CuBox-i: no boot with kernel 4.9.8-1

This forum is for supported devices using an ARMv7 Freescale SoC.

CuBox-i: no boot with kernel 4.9.8-1

Postby Oleg » Sun Jan 22, 2017 8:27 pm

Some time ago I have updated to kernel 4.9.1-1 and CuBox-i2ex and Cubox-4x4 were unable to boot.

Today I have chroot'd and updated to kernel 4.9.5-1 but still unable to boot. Bootlog is attached below:

Code: Select all
U-Boot SPL 2013.10-rc4 (Nov 05 2015 - 12:59:56)
Boot Device: SD1
spl: error reading image u-boot.img, err - -1
Load image from RAW...


U-Boot 2013.10-rc4 (Nov 05 2015 - 12:59:56)

CPU:   Freescale i.MX6Q rev1.5 at 792 MHz
Reset cause: POR
Board: MX6-CuBox-i
DRAM:  1 GiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0
mmc0 is current device
** File not found /boot.scr **
** File not found /uEnv.txt **
** File not found /zImage **
** File not found /uImage **
** File not found /boot/boot.scr **
211 bytes read in 53 ms (2.9 KiB/s)
Importing environment from mmc0 ...
5650424 bytes read in 316 ms (17.1 MiB/s)
Booting from mmc ...
** File not found /boot/initramfs-linux.img **
Loaded initramfs-linux.img
** File not found /boot/imx6q-cubox-i.dtb **
48226 bytes read in 2138 ms (21.5 KiB/s)
Loaded imx6q-cubox-i.dtb
Booting zImage
Kernel image @ 0x10800000 [ 0x000000 - 0x5637f8 ]
## Flattened Device Tree blob at 18000000
   Booting using the fdt blob at 0x18000000
   Using Device Tree in place at 18000000, end 1800ec61

