] 1f00          131072 mtdblock0 (driver?)
[    9.210000] 1f01           14336 mtdblock1 (driver?)
[    9.220000] 1f02          116736 mtdblock2 (driver?)
[    9.220000] 0800         3956736 sda driver: sd
[    9.230000]   0801          487424 sda1
[    9.230000]   0802           65536 sda2
[    9.230000] No filesystem could mount root, tried:  ext3
[    9.240000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)
[    9.250000] CPU1: stopping
[    9.250000] [<c00305e4>] (unwind_backtrace+0x0/0xe0) from [<c002b39c>] (do_IPI+0xe8/0x154)
[    9.260000] [<c002b39c>] (do_IPI+0xe8/0x154) from [<c03239d8>] (__irq_svc+0x38/0xc0)
[    9.270000] Exception stack(0xc7843f90 to 0xc7843fd8)
[    9.270000] 3f80:                                     0b6fc704 00000000 c7843fd8 00000000
[    9.280000] 3fa0: c7842000 c7842000 c043d0c4 c041c02c 00000000 410fb025 60022f14 00000000
[    9.290000] 3fc0: 7fffffff c7843fd8 c002c53c c002c540 60000013 ffffffff
[    9.290000] [<c03239d8>] (__irq_svc+0x38/0xc0) from [<c002c540>] (default_idle+0x24/0x28)
[    9.300000] [<c002c540>] (default_idle+0x24/0x28) from [<c002c6f0>] (cpu_idle+0x58/0x94)
[    9.310000] [<c002c6f0>] (cpu_idle+0x58/0x94) from [<60008084>] (0x60008084)
HardyHardwich
 
Posts: 3
Joined: Tue May 09, 2017 11:42 am

Re: Pogoplug Cant Boot USB

Postby WarheadsSE » Tue May 09, 2017 3:31 pm

This is a pogoplug v3, and the kernel for this is very old. This will cause issues with newer libraries.

As for this failure, please note that it appears your root partition is actually -not- ext3 as far as that kernel can tell. Please check the filesystem.
Core Developer
Remember: Arch Linux ARM is entirely community donation supported!
WarheadsSE
Developer
 
Posts: 6730
Joined: Mon Oct 18, 2010 2:12 pm

Re: Pogoplug Cant Boot USB

Postby HardyHardwich » Tue May 09, 2017 6:57 pm

How can i get the ext3 filessystem on the storage?

I only have a win10 system.

EDIT: How can i reinstall a new Version of ArchLinux via Serial Port, whitout starting a running system from the storage?
HardyHardwich
 
Posts: 3
Joined: Tue May 09, 2017 11:42 am

Re: Pogoplug Cant Boot USB

Postby HardyHardwich » Thu May 11, 2017 10:01 pm

I have prepare a new storage with linux on my pc but now i get a new error:

Code: Select all
Stage-1 Bootloader XCE_STAGE1: 1.1: Tue Feb  8 01:40:26 PST 2011
Attempting to set PLLA to 700MHz ...
  plla_ctrl0 : 0x0000000A
  plla_ctrl1 : 0x000E0000
  plla_ctrl2 : 0x001C01A0
  plla_ctrl3 : 0x00000016
PLLA Set

Setup memory, testing
Reading NAND, Image 0
  Hdr len: 0x0001C030
  Hdr CRC: 0x39F6D832
 OK


U-Boot 1.1.2 (Jul 29 2010 - 19:36:07)

U-Boot code: 60D00000 -> 60D1C030  BSS: -> 60D21800
RAM Configuration:
        Bank #0: 60000000 128 MB
SRAM Configuration:
        64KB at 0x50000000
NAND:128 MiB
In:    serial
Out:   serial
Err:   serial
Setting Linux mem= boot arg value
Hit any key to stop autoboot:  0

