Mirabox upgrade to 4.1.0-1 Kernel kills ethernet

This forum is for supported devices using an ARMv7 Marvell SoC.

Mirabox upgrade to 4.1.0-1 Kernel kills ethernet

Postby shazled » Sat Jun 27, 2015 9:48 am

Hello,
I upgraded to the 4.1.0-1 armv7 and armv7-mirabox as part of pacman -Syu.

The ethernet stopped working although the interfaces come up as normal and appear normal. I can see no errors in dmesg or journalctl.

However the ethernet worked again after downgrading to 4.0.5-2:
$this->bbcode_second_pass_code('', '
# cd /var/cache/pacman/pkg/
# pacman -U linux-armv7-4.0.5-2-armv7h.pkg.tar.xz linux-armv7-mirabox-4.0.5-2-armv7h.pkg.tar.xz
')

This is the boot of the broken ethernet (4.1.0-1):

$this->bbcode_second_pass_code('', '
U-Boot 2009.08 (Sep 16 2012 - 22:50:06)Marvell version: 1.1.2 NQ
U-Boot Addressing:
Code: 00600000:006AFFF0
BSS: 006F8E40
Stack: 0x5fff70
PageTable: 0x8e0000
Heap address: 0x900000:0xe00000
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200Mhz, L2 @ 600Mhz
DDR @ 600Mhz, TClock @ 200Mhz
DDR 16Bit Width, FastPath Memory Access
PEX 0: Detected No Link.
PEX 1: Root Complex Interface, Detected Link X1
DRAM: 1 GB
CS 0: base 0x00000000 size 512 MB
CS 1: base 0x20000000 size 512 MB
Addresses 14M - 0M are saved for the U-Boot usage.
NAND: 1024 MiB
Bad block table found at page 262016, version 0x01
Bad block table found at page 261888, version 0x01
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
phy16= 72
phy16= 72
MMC: MRVL_MMC: 0
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 3  2  1  0
(Re)start USB...
USB: Active port: invalid port number 2, switching to port 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 4 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
scanning bus for storage devices... Device NOT ready
Request Sense returned 02 3A 00
2 Storage Device(s) found
reading uImage