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.5-1-ARCH (builduser@leming) (gcc version 6.3.1 20170109 (GCC) ) #1 SMP Sat Jan 21 22:59:18 MST 2017
[    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt:Machine model: SolidRun Cubox-i Dual/Quad
[    0.000000] cma: Reserved 48 MiB at 0x4d000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] percpu: Embedded 14 pages/cpu @ef6bc000 s26828 r8192 d22324 u57344
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260416
[    0.000000] Kernel command line: root=/dev/mmcblk0p1 rootwait rw console=tty1 console=ttymxc0,115200 consoleblank=0 video=mxcfb0:dev=hdmi,1280x720M@60,if=RGB24,bpp=16 dmfc=3 ahci_imx.hotplug=1 pci=nomsi loop.max_part=15
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 964368K/1048576K available (11264K kernel code, 946K rwdata, 4528K rodata, 1024K init, 840K bss, 35056K reserved, 49152K cma-reserved, 212992K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0c00000   (12256 kB)
[    0.000000]       .init : 0xc1100000 - 0xc1200000   (1024 kB)
[    0.000000]       .data : 0xc1200000 - 0xc12ec8a8   ( 947 kB)
[    0.000000]        .bss : 0xc12ee000 - 0xc13c01f8   ( 841 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]    Build-time adjustment of leaf fanout to 32.
[    0.000000]    RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] L2C-310 errata 752271 769419 enabled
[    0.000000] L2C-310 enabling early BRESP for Cortex-A9
[    0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[    0.000000] L2C-310 ID prefetch enabled, offset 16 lines
[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB
[    0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001
[    0.000000] Switching to timer-based delay loop, resolution 333ns
[    0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
[    0.000023] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
[    0.002201] Console: colour dummy device 80x30
[    0.002673] console [tty1] enabled
[    0.002719] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
[    0.002756] pid_max: default: 32768 minimum: 301
[    0.003023] Security Framework initialized
[    0.003225] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.003254] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.004030] CPU: Testing write buffer coherency: ok
[    0.004338] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.004410] Setting up static identity map for 0x10100000 - 0x10100098
[    0.008441] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.008536] Brought up 2 CPUs
[    0.008583] SMP: Total of 2 processors activated (12.00 BogoMIPS).
[    0.008604] CPU: All CPU(s) started in SVC mode.
[    0.009520] devtmpfs: initialized
[    0.020830] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.021207] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.023721] xor: measuring software checksum speed
[    0.119382]    arm4regs  :  1234.000 MB/sec
[    0.219383]    8regs     :   951.200 MB/sec
[    0.319376]    32regs    :  1028.000 MB/sec
[    0.419380]    neon      :   900.800 MB/sec
[    0.419403] xor: using function: arm4regs (1234.000 MB/sec)
[    0.419509] pinctrl core: initialized pinctrl subsystem
[    0.421083] NET: Registered protocol family 16
[    0.423428] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.459391] cpuidle: using governor menu
[    0.460282] CPU identified as i.MX6Q, silicon rev 1.5
[    0.480049] No ATAGs?
[    0.480084] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.480124] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.481791] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[    0.482955] Serial: AMBA PL011 UART driver
[    0.699536] raid6: int32x1  gen()   106 MB/s
[    0.869438] raid6: int32x1  xor()   147 MB/s
[    1.039556] raid6: int32x2  gen()   165 MB/s
[    1.209493] raid6: int32x2  xor()   167 MB/s
[    1.379700] raid6: int32x4  gen()   193 MB/s
[    1.549557] raid6: int32x4  xor()   165 MB/s
[    1.719481] raid6: int32x8  gen()   215 MB/s
[    1.889429] raid6: int32x8  xor()   153 MB/s
[    2.059435] raid6: neonx1   gen()   616 MB/s
[    2.229385] raid6: neonx1   xor()   452 MB/s
[    2.399424] raid6: neonx2   gen()   658 MB/s
[    2.569403] raid6: neonx2   xor()   577 MB/s
[    2.739409] raid6: neonx4   gen()   660 MB/s
[    2.909432] raid6: neonx4   xor()   525 MB/s
[    3.079407] raid6: neonx8   gen()   494 MB/s
[    3.249409] raid6: neonx8   xor()   446 MB/s
[    3.249436] raid6: using algorithm neonx4 gen() 660 MB/s
[    3.249453] raid6: .... xor() 525 MB/s, rmw enabled
[    3.249470] raid6: using intx1 recovery algorithm
[    3.263436] mxs-dma 110000.dma-apbh: initialized
[    3.269651] vgaarb: loaded
[    3.270415] SCSI subsystem initialized
[    3.270861] usbcore: registered new interface driver usbfs
[    3.270943] usbcore: registered new interface driver hub
[    3.271043] usbcore: registered new device driver usb
[    3.272220] i2c i2c-1: IMX I2C adapter registered
[    3.272259] i2c i2c-1: can't use DMA, using PIO instead.
[    3.272786] i2c i2c-2: IMX I2C adapter registered
[    3.272821] i2c i2c-2: can't use DMA, using PIO instead.
[    3.273722] media: Linux media interface: v0.10
[    3.273788] Linux video capture interface: v2.00
[    3.273870] pps_core: LinuxPPS API ver. 1 registered
[    3.273893] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    3.273937] PTP clock support registered
[    3.273982] EDAC MC: Ver: 3.0.0
[    3.274971] Advanced Linux Sound Architecture Driver Initialized.
[    3.275546] NetLabel: Initializing
[    3.275570] NetLabel:  domain hash size = 128
[    3.275585] NetLabel:  protocols = UNLABELED CIPSOv4
[    3.275650] NetLabel:  unlabeled traffic allowed by default
[    3.276103] clocksource: Switched to clocksource mxc_timer1
[    3.276291] VFS: Disk quotas dquot_6.6.0
[    3.276369] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    3.287076] NET: Registered protocol family 2
[    3.287710] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    3.287813] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    3.287949] TCP: Hash tables configured (established 8192 bind 8192)
[    3.288034] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    3.288092] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    3.288283] NET: Registered protocol family 1
[    3.288775] RPC: Registered named UNIX socket transport module.
[    3.288805] RPC: Registered udp transport module.
[    3.288823] RPC: Registered tcp transport module.
[    3.288841] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    3.289289] Unpacking initramfs...
[    3.289324] Initramfs unpacking failed: junk in compressed archive
[    3.294012] Freeing initrd memory: 5520K (c5100000 - c5664000)
[    3.294490] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[    3.296493] futex hash table entries: 512 (order: 3, 32768 bytes)
[    3.297406] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    3.303211] zbud: loaded
[    3.305797] NFS: Registering the id_resolver key type
