by ckhmer1 » Thu Jan 28, 2016 10:22 pm
Hi,
finally I've figure out to boot armlinuxarm on my iMX53 loco (QSB).
Several firmware files are missing.
Following the output from u-boot to login:
$this->bbcode_second_pass_code('', '
U-Boot 2016.01 (Jan 28 2016 - 23:16:26 +0100) Arch Linux ARM
CPU: Freescale i.MX53 rev2.1 at 800 MHz
Reset cause: POR
Board: MX53 LOCO
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
691 bytes read in 65 ms (9.8 KiB/s)
Running bootscript from mmc ...
## Executing script at 70800000
baudrate=115200
boot_fdt=try
bootargs=console=ttyGS0,115200 root=PARTUUID=e05cb4d1-01 rw rootwait video=mxcdi1fb:RGB24,VGA-SXGA vga di1_primy
bootcmd=mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimagi
bootdelay=1
bootpart=1
bootscript=echo Running bootscript from mmc ...; source ${scriptaddr}
console=ttymxc0,115200
devnum=0
devtype=mmc
ethact=FEC
ethaddr=00:04:9f:02:71:a3
ethprime=FEC0
fdt_addr=0x71000000
fdt_file=imx53-qsrb.dtb
fileaddr=70800000
filesize=2b3
hostname=imx53loco
image=/boot/zImage
ip_dyn=yes
loadaddr=0x72000000
loadbootscript=load mmc ${mmcdev}:${mmcpart} ${scriptaddr} ${script};
loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} /boot/dtbs/${fdt_file}
loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}
mmcargs=setenv bootargs console=ttymxc0,${baudrate} root=${mmcroot} video=mxcdi1fb:RGB24,VGA-SXGA vga di1_primay
mmcboot=echo Booting from mmc ...; run mmcargs; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if ru;
mmcdev=0
mmcpart=1
mmcroot=/dev/mmcblk0p1 rw rootwait
netargs=setenv bootargs console=ttymxc0,${baudrate} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcpy
netboot=echo Booting from net ...; run netargs; if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv ;
ramdisk_addr_r=0x73000000
script=/boot/boot.scr
scriptaddr=0x70800000
uuid=e05cb4d1-01
Environment size: 2015/8188 bytes
5198336 bytes read in 335 ms (14.8 MiB/s)
Booting from mmc ...
33793 bytes read in 917 ms (35.2 KiB/s)
Kernel image @ 0x72000000 [ 0x000000 - 0x4f5200 ]
## Flattened Device Tree blob at 71000000
Booting using the fdt blob at 0x71000000
Loading Device Tree to 8f54b000, end 8f556400 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.3.3-1-ARCH (builduser@leming) (gcc version 5.3.0 (GCC) ) #1 SMP Fri Dec 18 18:485
[ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Freescale i.MX53 Quick Start-R Board
[ 0.000000] cma: Reserved 24 MiB at 0xce800000
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] PERCPU: Embedded 13 pages/cpu @dffcd000 s24256 r8192 d20800 u53248
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260992
[ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p1 rw rootwait video=mxcdi1fb:RGB24y
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 995476K/1048576K available (10752K kernel code, 1236K rwdata, 4512K rodata, 1220K init, )
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0ef04c4 (15266 kB)
[ 0.000000] .init : 0xc0ef1000 - 0xc1022000 (1220 kB)
[ 0.000000] .data : 0xc1022000 - 0xc1157378 (1237 kB)
[ 0.000000] .bss : 0xc115a000 - 0xc1242500 ( 930 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] TrustZone Interrupt Controller (TZIC) initialized
[ 0.000000] CPU identified as i.MX53, silicon rev 2.1
[ 0.000000] Switching to timer-based delay loop, resolution 29ns
[ 0.000008] sched_clock: 32 bits at 33MHz, resolution 29ns, wraps every 64424507889ns
[ 0.000030] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 57337812242 ns
[ 0.002909] Console: colour dummy device 80x30
[ 0.002951] Calibrating delay loop (skipped), value calculated using timer frequency.. 66.66 BogoMIPS (lpj=1)
[ 0.002972] pid_max: default: 32768 minimum: 301
[ 0.003124] Security Framework initialized
[ 0.003326] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.003340] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.004317] Initializing cgroup subsys io
[ 0.004359] Initializing cgroup subsys memory
[ 0.004418] Initializing cgroup subsys devices
[ 0.004441] Initializing cgroup subsys freezer
[ 0.004461] Initializing cgroup subsys net_cls
[ 0.004477] Initializing cgroup subsys perf_event
[ 0.004494] Initializing cgroup subsys net_prio
[ 0.004513] Initializing cgroup subsys pids
[ 0.004594] CPU: Testing write buffer coherency: ok
[ 0.004644] ftrace: allocating 39258 entries in 116 pages
[ 0.093591] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.093728] Setting up static identity map for 0x70008280 - 0x70008318
[ 0.097605] Brought up 1 CPUs
[ 0.097629] SMP: Total of 1 processors activated (66.66 BogoMIPS).