4973588 bytes read
## Booting kernel from Legacy Image at 06400000 ...
Image Name: linux-armv7-mirabox
Created: 2015-06-24 5:32:30 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4973524 Bytes = 4.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.1.0-1-ARCH (builduser@leming) (gcc version 5.1.0 (GCC) ) #1 SMP Tue Jun 23 23:24:14 MDT 2015
[ 0.000000] CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine model: Globalscale Mirabox
[ 0.000000] cma: Reserved 16 MiB at 0x3f000000
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] PERCPU: Embedded 13 pages/cpu @eeed8000 s21568 r8192 d23488 u53248
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260434
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sdb2 rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1004392K/1048576K available (10329K kernel code, 1170K rwdata, 4052K rodata, 1112K init, 908K bss, 27800K reserved, 16384K cma-reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0e13734 (14382 kB)
[ 0.000000] .init : 0xc0e14000 - 0xc0f2a000 (1112 kB)
[ 0.000000] .data : 0xc0f2a000 - 0xc104ea78 (1171 kB)
[ 0.000000] .bss : 0xc1051000 - 0xc11343dc ( 909 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] L2C: DT/platform modifies aux control register: 0x12086300 -> 0x1a086302
[ 0.000000] Aurora cache controller enabled, 4 ways, 256 kB
[ 0.000000] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302
[ 0.000013] sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 114840871909ns
[ 0.000033] clocksource armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 102208375848 ns
[ 0.000956] Console: colour dummy device 80x30
[ 0.000979] Calibrating delay loop... 1195.21 BogoMIPS (lpj=2988032)
[ 0.060103] pid_max: default: 32768 minimum: 301
[ 0.060202] Security Framework initialized
[ 0.060347] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.060358] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.060958] Initializing cgroup subsys blkio
[ 0.060974] Initializing cgroup subsys memory
[ 0.061005] Initializing cgroup subsys devices
[ 0.061018] Initializing cgroup subsys freezer
[ 0.061030] Initializing cgroup subsys net_cls
[ 0.061040] Initializing cgroup subsys perf_event
[ 0.061052] Initializing cgroup subsys net_prio
[ 0.061098] CPU: Testing write buffer coherency: ok
[ 0.061128] ftrace: allocating 37672 entries in 111 pages
[ 0.121129] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.121215] Setting up static identity map for 0x8280 - 0x8318
[ 0.121646] mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1
[ 0.121785] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.122828] Brought up 1 CPUs
[ 0.122841] SMP: Total of 1 processors activated (1195.21 BogoMIPS).
[ 0.122847] CPU: All CPU(s) started in SVC mode.
[ 0.123353] devtmpfs: initialized
[ 0.128068] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.128490] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302231375000 ns
[ 0.129942] xor: measuring software checksum speed
[ 0.175078] arm4regs : 1102.400 MB/sec
[ 0.225074] 8regs : 927.200 MB/sec
[ 0.275074] 32regs : 1082.400 MB/sec
[ 0.275082] xor: using function: arm4regs (1102.400 MB/sec)
[ 0.275235] pinctrl core: initialized pinctrl subsystem
[ 0.276217] NET: Registered protocol family 16
[ 0.277762] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.285659] No ATAGs?
[ 0.285677] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.286974] Serial: AMBA PL011 UART driver
[ 0.380507] raid6: int32x1 gen() 145 MB/s
[ 0.465158] raid6: int32x1 xor() 169 MB/s
[ 0.550087] raid6: int32x2 gen() 225 MB/s
[ 0.635255] raid6: int32x2 xor() 134 MB/s
[ 0.720213] raid6: int32x4 gen() 199 MB/s
[ 0.805199] raid6: int32x4 xor() 151 MB/s
[ 0.890098] raid6: int32x8 gen() 205 MB/s
[ 0.975118] raid6: int32x8 xor() 133 MB/s
[ 0.975126] raid6: using algorithm int32x2 gen() 225 MB/s
[ 0.975131] raid6: .... xor() 134 MB/s, rmw enabled
[ 0.975137] raid6: using intx1 recovery algorithm
[ 0.979152] vgaarb: loaded
[ 0.980027] SCSI subsystem initialized
[ 0.980580] usbcore: registered new interface driver usbfs
[ 0.980640] usbcore: registered new interface driver hub
[ 0.980720] usbcore: registered new device driver usb
[ 0.981773] media: Linux media interface: v0.10
[ 0.981829] Linux video capture interface: v2.00
[ 0.981918] pps_core: LinuxPPS API ver. 1 registered
[ 0.981924] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.981950] PTP clock support registered
[ 0.982027] EDAC MC: Ver: 3.0.0