[    3.305847] Key type id_resolver registered
[    3.305869] Key type id_legacy registered
[    3.305897] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    3.311817] Key type asymmetric registered
[    3.311900] bounce: pool size: 64 pages
[    3.312097] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    3.312237] io scheduler noop registered
[    3.312261] io scheduler deadline registered
[    3.312453] io scheduler cfq registered (default)
[    3.327809] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[    3.327860] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[    3.335223] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[    3.338021] Serial: AMBA driver
[    3.338785] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, base_baud = 5000000) is a IMX
[    4.174782] console [ttymxc0] enabled
[    4.179400] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 66, base_baud = 5000000) is a IMX
[    4.189325] [drm] Initialized
[    4.200439] loop: module loaded
[    4.205346] Loading iSCSI transport class v2.0-870.
[    4.210676] iscsi: registered transport (tcp)
[    4.216016] ahci-imx 2200000.sata: fsl,transmit-level-mV value 1104, using 00000044
[    4.223746] ahci-imx 2200000.sata: fsl,transmit-boost-mdB value 0, using 00000000
[    4.231277] ahci-imx 2200000.sata: fsl,transmit-atten-16ths value 9, using 00002000
[    4.238979] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000
[    4.249519] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled
[    4.256553] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    4.265370] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
[    4.275714] scsi host0: ahci-imx
[    4.279318] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 69
[    4.291423] libphy: Fixed MDIO Bus: probed
[    4.297035] 2188000.ethernet supply phy not found, using dummy regulator
[    4.307334] pps pps0: new PPS source ptp0
[    4.315797] libphy: fec_enet_mii_bus: probed
[    4.320698] fec 2188000.ethernet eth0: registered PHC device 0
[    4.329502] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.336059] ehci-pci: EHCI PCI platform driver
[    4.340591] ehci-platform: EHCI generic platform driver
[    4.346059] ehci-mxc: Freescale On-Chip EHCI Host driver
[    4.351512] ehci-omap: OMAP-EHCI Host Controller driver
[    4.356928] ehci-orion: EHCI orion driver
[    4.361102] ehci-exynos: EHCI EXYNOS driver
[    4.365464] tegra-ehci: Tegra EHCI driver
[    4.369686] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.375906] ohci-pci: OHCI PCI platform driver
[    4.380436] ohci-platform: OHCI generic platform driver
[    4.385859] ohci-exynos: OHCI EXYNOS driver
[    4.390257] ohci-omap3: OHCI OMAP3 driver
[    4.394863] usbcore: registered new interface driver uas
[    4.400296] usbcore: registered new interface driver usb-storage
[    4.406386] usbcore: registered new interface driver ums-cypress
[    4.412447] usbcore: registered new interface driver ums_eneub6250
[    4.418707] usbcore: registered new interface driver ums-freecom
[    4.424765] usbcore: registered new interface driver ums-isd200
[    4.430757] usbcore: registered new interface driver ums-usbat
[    4.446153] ci_hdrc ci_hdrc.0: EHCI Host Controller
[    4.447520] ci_hdrc ci_hdrc.1: EHCI Host Controller
[    4.447557] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[    4.463046] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2
[    4.476132] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[    4.481726] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.488569] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.495822] usb usb1: Product: EHCI Host Controller
[    4.500739] usb usb1: Manufacturer: Linux 4.9.5-1-ARCH ehci_hcd
[    4.506147] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[    4.512105] usb usb1: SerialNumber: ci_hdrc.1
[    4.517137] hub 1-0:1.0: USB hub found
[    4.520953] hub 1-0:1.0: 1 port detected
[    4.525415] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    4.532280] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.539554] usb usb2: Product: EHCI Host Controller
[    4.544451] usb usb2: Manufacturer: Linux 4.9.5-1-ARCH ehci_hcd
[    4.550408] usb usb2: SerialNumber: ci_hdrc.0
[    4.554960] rtc-pcf8523 2-0068: rtc core: registered rtc-pcf8523 as rtc0
[    4.555467] hub 2-0:1.0: USB hub found
[    4.555500] hub 2-0:1.0: 1 port detected
[    4.570698] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
[    4.580170] i2c /dev entries driver
[    4.591870] sdhci: Secure Digital Host Controller Interface driver
[    4.598098] sdhci: Copyright(c) Pierre Ossman
[    4.603610] Synopsys Designware Multimedia Card Interface Driver
[    4.610513] VUB300 Driver rom wait states = 1C irqpoll timeout = 0400[    4.617137] usbcore: registered new interface driver vub300
[    4.620757] ata1: SATA link down (SStatus 0 SControl 300)
[    4.628778] usbcore: registered new interface driver ushc
[    4.634635] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.641215] sdhci-esdhc-imx 2190000.usdhc: allocated mmc-pwrseq
[    4.926133] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[    4.935852] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state, work on normal mode
[    4.945099] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO
[    5.026277] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
[    5.035445] ledtrig-cpu: registered to indicate activity on CPUs
[    5.041822] hidraw: raw HID events driver (C) Jiri Kosina
[    5.053719] usbcore: registered new interface driver usbhid
[    5.059356] usbhid: USB HID core driver
[    5.066336] ashmem: initialized
[    5.074633] NET: Registered protocol family 10
[    5.080171] mip6: Mobile IPv6
[    5.083171] NET: Registered protocol family 17
[    5.087758] Key type dns_resolver registered
[    5.094912] ThumbEE CPU extension supported.
[    5.099262] Registering SWP/SWPB emulation handler
[    5.104585] registered taskstats version 1
[    5.108779] zswap: loaded using pool lzo/zbud
[    5.113483] mmc1: host does not support reading read-only switch, assuming write-enable
[    5.114916] Btrfs loaded, crc32c=crc32c-generic
[    5.115901] Key type encrypted registered
[    5.125650] imx_thermal 2000000.aips-bus:tempmon: Extended Commercial CPU temperature grade - max:105C critical:100C passive:95C
[    5.126966] input: gpio-keys as /devices/soc0/gpio-keys/input/input0
[    5.149054] rtc-pcf8523 2-0068: hctosys: unable to read the hardware clock
[    5.154101] mmc1: new high speed SDHC card at address 0001
[    5.154653] mmcblk1: mmc1:0001 00000 29.2 GiB
[    5.165948] sr_init: No PMIC hook to init smartreflex
[    5.171235] sr_init: platform driver register failed for SR
[    5.171810]  mmcblk1: p1
[    5.196140] ALSA device list:
[    5.199133]   No soundcards found.
[    5.202743] Waiting for root device /dev/mmcblk0p1...
[   12.046104] random: fast init done
[  120.796131] random: crng init done