[ 0.097639] CPU: All CPU(s) started in SVC mode.
[ 0.099726] devtmpfs: initialized
[ 0.115854] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 0.116916] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns
[ 0.119460] xor: measuring software checksum speed
[ 0.168592] arm4regs : 1219.200 MB/sec
[ 0.218692] 8regs : 903.200 MB/sec
[ 0.268791] 32regs : 1172.800 MB/sec
[ 0.318892] neon : 871.200 MB/sec
[ 0.318901] xor: using function: arm4regs (1219.200 MB/sec)
[ 0.319139] pinctrl core: initialized pinctrl subsystem
[ 0.321321] NET: Registered protocol family 16
[ 0.324149] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.326249] cpuidle: using governor ladder
[ 0.326273] cpuidle: using governor menu
[ 0.343115] No ATAGs?
[ 0.343147] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.345026] imx53-pinctrl 53fa8000.iomuxc: initialized IMX pinctrl driver
[ 0.346422] Serial: AMBA PL011 UART driver
[ 0.444704] raid6: int32x1 gen() 153 MB/s
[ 0.529982] raid6: int32x1 xor() 128 MB/s
[ 0.615396] raid6: int32x2 gen() 201 MB/s
[ 0.700344] raid6: int32x2 xor() 135 MB/s
[ 0.785553] raid6: int32x4 gen() 176 MB/s
[ 0.870869] raid6: int32x4 xor() 123 MB/s
[ 0.956263] raid6: int32x8 gen() 158 MB/s
[ 1.041433] raid6: int32x8 xor() 105 MB/s
[ 1.126412] raid6: neonx1 gen() 785 MB/s
[ 1.211644] raid6: neonx1 xor() 653 MB/s
[ 1.296865] raid6: neonx2 gen() 1184 MB/s
[ 1.382047] raid6: neonx2 xor() 908 MB/s
[ 1.467263] raid6: neonx4 gen() 766 MB/s
[ 1.552500] raid6: neonx4 xor() 640 MB/s
[ 1.637693] raid6: neonx8 gen() 436 MB/s
[ 1.722979] raid6: neonx8 xor() 226 MB/s
[ 1.722987] raid6: using algorithm neonx2 gen() 1184 MB/s
[ 1.722995] raid6: .... xor() 908 MB/s, rmw enabled
[ 1.723002] raid6: using intx1 recovery algorithm
[ 1.731819] vgaarb: loaded
[ 1.733213] SCSI subsystem initialized
[ 1.734004] usbcore: registered new interface driver usbfs
[ 1.734090] usbcore: registered new interface driver hub
[ 1.734222] usbcore: registered new device driver usb
[ 1.734440] 50000000.aips:usbphy@0 supply vcc not found, using dummy regulator
[ 1.734592] 50000000.aips:usbphy@1 supply vcc not found, using dummy regulator
[ 1.736550] i2c i2c-1: IMX I2C adapter registered
[ 1.736580] i2c i2c-1: can't use DMA
[ 1.738712] mc13xxx 0-0008: mc34708: rev 2.4, fin: 0, fab: 0
[ 1.746756] i2c i2c-0: IMX I2C adapter registered
[ 1.746784] i2c i2c-0: can't use DMA
[ 1.747773] media: Linux media interface: v0.10
[ 1.747862] Linux video capture interface: v2.00
[ 1.748000] pps_core: LinuxPPS API ver. 1 registered
[ 1.748008] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.748055] PTP clock support registered
[ 1.748218] EDAC MC: Ver: 3.0.0
[ 1.750201] Advanced Linux Sound Architecture Driver Initialized.