[ 0.983087] Advanced Linux Sound Architecture Driver Initialized.
[ 0.983688] NetLabel: Initializing
[ 0.983697] NetLabel: domain hash size = 128
[ 0.983702] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.983756] NetLabel: unlabeled traffic allowed by default
[ 0.984021] Switched to clocksource armada_370_xp_clocksource
[ 1.053427] NET: Registered protocol family 2
[ 1.054273] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 1.054332] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.054409] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.054480] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.054504] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.054673] NET: Registered protocol family 1
[ 1.054994] RPC: Registered named UNIX socket transport module.
[ 1.055005] RPC: Registered udp transport module.
[ 1.055010] RPC: Registered tcp transport module.
[ 1.055016] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.055688] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
[ 1.057416] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 1.064556] zpool: loaded
[ 1.064573] zbud: loaded
[ 1.065063] VFS: Disk quotas dquot_6.6.0
[ 1.065231] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.066735] NFS: Registering the id_resolver key type
[ 1.066781] Key type id_resolver registered
[ 1.066787] Key type id_legacy registered
[ 1.066810] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.067814] aufs 4.x-rcN-20150622
[ 1.070041] bounce: pool size: 64 pages
[ 1.070235] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.070415] io scheduler noop registered
[ 1.070430] io scheduler deadline registered
[ 1.070588] io scheduler cfq registered (default)
[ 1.073335] armada-370-pinctrl d0018000.pin-ctrl: registered pinctrl driver
[ 1.075302] irq: Cannot allocate irq_descs @ IRQ41, assuming pre-allocated
[ 1.075674] irq: Cannot allocate irq_descs @ IRQ73, assuming pre-allocated
[ 1.075905] irq: Cannot allocate irq_descs @ IRQ105, assuming pre-allocated
[ 1.076840] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[ 1.076857] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 1.076867] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 1.076878] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.076942] pci 0000:00:01.0: IOMMU is currently not supported for PCI
[ 1.077167] pci 0000:00:02.0: IOMMU is currently not supported for PCI
[ 1.077361] PCI: bus0: Fast back to back transfers disabled
[ 1.077372] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.077385] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.077516] PCI: bus1: Fast back to back transfers enabled
[ 1.077787] pci 0000:02:00.0: IOMMU is currently not supported for PCI
[ 1.078092] PCI: bus2: Fast back to back transfers disabled
[ 1.078188] pci 0000:00:02.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff]
[ 1.078200] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 1.078220] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8000000-0xf800ffff 64bit]
[ 1.078243] pci 0000:02:00.0: BAR 2: assigned [mem 0xf8010000-0xf8010fff 64bit]
[ 1.078264] pci 0000:02:00.0: BAR 4: assigned [mem 0xf8011000-0xf8011fff 64bit]
[ 1.078283] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 1.078294] pci 0000:00:02.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 1.078421] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 1.080039] mv_xor d0060800.xor: Marvell shared XOR driver
[ 1.104132] mv_xor d0060800.xor: Marvell XOR: ( xor cpy )
[ 1.129105] mv_xor d0060800.xor: Marvell XOR: ( xor cpy )
[ 1.129249] mv_xor d0060900.xor: Marvell shared XOR driver
[ 1.154105] mv_xor d0060900.xor: Marvell XOR: ( xor cpy )
[ 1.179106] mv_xor d0060900.xor: Marvell XOR: ( xor cpy )
[ 1.236115] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 1.238470] console [ttyS0] disabled
[ 1.258621] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 20, base_baud = 12500000) is a 16550A
[ 2.177515] console [ttyS0] enabled
[ 2.181438] Serial: AMBA driver
[ 2.185727] [drm] Initialized drm 1.1.0 20060810
[ 2.196071] loop: module loaded
[ 2.200270] Loading iSCSI transport class v2.0-870.
[ 2.205619] iscsi: registered transport (tcp)
[ 2.211750] pxa3xx-nand d00d0000.nand: This platform can't do DMA on this device
[ 2.219720] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x38
[ 2.226131] nand: Micron MT29F8G08ABABAWP
[ 2.230175] nand: 1024 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224