Loading from device 0: 128MiB 3,3V 8-bit (offset 0x500000)
   -- Using 1bit ECC style encoding
   Image Name:   Linux-2.6.31.6_SMP_820
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2288744 Bytes =  2.2 MB
   Load Address: 60008000
   Entry Point:  60008000
## Booting image at 60500000 ...
   Image Name:   Linux-2.6.31.6_SMP_820
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2288744 Bytes =  2.2 MB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux.............................................................                                                                                     ............................................................................. do                                                                                     ne, booting the kernel.
[    0.000000] Linux version 2.6.31.6_SMP_820 (root@hunchback) (gcc version 4.7.                                                                                     0 20120505 (prerelease) (GCC) ) #6 SMP Thu Jun 14 19:49:57 CDT 2012
[    0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr                                                                                     =00c5387f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca                                                                                     che
[    0.000000] Machine: Oxsemi NAS
[    0.000000] 1 memory region
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag                                                                                     es: 32512
[    0.000000] Kernel command line: root=/dev/sda1 ubi.mtd=2,512 rootfstype=ext3                                                                                      console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 rootwai                                                                                     t mem=128M poweroutage=yes
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 125240KB available (3904K code, 303K data, 140K init, 0K                                                                                      highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:96
[    0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[    0.010000] Console: colour dummy device 80x30
[    0.010000] console [ttyS0] enabled
[    0.020000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
[    0.260000] Security Framework initialized
[    0.260000] Mount-cache hash table entries: 512
[    0.270000] CPU: Testing write buffer coherency: ok
[    0.270000] Calibrating local timer... 350.00MHz.
[    0.340000] CPU1: Booted secondary processor
[    0.440000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
[    0.670000] Brought up 2 CPUs
[    0.680000] SMP: Total of 2 processors activated (558.69 BogoMIPS).
[    0.690000] tmpfs: No value for mount option 'mode'
[    0.690000] devtmpfs: initialized
[    0.700000] NET: Registered protocol family 16
[    0.700000] Number of DMA channels = 4, version = 4
[    0.710000] Reserving a DMA channel for DirectRAID
[    0.710000] Allocating 389 SRAM generic DMA descriptors
[    0.730000] bio: create slab <bio-0> at 0
[    0.740000] SCSI subsystem initialized
[    0.740000] usbcore: registered new interface driver usbfs
[    0.750000] usbcore: registered new interface driver hub
[    0.750000] usbcore: registered new device driver usb
[    0.790000] NET: Registered protocol family 2
[    0.790000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.800000] Switched to NOHz mode on CPU #0
[    0.800000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.800000] Switched to NOHz mode on CPU #1
[    0.810000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.820000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.820000] TCP reno registered
[    0.830000] NET: Registered protocol family 1
[    0.830000] Create fragment cache
[    0.860000] fuse init (API version 7.12)
[    0.860000] msgmni has been set to 244
[    0.870000] alg: No test for stdrng (krng)
[    0.870000] io scheduler noop registered
[    0.870000] io scheduler anticipatory registered
[    0.880000] io scheduler deadline registered
[    0.880000] io scheduler cfq registered (default)
[    0.910000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.910000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[    0.930000] brd: module loaded
[    0.940000] loop: module loaded
[    0.940000] ox820sata: OX820 sata core.
[    0.950000] scsi0 : oxnassata
[    0.950000] scsi1 : oxnassata
[    0.960000] ata1: SATA max UDMA/133 irq 50
[    0.960000] ata2: SATA max UDMA/133 irq 50
[    0.960000] ox820sata: reseting SATA core
[    1.330000] ata1: SATA link down (SStatus 0 SControl 300)
[    1.330000] ox820sata: reseting SATA core
[    1.690000] ata2: SATA link down (SStatus 0 SControl 300)
[    1.690000] tun: Universal TUN/TAP device driver, 1.6
[    1.700000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.700000] NAND: Page read time 40ms
[    1.710000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128                                                                                     MiB 3,3V 8-bit)
[    1.720000] Scanning device for bad blocks
[    1.750000] Bad eraseblock 477 at 0x000003ba0000
[    1.800000] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
[    1.800000] 0x000000000000-0x000000e00000 : "boot"
[    1.810000] 0x000000e00000-0x000008000000 : "rootfs"
[    1.810000] UBI: attaching mtd2 to ubi0
[    1.820000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[    1.820000] UBI: logical eraseblock size:    129024 bytes
[    1.830000] UBI: smallest flash I/O unit:    2048
[    1.830000] UBI: sub-page size:              512
