After a long time i want to work again with my pogoplug, but its dosnt boot the usb drive.
i tested it with a 4gb and 2 gb stick.
What can i do to bring it back to the default?
$this->bbcode_second_pass_code('', 'Stage-1 Bootloader XCE_STAGE1: 1.1: Tue Feb 8 01:40:26 PST 2011
Attempting to set PLLA to 700MHz ...
plla_ctrl0 : 0x0000000A
plla_ctrl1 : 0x000E0000
plla_ctrl2 : 0x001C01A0
plla_ctrl3 : 0x00000016
PLLA Set
Setup memory, testing
Reading NAND, Image 0
Hdr len: 0x0001C030
Hdr CRC: 0x39F6D832
OK
U-Boot 1.1.2 (Jul 29 2010 - 19:36:07)
U-Boot code: 60D00000 -> 60D1C030 BSS: -> 60D21800
RAM Configuration:
Bank #0: 60000000 128 MB
SRAM Configuration:
64KB at 0x50000000
NAND:128 MiB
In: serial
Out: serial
Err: serial
Setting Linux mem= boot arg value
Hit any key to stop autoboot: 0
Loading from device 0: 128MiB 3,3V 8-bit (offset 0x500000)
-- Using 1bit ECC style encoding
Image Name: Linux-2.6.31.6_SMP_820
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2288744 Bytes = 2.2 MB
Load Address: 60008000
Entry Point: 60008000
## Booting image at 60500000 ...
Image Name: Linux-2.6.31.6_SMP_820
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2288744 Bytes = 2.2 MB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux............................................................. ............................................................................. do ne, booting the kernel.
[ 0.000000] Linux version 2.6.31.6_SMP_820 (root@hunchback) (gcc version 4.7. 0 20120505 (prerelease) (GCC) ) #6 SMP Thu Jun 14 19:49:57 CDT 2012
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr =00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca che
[ 0.000000] Machine: Oxsemi NAS
[ 0.000000] 1 memory region
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32512
[ 0.000000] Kernel command line: root=/dev/sda1 ubi.mtd=2,512 rootfstype=ext3 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 rootwai t mem=128M poweroutage=yes
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 125240KB available (3904K code, 303K data, 140K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:96
[ 0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[ 0.010000] Console: colour dummy device 80x30
[ 0.010000] console [ttyS0] enabled
[ 0.020000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
[ 0.260000] Security Framework initialized
[ 0.260000] Mount-cache hash table entries: 512
[ 0.270000] CPU: Testing write buffer coherency: ok
[ 0.270000] Calibrating local timer... 350.00MHz.
[ 0.340000] CPU1: Booted secondary processor
[ 0.440000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
[ 0.670000] Brought up 2 CPUs
[ 0.680000] SMP: Total of 2 processors activated (558.69 BogoMIPS).
[ 0.690000] tmpfs: No value for mount option 'mode'
[ 0.690000] devtmpfs: initialized
[ 0.700000] NET: Registered protocol family 16
[ 0.700000] Number of DMA channels = 4, version = 4
[ 0.710000] Reserving a DMA channel for DirectRAID
[ 0.710000] Allocating 389 SRAM generic DMA descriptors
[ 0.730000] bio: create slab <bio-0> at 0
[ 0.740000] SCSI subsystem initialized
[ 0.740000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.790000] NET: Registered protocol family 2
[ 0.790000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.800000] Switched to NOHz mode on CPU #0
[ 0.800000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.800000] Switched to NOHz mode on CPU #1
[ 0.810000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.820000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.820000] TCP reno registered
[ 0.830000] NET: Registered protocol family 1
[ 0.830000] Create fragment cache
[ 0.860000] fuse init (API version 7.12)
[ 0.860000] msgmni has been set to 244
[ 0.870000] alg: No test for stdrng (krng)
[ 0.870000] io scheduler noop registered
[ 0.870000] io scheduler anticipatory registered
[ 0.880000] io scheduler deadline registered
[ 0.880000] io scheduler cfq registered (default)
[ 0.910000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.920000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[ 0.930000] brd: module loaded
[ 0.940000] loop: module loaded
[ 0.950000] ox820sata: OX820 sata core.