Please, advice what to try next!
Last edited by Oleg on Mon Feb 06, 2017 9:10 pm, edited 2 times in total.
Oleg
 
Posts: 22
Joined: Tue Jun 23, 2015 1:28 pm

Re: CuBox-i: no boot with kernel 4.9.6-1

Postby Oleg » Sat Jan 28, 2017 3:06 pm

Updated to 4.9.6-1, still no luck to boot:
Code: Select all
U-Boot SPL 2013.10-rc4 (Nov 05 2015 - 12:59:56)
Boot Device: SD1
spl: error reading image u-boot.img, err - -1
Load image from RAW...


U-Boot 2013.10-rc4 (Nov 05 2015 - 12:59:56)

CPU:   Freescale i.MX6Q rev1.5 at 792 MHz
Reset cause: POR
Board: MX6-CuBox-i
DRAM:  1 GiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0
mmc0 is current device
** File not found /boot.scr **
** File not found /uEnv.txt **
** File not found /zImage **
** File not found /uImage **
** File not found /boot/boot.scr **
211 bytes read in 53 ms (2.9 KiB/s)
Importing environment from mmc0 ...
5652208 bytes read in 340 ms (15.9 MiB/s)
Booting from mmc ...
** File not found /boot/initramfs-linux.img **
Loaded initramfs-linux.img
** File not found /boot/imx6q-cubox-i.dtb **
48226 bytes read in 2145 ms (21.5 KiB/s)
Loaded imx6q-cubox-i.dtb
Booting zImage
Kernel image @ 0x10800000 [ 0x000000 - 0x563ef0 ]
## Flattened Device Tree blob at 18000000
   Booting using the fdt blob at 0x18000000
   Using Device Tree in place at 18000000, end 1800ec61

