by loicPi » Wed Mar 20, 2013 10:58 pm
I have now the output of the printenv command. It don't seem to boot on the usb key anymore. Someome to help me ?
$this->bbcode_second_pass_code('', '
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootcmd=nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000
bootdelay=2
baudrate=115200
loads_echo=0
eth1addr=00:19:CB:00:51:82
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=DD01
PRODUCT_NAME=NSA-320
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=ZyXEL Communications Corp.
run_diag=yes
ethaddr=FC:F5:28:30:0C:B9
arcNumber=3956
bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/sda2 ro rootwait loglevel=8
bootcmd_linux=setenv bootargs $(bootargs_linux); ide reset; ext2load ide 0:1 $(loadaddr) /uImage; bootm $(loadaddr)
bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr)
to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset
to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
mainlineLinux=yes
CASset=min
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
ethprime=egiga1
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::orion:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
disaMvPnp=no
ethmtu=1500
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
hddPowerCtrl=no
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
enaAutoRecovery=yes
kernel_addr=0xc80000
pcieTune=no
ethact=egiga1
Environment size: 2465/131068 bytes
NSA320>>
')