[ 1.751121] NetLabel: Initializing
[ 1.751134] NetLabel: domain hash size = 128
[ 1.751141] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.751204] NetLabel: unlabeled traffic allowed by default
[ 1.751710] clocksource: Switched to clocksource mxc_timer1
[ 1.868632] NET: Registered protocol family 2
[ 1.869573] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.869627] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.869691] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.869830] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 1.869854] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 1.870254] NET: Registered protocol family 1
[ 1.870802] RPC: Registered named UNIX socket transport module.
[ 1.870819] RPC: Registered udp transport module.
[ 1.870826] RPC: Registered tcp transport module.
[ 1.870833] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.872559] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available
[ 1.875097] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 1.885043] zbud: loaded
[ 1.885788] VFS: Disk quotas dquot_6.6.0
[ 1.886045] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.888774] NFS: Registering the id_resolver key type
[ 1.888862] Key type id_resolver registered
[ 1.888871] Key type id_legacy registered
[ 1.888902] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.898618] bounce: pool size: 64 pages
[ 1.898938] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.899242] io scheduler noop registered
[ 1.899264] io scheduler deadline registered
[ 1.899343] io scheduler cfq registered (default)
[ 1.910940] imx-sdma 63fb0000.sdma: no event needs to be remapped
[ 1.911164] imx-sdma 63fb0000.sdma: Direct firmware load for imx/sdma/sdma-imx53.bin failed with error -2
[ 1.911178] imx-sdma 63fb0000.sdma: Falling back to user helper
[ 1.915145] imx-sdma 63fb0000.sdma: initialized
[ 1.999484] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 2.002922] Serial: AMBA driver
[ 2.003827] 53fbc000.serial: ttymxc0 at MMIO 0x53fbc000 (irq = 47, base_baud = 4166666) is a IMX
[ 2.839650] console [ttymxc0] enabled
[ 2.845720] [drm] Initialized drm 1.1.0 20060810
[ 2.863508] loop: module loaded
[ 2.868902] Loading iSCSI transport class v2.0-870.
[ 2.874571] iscsi: registered transport (tcp)
[ 2.882228] ahci-imx 10000000.sata: SSS flag set, parallel bus scan disabled
[ 2.889381] ahci-imx 10000000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 2.898299] ahci-imx 10000000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc
[ 2.908594] scsi host0: ahci-imx
[ 2.912341] ata1: SATA max UDMA/133 mmio [mem 0x10000000-0x10000fff] port 0x100 irq 44
[ 2.925384] 63fec000.ethernet supply phy not found, using dummy regulator
[ 2.946316] libphy: fec_enet_mii_bus: probed
[ 2.955678] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.962469] ehci-pci: EHCI PCI platform driver
[ 2.967111] ehci-platform: EHCI generic platform driver
[ 2.972739] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 2.978251] ehci-omap: OMAP-EHCI Host Controller driver
[ 2.983691] ehci-orion: EHCI orion driver
[ 2.987909] ehci-exynos: EHCI EXYNOS driver
[ 2.992313] tegra-ehci: Tegra EHCI driver
[ 2.996505] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.002774] ohci-pci: OHCI PCI platform driver
[ 3.007355] ohci-platform: OHCI generic platform driver
[ 3.012828] ohci-exynos: OHCI EXYNOS driver
[ 3.017255] ohci-omap3: OHCI OMAP3 driver
[ 3.021509] usbcore: registered new interface driver uas
[ 3.026996] usbcore: registered new interface driver usb-storage
[ 3.033110] usbcore: registered new interface driver ums-cypress
[ 3.039220] usbcore: registered new interface driver ums_eneub6250
[ 3.045496] usbcore: registered new interface driver ums-freecom
[ 3.051732] usbcore: registered new interface driver ums-isd200
[ 3.057759] usbcore: registered new interface driver ums-usbat
[ 3.073929] ci_hdrc ci_hdrc.1: EHCI Host Controller
[ 3.079297] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
[ 3.091717] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
[ 3.097425] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.104266] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.111519] usb usb1: Product: EHCI Host Controller
[ 3.116427] usb usb1: Manufacturer: Linux 4.3.3-1-ARCH ehci_hcd
[ 3.122378] usb usb1: SerialNumber: ci_hdrc.1
[ 3.127705] hub 1-0:1.0: USB hub found
[ 3.131535] hub 1-0:1.0: 1 port detected
[ 3.141170] i2c /dev entries driver
[ 3.151957] coda 63ff4000.vpu: Direct firmware load for v4l-coda7541-imx53.bin failed with error -2
[ 3.161129] coda 63ff4000.vpu: Falling back to user helper
[ 3.171144] imx2-wdt 53f98000.wdog: timeout 60 sec (nowayout=1)
[ 3.179582] sdhci: Secure Digital Host Controller Interface driver
[ 3.185911] sdhci: Copyright(c) Pierre Ossman
[ 3.191512] Synopsys Designware Multimedia Card Interface Driver
[ 3.198595] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.204988] /soc/aips@50000000/spba@50000000/esdhc@50004000: voltage-ranges unspecified
[ 3.213337] sdhci-esdhc-imx 50004000.esdhc: No vmmc regulator found
[ 3.219681] sdhci-esdhc-imx 50004000.esdhc: No vqmmc regulator found
[ 3.251734] ata1: SATA link down (SStatus 0 SControl 300)
[ 3.257248] ahci-imx 10000000.sata: no device found, disabling link.