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.6-1-ARCH (builduser@leming) (gcc version 6.3.1 20170109 (GCC) ) #1 SMP Thu Jan 26 20:34:49 MST 2017
[    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt:Machine model: SolidRun Cubox-i Dual/Quad
[    0.000000] cma: Reserved 48 MiB at 0x4d000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] percpu: Embedded 14 pages/cpu @ef6bc000 s26828 r8192 d22324 u57344
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260416
[    0.000000] Kernel command line: root=/dev/mmcblk0p1 rootwait rw console=tty1 console=ttymxc0,115200 consoleblank=0 video=mxcfb0:dev=hdmi,1280x720M@60,if=RGB24,bpp=16 dmfc=3 ahci_imx.hotplug=1 pci=nomsi loop.max_part=15
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 964368K/1048576K available (11264K kernel code, 946K rwdata, 4528K rodata, 1024K init, 840K bss, 35056K reserved, 49152K cma-reserved, 212992K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0c00000   (12256 kB)
[    0.000000]       .init : 0xc1100000 - 0xc1200000   (1024 kB)
[    0.000000]       .data : 0xc1200000 - 0xc12ec8a8   ( 947 kB)
[    0.000000]        .bss : 0xc12ee000 - 0xc13c01f8   ( 841 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]    Build-time adjustment of leaf fanout to 32.
[    0.000000]    RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] L2C-310 errata 752271 769419 enabled
[    0.000000] L2C-310 enabling early BRESP for Cortex-A9
[    0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[    0.000000] L2C-310 ID prefetch enabled, offset 16 lines
[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB
[    0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001
[    0.000000] Switching to timer-based delay loop, resolution 333ns
[    0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns
[    0.000026] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns
[    0.002196] Console: colour dummy device 80x30
[    0.002667] console [tty1] enabled
[    0.002713] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000)
[    0.002752] pid_max: default: 32768 minimum: 301
[    0.003021] Security Framework initialized
[    0.003228] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.003257] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.004013] CPU: Testing write buffer coherency: ok
[    0.004324] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.004396] Setting up static identity map for 0x10100000 - 0x10100098
[    0.008390] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.008483] Brought up 2 CPUs
[    0.008530] SMP: Total of 2 processors activated (12.00 BogoMIPS).
[    0.008551] CPU: All CPU(s) started in SVC mode.
[    0.009487] devtmpfs: initialized
[    0.020894] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.021269] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.023797] xor: measuring software checksum speed
[    0.119394]    arm4regs  :  1234.000 MB/sec
[    0.219395]    8regs     :   951.200 MB/sec
[    0.319393]    32regs    :  1028.000 MB/sec
[    0.419394]    neon      :   900.400 MB/sec
[    0.419416] xor: using function: arm4regs (1234.000 MB/sec)
[    0.419520] pinctrl core: initialized pinctrl subsystem
[    0.421096] NET: Registered protocol family 16
[    0.423651] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.459409] cpuidle: using governor menu
[    0.460361] CPU identified as i.MX6Q, silicon rev 1.5
[    0.479848] No ATAGs?
[    0.479884] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.479922] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.481593] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[    0.482750] Serial: AMBA PL011 UART driver
[    0.699568] raid6: int32x1  gen()   106 MB/s
[    0.869532] raid6: int32x1  xor()   146 MB/s
[    1.039576] raid6: int32x2  gen()   165 MB/s
[    1.209412] raid6: int32x2  xor()   167 MB/s
[    1.379714] raid6: int32x4  gen()   193 MB/s
[    1.549493] raid6: int32x4  xor()   165 MB/s
[    1.719514] raid6: int32x8  gen()   215 MB/s
[    1.889481] raid6: int32x8  xor()   153 MB/s
[    2.059470] raid6: neonx1   gen()   616 MB/s
[    2.229433] raid6: neonx1   xor()   454 MB/s
[    2.399482] raid6: neonx2   gen()   658 MB/s
[    2.569434] raid6: neonx2   xor()   579 MB/s
[    2.739412] raid6: neonx4   gen()   660 MB/s
[    2.909406] raid6: neonx4   xor()   524 MB/s
[    3.079445] raid6: neonx8   gen()   494 MB/s
[    3.249402] raid6: neonx8   xor()   446 MB/s
[    3.249429] raid6: using algorithm neonx4 gen() 660 MB/s
[    3.249448] raid6: .... xor() 524 MB/s, rmw enabled
[    3.249467] raid6: using intx1 recovery algorithm
[    3.263314] mxs-dma 110000.dma-apbh: initialized