[    1.840000] UBI: VID header offset:          512 (aligned 512)
[    1.840000] UBI: data offset:                2048
[    2.250000] UBI: attached mtd2 to ubi0
[    2.260000] UBI: MTD device name:            "rootfs"
[    2.260000] UBI: MTD device size:            114 MiB
[    2.270000] UBI: number of good PEBs:        911
[    2.270000] UBI: number of bad PEBs:         1
[    2.280000] UBI: max. allowed volumes:       128
[    2.280000] UBI: wear-leveling threshold:    4096
[    2.290000] UBI: number of internal volumes: 1
[    2.290000] UBI: number of user volumes:     1
[    2.290000] UBI: available PEBs:             0
[    2.300000] UBI: total number of reserved PEBs: 911
[    2.300000] UBI: number of PEBs reserved for bad PEB handling: 9
[    2.310000] UBI: max/mean erase counter: 2/1
[    2.310000] UBI: image sequence number: 0
[    2.320000] UBI: background thread "ubi_bgt0d" started, PID 306
[    2.320000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.320000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
[    2.320000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus num                                                                                     ber 1
[    2.350000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
[    2.370000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
[    2.370000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.380000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=                                                                                     1
[    2.380000] usb usb1: Product: OXNAS EHCI Host Controller
[    2.390000] usb usb1: Manufacturer: Linux 2.6.31.6_SMP_820 ehci_hcd
[    2.400000] usb usb1: SerialNumber: usb
[    2.400000] usb usb1: configuration #1 chosen from 1 choice
[    2.410000] hub 1-0:1.0: USB hub found
[    2.410000] hub 1-0:1.0: 2 ports detected
[    2.420000] Initializing USB Mass Storage driver...
[    2.420000] usbcore: registered new interface driver usb-storage
[    2.430000] USB Mass Storage support registered.
[    2.430000] usbcore: registered new interface driver libusual
[    2.440000] mice: PS/2 mouse device common for all mice
[    2.440000] usbcore: registered new interface driver hiddev
[    2.450000] usbcore: registered new interface driver usbhid
[    2.460000] usbhid: v2.6:USB HID core driver
[    2.460000] TCP cubic registered
[    2.460000] NET: Registered protocol family 10
[    2.470000] lo: Disabled Privacy Extensions
[    2.470000] NET: Registered protocol family 17
[    2.480000] RPC: Registered udp transport module.
[    2.480000] RPC: Registered tcp transport module.
[    2.490000] Waiting for root device /dev/sda1...
[    2.730000] usb 1-1: new high speed USB device using oxnas-ehci and address 2
[    2.880000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    2.880000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.890000] usb 1-1: Product: USB2.0 Hub
[    2.900000] usb 1-1: configuration #1 chosen from 1 choice
[    2.900000] hub 1-1:1.0: USB hub found
[    2.910000] hub 1-1:1.0: 4 ports detected
[    3.190000] usb 1-1.4: new high speed USB device using oxnas-ehci and address                                                                                      3
[    3.380000] usb 1-1.4: New USB device found, idVendor=090c, idProduct=1000
[    3.390000] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber                                                                                     =3
[    3.390000] usb 1-1.4: Product: USB Flash Drive
[    3.400000] usb 1-1.4: Manufacturer: USB 2.0
[    3.400000] usb 1-1.4: SerialNumber: AA00000000000552
[    3.410000] usb 1-1.4: configuration #1 chosen from 1 choice
[    3.410000] scsi2 : SCSI emulation for USB Mass Storage devices
[    8.710000] scsi 2:0:0:0: Direct-Access     USB 2.0  USB Flash Drive  1100 PQ: 0 ANSI: 0 CCS
[    8.720000] sd 2:0:0:0: [sda] 7913472 512-byte logical blocks: (4.05 GB/3.77 GiB)
[    8.730000] sd 2:0:0:0: [sda] Write Protect is off
[    8.730000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    8.740000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    8.750000]  sda: sda1
[    8.750000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    8.760000] sd 2:0:0:0: [sda] Attached SCSI removable disk
[    8.770000] kjournald starting.  Commit interval 5 seconds
[    8.780000] EXT3 FS on sda1, internal journal
[    8.780000] EXT3-fs: mounted filesystem with writeback data mode.
[    8.790000] VFS: Mounted root (ext3 filesystem) on device 8:1.
[    8.800000] devtmpfs: mounted
[    8.800000] Freeing init memory: 140K
FATAL: kernel too old
[    8.860000] Kernel panic - not syncing: Attempted to kill init!
[    8.860000] CPU1: stopping
[    8.860000] [<c00305e4>] (unwind_backtrace+0x0/0xe0) from [<c002b39c>] (do_IPI+0xe8/0x154)
[    8.870000] [<c002b39c>] (do_IPI+0xe8/0x154) from [<c03239d8>] (__irq_svc+0x38/0xc0)
[    8.880000] Exception stack(0xc7843f90 to 0xc7843fd8)
[    8.880000] 3f80:                                     3280f697 00000000 c7843fd8 00000000
[    8.890000] 3fa0: c7842000 c7842000 c043d0c4 c041c02c 00000000 410fb025 60022f14 00000000
[    8.900000] 3fc0: 7fffffff c7843fd8 c002c53c c002c540 60000013 ffffffff
[    8.910000] [<c03239d8>] (__irq_svc+0x38/0xc0) from [<c002c540>] (default_idle+0x24/0x28)
[    8.920000] [<c002c540>] (default_idle+0x24/0x28) from [<c002c6f0>] (cpu_idle+0x58/0x94)
[    8.930000] [<c002c6f0>] (cpu_idle+0x58/0x94) from [<60008084>] (0x60008084)

HardyHardwich
 
Posts: 3
Joined: Tue May 09, 2017 11:42 am


Return to U-Boot/Kernel

Who is online

Users browsing this forum: No registered users and 1 guest