[ 2.237972] pxa3xx-nand d00d0000.nand: ECC strength 16, ECC step size 2048
[ 2.245471] Bad block table found at page 262016, version 0x01
[ 2.252118] Bad block table found at page 261888, version 0x01
[ 2.258493] 3 ofpart partitions found on MTD device pxa3xx_nand-0
[ 2.264637] Creating 3 MTD partitions on "pxa3xx_nand-0":
[ 2.270079] 0x000000000000-0x000000400000 : "U-Boot"
[ 2.276039] 0x000000400000-0x000000800000 : "Linux"
[ 2.281826] 0x000000800000-0x000040000000 : "Filesystem"
[ 2.290306] libphy: orion_mdio_bus: probed
[ 2.297331] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 2.302857] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1
[ 2.311113] xhci_hcd 0000:02:00.0: hcc params 0x200073a9 hci version 0x100 quirks 0x00000010
[ 2.320031] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.326891] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.334165] usb usb1: Product: xHCI Host Controller
[ 2.339081] usb usb1: Manufacturer: Linux 4.1.0-1-ARCH xhci-hcd
[ 2.345041] usb usb1: SerialNumber: 0000:02:00.0
[ 2.350313] hub 1-0:1.0: USB hub found
[ 2.354187] hub 1-0:1.0: 2 ports detected
[ 2.358686] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 2.364204] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[ 2.371868] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.378712] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.385983] usb usb2: Product: xHCI Host Controller
[ 2.390897] usb usb2: Manufacturer: Linux 4.1.0-1-ARCH xhci-hcd
[ 2.396856] usb usb2: SerialNumber: 0000:02:00.0
[ 2.402048] hub 2-0:1.0: USB hub found
[ 2.405901] hub 2-0:1.0: 2 ports detected
[ 2.410728] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.417358] ehci-pci: EHCI PCI platform driver
[ 2.421905] ehci-platform: EHCI generic platform driver
[ 2.427309] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 2.432732] ehci-omap: OMAP-EHCI Host Controller driver
[ 2.438088] ehci-orion: EHCI orion driver
[ 2.442289] orion-ehci d0050000.usb: EHCI Host Controller
[ 2.447956] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 3
[ 2.455944] orion-ehci d0050000.usb: irq 26, io mem 0xd0050000
[ 2.469041] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00
[ 2.475190] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.482037] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.489308] usb usb3: Product: EHCI Host Controller
[ 2.494222] usb usb3: Manufacturer: Linux 4.1.0-1-ARCH ehci_hcd
[ 2.500180] usb usb3: SerialNumber: d0050000.usb
[ 2.505403] hub 3-0:1.0: USB hub found
[ 2.509443] hub 3-0:1.0: 1 port detected
[ 2.513833] orion-ehci d0051000.usb: EHCI Host Controller
[ 2.519535] orion-ehci d0051000.usb: new USB bus registered, assigned bus number 4
[ 2.527364] orion-ehci d0051000.usb: irq 27, io mem 0xd0051000
[ 2.539038] orion-ehci d0051000.usb: USB 2.0 started, EHCI 1.00
[ 2.545202] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.552047] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.559318] usb usb4: Product: EHCI Host Controller
[ 2.564232] usb usb4: Manufacturer: Linux 4.1.0-1-ARCH ehci_hcd
[ 2.570190] usb usb4: SerialNumber: d0051000.usb
[ 2.575420] hub 4-0:1.0: USB hub found
[ 2.579280] hub 4-0:1.0: 1 port detected
[ 2.583662] ehci-exynos: EHCI EXYNOS driver
[ 2.588075] tegra-ehci: Tegra EHCI driver
[ 2.592267] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.598519] ohci-pci: OHCI PCI platform driver
[ 2.603072] ohci-platform: OHCI generic platform driver
[ 2.608455] ohci-exynos: OHCI EXYNOS driver
[ 2.612893] ohci-omap3: OHCI OMAP3 driver
[ 2.617111] usbcore: registered new interface driver uas
[ 2.622635] usbcore: registered new interface driver usb-storage
[ 2.628738] usbcore: registered new interface driver ums-cypress
[ 2.634837] usbcore: registered new interface driver ums_eneub6250
[ 2.641117] usbcore: registered new interface driver ums-freecom
[ 2.647217] usbcore: registered new interface driver ums-isd200
[ 2.653232] usbcore: registered new interface driver ums-usbat
[ 2.662020] rtc-mv d0010300.rtc: rtc core: registered d0010300.rtc as rtc0
[ 2.670136] i2c /dev entries driver
[ 2.674714] pca953x 0-0025: failed reading register
[ 2.693661] orion_wdt: Initial timeout 229 sec, nowayout
[ 2.700212] sdhci: Secure Digital Host Controller Interface driver
[ 2.706447] sdhci: Copyright(c) Pierre Ossman
[ 2.739133] Synopsys Designware Multimedia Card Interface Driver
[ 2.748872] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.755171] armada-370-pinctrl d0018000.pin-ctrl: unsupported function gpo on pin mpp63