[    3.269527] vgaarb: loaded
[    3.270288] SCSI subsystem initialized
[    3.270734] usbcore: registered new interface driver usbfs
[    3.270817] usbcore: registered new interface driver hub
[    3.270913] usbcore: registered new device driver usb
[    3.272099] i2c i2c-1: IMX I2C adapter registered
[    3.272138] i2c i2c-1: can't use DMA, using PIO instead.
[    3.272662] i2c i2c-2: IMX I2C adapter registered
[    3.272698] i2c i2c-2: can't use DMA, using PIO instead.
[    3.273601] media: Linux media interface: v0.10
[    3.273668] Linux video capture interface: v2.00
[    3.273752] pps_core: LinuxPPS API ver. 1 registered
[    3.273773] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    3.273818] PTP clock support registered
[    3.273862] EDAC MC: Ver: 3.0.0
[    3.274860] Advanced Linux Sound Architecture Driver Initialized.
[    3.275428] NetLabel: Initializing
[    3.275455] NetLabel:  domain hash size = 128
[    3.275473] NetLabel:  protocols = UNLABELED CIPSOv4
[    3.275542] NetLabel:  unlabeled traffic allowed by default
[    3.276071] clocksource: Switched to clocksource mxc_timer1
[    3.276265] VFS: Disk quotas dquot_6.6.0
[    3.276344] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    3.286867] NET: Registered protocol family 2
[    3.287504] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    3.287607] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    3.287744] TCP: Hash tables configured (established 8192 bind 8192)
[    3.287828] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    3.287883] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    3.288069] NET: Registered protocol family 1
[    3.288589] RPC: Registered named UNIX socket transport module.
[    3.288619] RPC: Registered udp transport module.
[    3.288638] RPC: Registered tcp transport module.
[    3.288657] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    3.289109] Unpacking initramfs...
[    3.289144] Initramfs unpacking failed: junk in compressed archive
[    3.293835] Freeing initrd memory: 5520K (c5100000 - c5664000)
[    3.294384] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[    3.296385] futex hash table entries: 512 (order: 3, 32768 bytes)
[    3.297282] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    3.303025] zbud: loaded
[    3.305587] NFS: Registering the id_resolver key type
[    3.305634] Key type id_resolver registered
[    3.305655] Key type id_legacy registered
[    3.305683] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    3.311550] Key type asymmetric registered
[    3.311630] bounce: pool size: 64 pages
[    3.311822] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    3.311969] io scheduler noop registered
[    3.311995] io scheduler deadline registered
[    3.312186] io scheduler cfq registered (default)
[    3.327530] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[    3.327583] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[    3.334897] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[    3.337662] Serial: AMBA driver
[    3.338431] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25, base_baud = 5000000) is a IMX
[    4.174403] console [ttymxc0] enabled
[    4.179015] 21f0000.serial: ttymxc3 at MMIO 0x21f0000 (irq = 66, base_baud = 5000000) is a IMX
[    4.188935] [drm] Initialized
[    4.199948] loop: module loaded
[    4.204868] Loading iSCSI transport class v2.0-870.
[    4.210195] iscsi: registered transport (tcp)
[    4.215523] ahci-imx 2200000.sata: fsl,transmit-level-mV value 1104, using 00000044
[    4.223252] ahci-imx 2200000.sata: fsl,transmit-boost-mdB value 0, using 00000000
[    4.230784] ahci-imx 2200000.sata: fsl,transmit-atten-16ths value 9, using 00002000
[    4.238486] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000
[    4.249019] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled
[    4.256031] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    4.264872] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
[    4.275220] scsi host0: ahci-imx
[    4.278821] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 69
[    4.290923] libphy: Fixed MDIO Bus: probed
[    4.296510] 2188000.ethernet supply phy not found, using dummy regulator
[    4.306805] pps pps0: new PPS source ptp0
[    4.315247] libphy: fec_enet_mii_bus: probed
[    4.320140] fec 2188000.ethernet eth0: registered PHC device 0
[    4.328935] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.335490] ehci-pci: EHCI PCI platform driver
[    4.340024] ehci-platform: EHCI generic platform driver
[    4.345511] ehci-mxc: Freescale On-Chip EHCI Host driver
[    4.350958] ehci-omap: OMAP-EHCI Host Controller driver