[ 3.263653] ahci-imx 10000000.sata: pass ahci_imx..hotplug=1 to enable hotplug
[ 3.270961] mmc0: SDHCI controller on 50004000.esdhc [50004000.esdhc] using ADMA
[ 3.280384] /soc/aips@50000000/spba@50000000/esdhc@50020000: voltage-ranges unspecified
[ 3.290584] sdhci-esdhc-imx 50020000.esdhc: Got CD GPIO
[ 3.295931] sdhci-esdhc-imx 50020000.esdhc: Got WP GPIO
[ 3.301411] sdhci-esdhc-imx 50020000.esdhc: No vmmc regulator found
[ 3.307770] sdhci-esdhc-imx 50020000.esdhc: No vqmmc regulator found
[ 3.340686] mmc0: host does not support reading read-only switch, assuming write-enable
[ 3.349066] mmc1: SDHCI controller on 50020000.esdhc [50020000.esdhc] using ADMA
[ 3.357754] mmc0: new high speed SD card at address a46f
[ 3.365046] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.372248] mmcblk0: mmc0:a46f SU01G 942 MiB
[ 3.380331] sahara: probe of 63ff8000.crypto failed with error -22
[ 3.386976] mmcblk0: p1
[ 3.393229] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.399563] usbcore: registered new interface driver usbhid
[ 3.405274] usbhid: USB HID core driver
[ 3.409641] ashmem: initialized
[ 3.419523] oprofile: using arm/armv7
[ 3.424758] NET: Registered protocol family 10
[ 3.431026] mip6: Mobile IPv6
[ 3.434167] NET: Registered protocol family 17
[ 3.438902] Key type dns_resolver registered
[ 3.445474] ThumbEE CPU extension supported.
[ 3.449888] Registering SWP/SWPB emulation handler
[ 3.455801] registered taskstats version 1
[ 3.460185] zswap: loaded using pool lzo/zbud
[ 3.468133] Btrfs loaded
[ 3.472600] Key type encrypted registered
[ 3.478967] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 3.486366] hctosys: unable to open rtc device (rtc0)
[ 3.491566] sr_init: No PMIC hook to init smartreflex
[ 3.496997] sr_init: platform driver register failed for SR
[ 3.502638] of_cfs_init
[ 3.505223] of_cfs_init: OK
[ 3.520909] Unable to find PPMU node
[ 3.524666] exynos5-bus-int: probe of exynos5-bus-int failed with error -2
[ 3.531987] ALSA device list:
[ 3.534962] No soundcards found.
[ 3.541887] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities
[ 3.551249] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities
[ 3.579602] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.587877] VFS: Mounted root (ext4 filesystem) on device 179:1.
[ 3.599087] devtmpfs: mounted
[ 3.603863] Freeing unused kernel memory: 1220K (c0ef1000 - c1022000)
[ 4.047656] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.066175] random: systemd urandom read with 30 bits of entropy available
[ 4.100919] systemd[1]: systemd 228 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYS)
[ 4.119888] systemd[1]: Detected architecture arm.
Welcome to Arch Linux ARM!
[ 4.148151] systemd[1]: Set hostname to <armory>.
[ 4.772283] systemd[1]: Listening on LVM2 metadata daemon socket.
[ OK ] Listening on LVM2 metadata daemon socket.
[ 4.817151] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ OK ] Set up automount Arbitrary Executab...ats File System Automount Point.