[ 2.763271] pinctrl core: failed to register map default (0): invalid type given
[ 2.771479] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.778372] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.785479] usbcore: registered new interface driver usbhid
[ 2.791115] usbhid: USB HID core driver
[ 2.795226] ashmem: initialized
[ 2.801452] oprofile: using arm/armv7-ca9
[ 2.806433] NET: Registered protocol family 10
[ 2.811918] mip6: Mobile IPv6
[ 2.815006] NET: Registered protocol family 17
[ 2.819682] Key type dns_resolver registered
[ 2.825275] usb 3-1: new high-speed USB device number 2 using orion-ehci
[ 2.834087] ThumbEE CPU extension supported.
[ 2.838460] Registering SWP/SWPB emulation handler
[ 2.844300] registered taskstats version 1
[ 2.852032] Btrfs loaded
[ 2.856177] Key type encrypted registered
[ 2.861356] rtc-mv d0010300.rtc: setting system clock to 2015-06-27 09:31:08 UTC (1435397468)
[ 2.870045] sr_init: No PMIC hook to init smartreflex
[ 2.875375] sr_init: platform driver register failed for SR
[ 2.881038] of_cfs_init
[ 2.883572] of_cfs_init: OK
[ 2.889120] Unable to find PPMU node
[ 2.895207] usb 4-1: new high-speed USB device number 2 using orion-ehci
[ 2.902010] exynos5-bus-int: probe of exynos5-bus-int failed with error -2
[ 2.909139] ALSA device list:
[ 2.912165] No soundcards found.
[ 2.916170] Waiting for root device /dev/sdb2...
[ 2.974788] usb 3-1: New USB device found, idVendor=1a40, idProduct=0101
[ 2.981553] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.988739] usb 3-1: Product: USB 2.0 Hub
[ 2.993461] hub 3-1:1.0: USB hub found
[ 2.997412] hub 3-1:1.0: 4 ports detected
[ 3.044962] usb 4-1: New USB device found, idVendor=1286, idProduct=2042
[ 3.051727] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.058922] usb 4-1: Product: Bluetooth and Wireless LAN Composite Device
[ 3.065762] usb 4-1: Manufacturer: Marvell
[ 3.069894] usb 4-1: SerialNumber: 00117F67F607
[ 3.269279] usb 3-1.1: new high-speed USB device number 3 using orion-ehci
[ 3.383146] usb 3-1.1: New USB device found, idVendor=05e3, idProduct=0723
[ 3.390082] usb 3-1.1: New USB device strings: Mfr=3, Product=4, SerialNumber=0
[ 3.397453] usb 3-1.1: Product: USB Storage
[ 3.401671] usb 3-1.1: Manufacturer: Generic
[ 3.407200] usb-storage 3-1.1:1.0: USB Mass Storage device detected
[ 3.413847] usb-storage 3-1.1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[ 3.421006] scsi host0: usb-storage 3-1.1:1.0
[ 3.509271] usb 3-1.2: new high-speed USB device number 4 using orion-ehci
[ 3.623138] usb 3-1.2: New USB device found, idVendor=05e3, idProduct=0723
[ 3.630075] usb 3-1.2: New USB device strings: Mfr=3, Product=4, SerialNumber=0
[ 3.637447] usb 3-1.2: Product: USB Storage
[ 3.641665] usb 3-1.2: Manufacturer: Generic
[ 3.647192] usb-storage 3-1.2:1.0: USB Mass Storage device detected
[ 3.653754] usb-storage 3-1.2:1.0: Quirks match for vid 05e3 pid 0723: 8000
[ 3.660892] scsi host1: usb-storage 3-1.2:1.0
[ 4.425726] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 9451 PQ: 0 ANSI: 0
[ 4.434890] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.443049] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 4.665695] scsi 1:0:0:0: Direct-Access Generic STORAGE DEVICE 9451 PQ: 0 ANSI: 0
[ 4.674731] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 4.887136] sd 1:0:0:0: [sdb] 15628288 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 4.895876] sd 1:0:0:0: [sdb] Write Protect is off
[ 4.901876] sd 1:0:0:0: [sdb] No Caching mode page found
[ 4.907247] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 4.919810] sdb: sdb1 sdb2
[ 4.926503] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 4.933793] EXT4-fs (sdb2): couldn't mount as ext3 due to feature incompatibilities
[ 4.943034] EXT4-fs (sdb2): couldn't mount as ext2 due to feature incompatibilities
[ 4.970954] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.978731] VFS: Mounted root (ext4 filesystem) on device 8:18.
[ 4.989284] devtmpfs: mounted
[ 4.993469] Freeing unused kernel memory: 1112K (c0e14000 - c0f2a000)
[ 5.484799] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.490254] systemd[1]: Inserted module 'ip_tables'
[ 5.510507] random: systemd urandom read with 40 bits of entropy available
[ 5.526786] systemd[1]: systemd 221 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD +IDN)
[ 5.545493] systemd[1]: Detected architecture arm.