[    4.356377] ehci-orion: EHCI orion driver
[    4.360549] ehci-exynos: EHCI EXYNOS driver
[    4.364917] tegra-ehci: Tegra EHCI driver
[    4.369138] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.375356] ohci-pci: OHCI PCI platform driver
[    4.379884] ohci-platform: OHCI generic platform driver
[    4.385312] ohci-exynos: OHCI EXYNOS driver
[    4.389705] ohci-omap3: OHCI OMAP3 driver
[    4.394311] usbcore: registered new interface driver uas
[    4.399744] usbcore: registered new interface driver usb-storage
[    4.405806] usbcore: registered new interface driver ums-cypress
[    4.411892] usbcore: registered new interface driver ums_eneub6250
[    4.418157] usbcore: registered new interface driver ums-freecom
[    4.424215] usbcore: registered new interface driver ums-isd200
[    4.430237] usbcore: registered new interface driver ums-usbat
[    4.445746] ci_hdrc ci_hdrc.0: EHCI Host Controller
[    4.446992] ci_hdrc ci_hdrc.1: EHCI Host Controller
[    4.447028] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[    4.462678] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2
[    4.476103] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[    4.481699] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.488537] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.495790] usb usb1: Product: EHCI Host Controller
[    4.500702] usb usb1: Manufacturer: Linux 4.9.6-1-ARCH ehci_hcd
[    4.506119] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[    4.512059] usb usb1: SerialNumber: ci_hdrc.1
[    4.517083] hub 1-0:1.0: USB hub found
[    4.520902] hub 1-0:1.0: 1 port detected
[    4.525357] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    4.532220] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.539494] usb usb2: Product: EHCI Host Controller
[    4.544394] usb usb2: Manufacturer: Linux 4.9.6-1-ARCH ehci_hcd
[    4.550347] usb usb2: SerialNumber: ci_hdrc.0
[    4.554904] rtc-pcf8523 2-0068: rtc core: registered rtc-pcf8523 as rtc0
[    4.555398] hub 2-0:1.0: USB hub found
[    4.555432] hub 2-0:1.0: 1 port detected
[    4.570628] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
[    4.580097] i2c /dev entries driver
[    4.591769] sdhci: Secure Digital Host Controller Interface driver
[    4.597998] sdhci: Copyright(c) Pierre Ossman
[    4.603522] Synopsys Designware Multimedia Card Interface Driver
[    4.610415] VUB300 Driver rom wait states = 1C irqpoll timeout = 0400[    4.617035] usbcore: registered new interface driver vub300
[    4.620696] ata1: SATA link down (SStatus 0 SControl 300)
[    4.628316] usbcore: registered new interface driver ushc
[    4.634186] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.640776] sdhci-esdhc-imx 2190000.usdhc: allocated mmc-pwrseq
[    4.926107] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[    4.935823] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state, work on normal mode
[    4.945072] sdhci-esdhc-imx 2194000.usdhc: Got CD GPIO
[    5.026235] mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
[    5.035436] ledtrig-cpu: registered to indicate activity on CPUs
[    5.043848] hidraw: raw HID events driver (C) Jiri Kosina
[    5.056245] usbcore: registered new interface driver usbhid
[    5.061842] usbhid: USB HID core driver
[    5.065907] ashmem: initialized
[    5.074193] NET: Registered protocol family 10
[    5.079736] mip6: Mobile IPv6
[    5.082735] NET: Registered protocol family 17
[    5.087296] Key type dns_resolver registered
[    5.094545] ThumbEE CPU extension supported.
[    5.098885] Registering SWP/SWPB emulation handler
[    5.103445] mmc1: host does not support reading read-only switch, assuming write-enable
[    5.109344] mmc1: new high speed SDHC card at address 0001
[    5.109887] mmcblk1: mmc1:0001 00000 29.2 GiB
[    5.122298] registered taskstats version 1
[    5.122446]  mmcblk1: p1
[    5.129067] zswap: loaded using pool lzo/zbud
[    5.135111] Btrfs loaded, crc32c=crc32c-generic
[    5.140665] Key type encrypted registered
[    5.154549] imx_thermal 2000000.aips-bus:tempmon: Extended Commercial CPU temperature grade - max:105C critical:100C passive:95C
[    5.167393] input: gpio-keys as /devices/soc0/gpio-keys/input/input0
[    5.175259] rtc-pcf8523 2-0068: hctosys: unable to read the hardware clock
[    5.182181] sr_init: No PMIC hook to init smartreflex
[    5.187479] sr_init: platform driver register failed for SR
[    5.196139] ALSA device list:
[    5.199133]   No soundcards found.
[    5.202759] Waiting for root device /dev/mmcblk0p1...
[   11.116299] random: fast init done
[  120.796103] random: crng init done
Oleg
 