[ 0.950000] scsi0 : oxnassata
[ 0.950000] scsi1 : oxnassata
[ 0.960000] ata1: SATA max UDMA/133 irq 50
[ 0.960000] ata2: SATA max UDMA/133 irq 50
[ 0.970000] ox820sata: reseting SATA core
[ 1.330000] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.330000] ox820sata: reseting SATA core
[ 1.690000] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.690000] tun: Universal TUN/TAP device driver, 1.6
[ 1.700000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.700000] NAND: Page read time 40ms
[ 1.710000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128 MiB 3,3V 8-bit)
[ 1.720000] Scanning device for bad blocks
[ 1.750000] Bad eraseblock 477 at 0x000003ba0000
[ 1.800000] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
[ 1.800000] 0x000000000000-0x000000e00000 : "boot"
[ 1.810000] 0x000000e00000-0x000008000000 : "rootfs"
[ 1.810000] UBI: attaching mtd2 to ubi0
[ 1.820000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 1.820000] UBI: logical eraseblock size: 129024 bytes
[ 1.830000] UBI: smallest flash I/O unit: 2048
[ 1.830000] UBI: sub-page size: 512
[ 1.840000] UBI: VID header offset: 512 (aligned 512)
[ 1.840000] UBI: data offset: 2048
[ 2.250000] UBI: attached mtd2 to ubi0
[ 2.260000] UBI: MTD device name: "rootfs"
[ 2.260000] UBI: MTD device size: 114 MiB
[ 2.270000] UBI: number of good PEBs: 911
[ 2.270000] UBI: number of bad PEBs: 1
[ 2.280000] UBI: max. allowed volumes: 128
[ 2.280000] UBI: wear-leveling threshold: 4096
[ 2.280000] UBI: number of internal volumes: 1
[ 2.290000] UBI: number of user volumes: 1
[ 2.290000] UBI: available PEBs: 0
[ 2.300000] UBI: total number of reserved PEBs: 911
[ 2.300000] UBI: number of PEBs reserved for bad PEB handling: 9
[ 2.310000] UBI: max/mean erase counter: 2/1
[ 2.310000] UBI: image sequence number: 0
[ 2.320000] UBI: background thread "ubi_bgt0d" started, PID 306
[ 2.320000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.320000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
[ 2.320000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus num ber 1
[ 2.350000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
[ 2.370000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
[ 2.370000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.380000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 2.380000] usb usb1: Product: OXNAS EHCI Host Controller
[ 2.390000] usb usb1: Manufacturer: Linux 2.6.31.6_SMP_820 ehci_hcd
[ 2.400000] usb usb1: SerialNumber: usb
[ 2.400000] usb usb1: configuration #1 chosen from 1 choice
[ 2.410000] hub 1-0:1.0: USB hub found
[ 2.410000] hub 1-0:1.0: 2 ports detected
[ 2.420000] Initializing USB Mass Storage driver...
[ 2.420000] usbcore: registered new interface driver usb-storage
[ 2.430000] USB Mass Storage support registered.
[ 2.430000] usbcore: registered new interface driver libusual
[ 2.440000] mice: PS/2 mouse device common for all mice
[ 2.440000] usbcore: registered new interface driver hiddev
[ 2.450000] usbcore: registered new interface driver usbhid
[ 2.460000] usbhid: v2.6:USB HID core driver
[ 2.460000] TCP cubic registered
[ 2.460000] NET: Registered protocol family 10
[ 2.470000] lo: Disabled Privacy Extensions
[ 2.470000] NET: Registered protocol family 17
[ 2.480000] RPC: Registered udp transport module.
[ 2.480000] RPC: Registered tcp transport module.
[ 2.490000] Waiting for root device /dev/sda1...
[ 2.730000] usb 1-1: new high speed USB device using oxnas-ehci and address 2
[ 2.880000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 2.880000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.890000] usb 1-1: Product: USB2.0 Hub
[ 2.900000] usb 1-1: configuration #1 chosen from 1 choice
[ 2.900000] hub 1-1:1.0: USB hub found
[ 2.910000] hub 1-1:1.0: 4 ports detected
[ 3.190000] usb 1-1.4: new high speed USB device using oxnas-ehci and address 3
[ 3.380000] usb 1-1.4: New USB device found, idVendor=090c, idProduct=1000
[ 3.390000] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber =3
[ 3.390000] usb 1-1.4: Product: USB Flash Drive
[ 3.400000] usb 1-1.4: Manufacturer: USB 2.0
[ 3.400000] usb 1-1.4: SerialNumber: AA00000000000552
[ 3.410000] usb 1-1.4: configuration #1 chosen from 1 choice
[ 3.410000] scsi2 : SCSI emulation for USB Mass Storage devices
[ 9.140000] scsi 2:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 0 CCS
[ 9.150000] sd 2:0:0:0: [sda] 7913472 512-byte logical blocks: (4.05 GB/3.77 GiB)
[ 9.160000] sd 2:0:0:0: [sda] Write Protect is off
[ 9.170000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 9.180000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 9.180000] sda: sda1 sda2
[ 9.190000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 9.190000] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 9.200000] List of all partitions:
[ 9.210000] 1f00 131072 mtdblock0 (driver?)
[ 9.210000] 1f01 14336 mtdblock1 (driver?)
[ 9.220000] 1f02 116736 mtdblock2 (driver?)
[ 9.220000] 0800 3956736 sda driver: sd
[ 9.230000] 0801 487424 sda1
[ 9.230000] 0802 65536 sda2
[ 9.230000] No filesystem could mount root, tried: ext3
[ 9.240000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)
[ 9.250000] CPU1: stopping
[ 9.250000] [<c00305e4>] (unwind_backtrace+0x0/0xe0) from [<c002b39c>] (do_IPI+0xe8/0x154)
[ 9.260000] [<c002b39c>] (do_IPI+0xe8/0x154) from [<c03239d8>] (__irq_svc+0x38/0xc0)
[ 9.270000] Exception stack(0xc7843f90 to 0xc7843fd8)
[ 9.270000] 3f80: 0b6fc704 00000000 c7843fd8 00000000
[ 9.280000] 3fa0: c7842000 c7842000 c043d0c4 c041c02c 00000000 410fb025 60022f14 00000000
[ 9.290000] 3fc0: 7fffffff c7843fd8 c002c53c c002c540 60000013 ffffffff
[ 9.290000] [<c03239d8>] (__irq_svc+0x38/0xc0) from [<c002c540>] (default_idle+0x24/0x28)
[ 9.300000] [<c002c540>] (default_idle+0x24/0x28) from [<c002c6f0>] (cpu_idle+0x58/0x94)
[ 9.310000] [<c002c6f0>] (cpu_idle+0x58/0x94) from [<60008084>] (0x60008084)')