First sorry for my english, i'm french and my english...
...is bad. My raspberry is running on 3.6.11-10-ARCH+ and i try to enable de watchdog module but when i have this problem:
$this->bbcode_second_pass_code('', '[zangdar64@archpi ~]$ sudo modprobe bcm2708_wdog
modprobe: ERROR: could not insert 'bcm2708_wdog': Unknown symbol in module, or unknown parameter (see dmesg)
')
I have seen my dmesg but i nothing talk about the watchdog:
$this->bbcode_second_pass_code('', '[zangdar64@archpi ~]$ dmesg | grep bcm
[ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1184 bcm2708_fb.fbheight=624 bcm2708.boardrev=0x2 bcm2708.serial=0x1bd60c0b smsc95xx.macaddr=B8:27:EB:D6:0C:0B sdhci-bcm2708.emmc_clock_freq=100000000 vc-cma-mem=0/0x5c00000@0x9000000 mem=0x8000000@0x0 mem=0x5c00000@0x9000000 vc_mem.mem_base=0xec00000 vc_mem.mem_size=0x10000000 smsc95xx.turbo_mode=N dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=noop rootwait
[ 0.391102] bcm2708.uart_clock = 0
[ 0.392753] bcm2708_vcio: mailbox at f200b880
[ 0.392840] bcm_power: Broadcom power driver
[ 0.392858] bcm_power_open() -> 0
[ 0.392868] bcm_power_request(0, 8)
[ 0.893545] bcm_mailbox_read -> 00000080, 0
[ 0.893561] bcm_power_request -> 0
[ 1.642801] bcm2708_dma: DMA manager at f2007000
[ 1.642937] bcm2708_gpio: bcm2708_gpio_probe c07a0118
[ 2.283473] dwc_otg bcm2708_usb: DWC OTG Controller
[ 2.283544] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
[ 2.283610] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
[ 2.283921] usb usb1: SerialNumber: bcm2708_usb
[ 2.290165] bcm2835-cpufreq: min=700000 max=700000 cur=700000
[ 2.290273] bcm2835-cpufreq: switching to governor ondemand
[ 2.290289] bcm2835-cpufreq: switching to governor ondemand
[ 3.302356] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:d6:0c:0b
[ 3.743154] input: Western Digital My Book as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/1-1.2:1.1/input/input0
[ 3.743820] hid-generic 0003:1058:1102.0001: input,hidraw0: USB HID v1.11 Device [Western Digital My Book] on usb-bcm2708_usb-1.2/input1
[ 4.206285] bcm2835 ALSA card created!
[ 4.206895] bcm2835 ALSA chip created!
[ 4.207133] bcm2835 ALSA chip created!
[ 4.216231] bcm2835 ALSA chip created!
[ 4.216470] bcm2835 ALSA chip created!
[ 4.217217] bcm2835 ALSA chip created!
[ 4.219166] bcm2835 ALSA chip created!
[ 4.220265] bcm2835 ALSA chip created!
[ 4.220936] systemd-modules-load[60]: Inserted module 'snd_bcm2835'
[ 5.194996] bcm2708_i2c bcm2708_i2c.0: BSC0 Controller at 0x20205000 (irq 79) (baudrate 100k)
[ 5.214926] bcm2708_i2c bcm2708_i2c.1: BSC1 Controller at 0x20804000 (irq 79) (baudrate 100k)
[ 5.228171] bcm2708_spi bcm2708_spi.0: master is unqueued, this is deprecated
[ 5.228438] bcm2708_spi bcm2708_spi.0: SPI Controller at 0x20204000 (irq 80)
')
Somebody know this problem?