Posts: 22
Joined: Tue Jun 23, 2015 1:28 pm

Re: CuBox-i: no boot with kernel 4.9.6-1

Postby Oleg » Sat Feb 04, 2017 2:24 am

I had no luck with kernel 4.9.7-1 also.
Oleg
 
Posts: 22
Joined: Tue Jun 23, 2015 1:28 pm

CuBox-i: no boot with kernel 4.9.8-1

Postby Oleg » Mon Feb 06, 2017 9:10 pm

Even with 4.9.8-1 no luck.
Oleg
 
Posts: 22
Joined: Tue Jun 23, 2015 1:28 pm

Re: CuBox-i: no boot with kernel 4.9.8-1

Postby uxu » Sat Feb 11, 2017 12:08 pm

Hi,

as it is said, those who can read have a clear advantage:
[ 5.109344] mmc1: new high speed SDHC card at address 0001
[ 5.109887] mmcblk1: mmc1:0001 00000 29.2 GiB

The new kernel recognizes a new sdcard interface in front of the real one, and therefore you need to adjust your linux kernel parameters. Root is no more on /dev/mmcblk0p1 but on /dev/mmcblk1p1. I can say that say from own experience, that the new kernel works like a charm and this answer is my way of saying thanks to all the people who have worked hard to provide such good support for this piece of hardware.

Regards, Felix
uxu
 
Posts: 1
Joined: Sat Feb 11, 2017 11:55 am

Re: CuBox-i: no boot with kernel 4.9.8-1

Postby Oleg » Sat Feb 11, 2017 5:25 pm

Today I have installed kernel 4.9.9-1 and uboot-cubox-i 2017.01-1 and got both my cubes back to action! Thanks!
Oleg
 
Posts: 22
Joined: Tue Jun 23, 2015 1:28 pm

Re: CuBox-i: no boot with kernel 4.9.8-1

Postby msalerno » Wed Feb 15, 2017 11:39 pm

Which kernel package did you use? linux-armv7?
msalerno
 
Posts: 20
Joined: Wed Apr 16, 2014 11:13 pm

Re: CuBox-i: no boot with kernel 4.9.8-1

Postby Oleg » Fri Feb 17, 2017 3:30 am

I use linux-armv7 and linux-armv7-cubox.
Oleg
 
Posts: 22
Joined: Tue Jun 23, 2015 1:28 pm

Re: CuBox-i: no boot with kernel 4.9.8-1

Postby lynx » Mon Feb 27, 2017 9:36 pm

Today I have installed kernel 4.9.9-1 and uboot-cubox-i 2017.01-1 and got both my cubes back to action! Thanks!


Oleg, could you please describe what you have done?

I've got an issue with my Hummingboard (IMX6) and ArchLinux after the new release of "uboot-cubox-i 2017.01-1".
Even if wipe everything and install fresh ArchLinux as described here: https://archlinuxarm.org/platforms/armv ... le/cubox-i
I'm able to get into console, but the first run of "pacman -Syu" makes the device useless again :(

Simple steps on how to get from http://os.archlinuxarm.org/os/ArchLinux ... est.tar.gz to "kernel 4.9.9-1 and uboot-cubox-i 2017.01-1" would be a great help to me!

I'm also curious to know how to update to "kernel 4.9.9-1", since original "ArchLinuxARM-imx6-cubox-latest.tar.gz" comes with 3.14.x kernel. Are you simply follow this: http://forum.solid-run.com/viewtopic.php?f=10&t=1156 or there are any additional ArchLinux tricks?


Thank you in advance!
lynx
 
Posts: 4
Joined: Wed Sep 19, 2012 9:37 pm

Re: CuBox-i: no boot with kernel 4.9.8-1

Postby Oleg » Thu Mar 09, 2017 5:22 am

lynx, install first linux-armv7-cubox
Oleg
 
Posts: 22
Joined: Tue Jun 23, 2015 1:28 pm


Return to Freescale

Who is online

Users browsing this forum: No registered users and 1 guest