[ 4.842432] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ 4.867300] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 4.890099] systemd[1]: Created slice System Slice.
[ OK ] Created slice System Slice.
[ 4.908446] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 4.927257] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 4.942613] systemd[1]: Listening on Network Service Netlink Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ 4.963486] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 4.981979] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 4.996938] systemd[1]: Reached target Encrypted Volumes.
[ OK ] Reached target Encrypted Volumes.
[ 5.011937] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 5.027311] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 5.047166] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 5.076085] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 5.108631] systemd[1]: Mounting Debug File System...
Mounting Debug File System...
[ 5.149980] systemd[1]: Starting Create list of required static device nodes for the current kernel...
Starting Create list of required st... nodes for the current kernel...
[ 5.238564] systemd[1]: Starting Setup Virtual Console...
Starting Setup Virtual Console...
[ 5.257353] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 5.277108] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 5.302419] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ OK ] Listening on Device-mapper event daemon FIFOs.
[ 5.322372] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 5.689075] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 5.737327] systemd[1]: Mounting Temporary Directory...
Mounting Temporary Directory...
[ 5.762725] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ 5.797214] systemd[1]: Reached target Paths.
[ OK ] Reached target Paths.
[ 5.817188] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 5.857031] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 5.923456] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted POSIX Message Queue File System.
[ 5.947351] systemd[1]: Mounted Debug File System.
[ OK ] Mounted Debug File System.
[ 5.967335] systemd[1]: Mounted Temporary Directory.
[ OK ] Mounted Temporary Directory.
[ 5.982906] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ OK ] Started Load Kernel Modules.
[ OK ] Started Create list of required sta...ce nodes for the current kernel.
[ OK ] Started Setup Virtual Console.
[ OK ] Started Remount Root and Kernel File Systems.
Starting udev Coldplug all Devices...
Starting Load/Save Random Seed...
Starting Create Static Device Nodes in /dev...
Starting Apply Kernel Variables...
Mounting Configuration File System...
Starting Flush Journal to Persistent Storage...
[ OK ] Mounted Configuration File System.
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Create Static Device Nodes in /dev.
[ OK ] Started Apply Kernel Variables.
[ 6.734909] systemd-journald[125]: Received request to flush runtime journal from PID 1
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Reached target Local File Systems.
Starting udev Kernel Device Manager...
[ 7.138434] random: nonblocking pool is initialized
[ OK ] Started Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories...
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Network Time Synchronization.
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Time Synchronized.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily rotation of log files.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Started Daily man-db cache update.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting SSH Key Generation...
Starting Permit User Sessions...
[ OK ] Started Entropy Harvesting Daemon.
Starting Login Service...
[ OK ] Started D-Bus System Message Bus.
Starting Network Service...
[ OK ] Started Daily verification of password and group files.
[ OK ] Reached target Timers.
[ OK ] Started SSH Key Generation.
[ OK ] Started Permit User Sessions.
[ OK ] Started Network Service.
[ OK ] Started Login Service.
[ OK ] Reached target Network.
Starting Network Name Resolution...
[ OK ] Started Getty on tty1.
[ OK ] Started OpenSSH Daemon.
[ OK ] Started Network Name Resolution.
[ OK ] Found device /dev/ttymxc0.
[ OK ] Started Serial Getty on ttymxc0.
[ 11.911013] input: mma8450 as /devices/platform/soc/60000000.aips/63fc8000.i2c/i2c-0/0-001c/input/input1
[ 11.956976] sgtl5000 1-000a: sgtl5000 revision 0x11
[ 12.008727] mc13xxx-led: probe of mc34708-led failed with error -61
[ 12.131227] imx-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
[ 12.138083] imx-sgtl5000 sound: snd_soc_register_card failed (-517)
[ 12.355075] sgtl5000 1-000a: Using internal LDO instead of VDDD
[ 12.389767] imx-sgtl5000 sound: sgtl5000 <-> 50014000.ssi mapping ok
Arch Linux 4.3.3-1-ARCH (ttymxc0)
armory login: [ 61.906964] imx-sdma 63fb0000.sdma: external firmware not found, using ROM firmware
[ 63.186928] coda 63ff4000.vpu: firmware request failed
')
Last edited by
WarheadsSE on Fri Jan 29, 2016 5:07 pm, edited 1 time in total.
Reason: FTFY; Code Tags