Welcome to Arch Linux ARM!

[ 5.575804] systemd[1]: Set hostname to <dog>.
[ 6.481242] systemd[1]: display-manager.service: Cannot add dependency job, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ OK ] Reached target Remote File Systems.
[ 6.514230] systemd[1]: Reached target Remote File Systems.
[ 6.520045] systemd[1]: Starting Remote File Systems.
[ 6.525514] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 6.533312] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 6.541421] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 6.549554] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ OK ] Reached target Swap.
[ 6.569169] systemd[1]: Reached target Swap.
[ 6.573564] systemd[1]: Starting Swap.
[ OK ] Reached target Paths.
[ 6.589152] systemd[1]: Reached target Paths.
[ 6.593631] systemd[1]: Starting Paths.
[ OK ] Set up automount Arbitrary Executab...ats File System Automount Point.
[ 6.614177] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 6.623814] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ OK ] Reached target Encrypted Volumes.
[ 6.644157] systemd[1]: Reached target Encrypted Volumes.
[ 6.649755] systemd[1]: Starting Encrypted Volumes.
[ OK ] Created slice Root Slice.
[ 6.669183] systemd[1]: Created slice Root Slice.
[ 6.674110] systemd[1]: Starting Root Slice.
[ OK ] Listening on Device-mapper event daemon FIFOs.
[ 6.694168] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 6.700901] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ OK ] Created slice System Slice.
[ 6.719183] systemd[1]: Created slice System Slice.
[ 6.724315] systemd[1]: Starting System Slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 6.744185] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 6.750659] systemd[1]: Starting system-serial\x2dgetty.slice.
[ OK ] Created slice system-netctl.slice.
[ 6.769181] systemd[1]: Created slice system-netctl.slice.
[ 6.774874] systemd[1]: Starting system-netctl.slice.
[ OK ] Created slice system-getty.slice.
[ 6.794182] systemd[1]: Created slice system-getty.slice.
[ 6.799788] systemd[1]: Starting system-getty.slice.
[ OK ] Listening on Journal Socket.
[ 6.814182] systemd[1]: Listening on Journal Socket.
[ 6.819403] systemd[1]: Starting Journal Socket.
[ 6.828869] systemd[1]: Mounting Temporary Directory...
Mounting Temporary Directory...
[ 6.852457] systemd[1]: Starting Setup Virtual Console...
Starting Setup Virtual Console...
[ 6.872449] systemd[1]: Mounting Debug File System...
Mounting Debug File System...
[ 6.902562] systemd[1]: Starting Create list of required static device nodes for the current kernel...
Starting Create list of required st... nodes for the current kernel...
[ 6.939999] systemd[1]: Mounted Huge Pages File System.
[ 6.961982] systemd[1]: Started Load Kernel Modules.
[ 6.972161] systemd[1]: Mounting Configuration File System...
Mounting Configuration File System...
[ 6.999429] systemd[1]: Mounted FUSE Control File System.
[ 7.015523] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 7.045586] systemd[1]: Started Set Up Additional Binary Formats.
[ OK ] Listening on LVM2 metadata daemon socket.
[ 7.064271] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 7.071203] systemd[1]: Starting LVM2 metadata daemon socket.
[ 7.095578] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on udev Kernel Socket.
[ 7.114194] systemd[1]: Listening on udev Kernel Socket.
[ 7.119724] systemd[1]: Starting udev Kernel Socket.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 7.139178] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 7.146347] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on Journal Socket (/dev/log).
[ 7.164173] systemd[1]: Listening on Journal Socket (/dev/log).
[ 7.170302] systemd[1]: Starting Journal Socket (/dev/log).
[ 7.179481] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ OK ] Listening on udev Control Socket.
[ 7.214253] systemd[1]: Listening on udev Control Socket.
[ 7.220408] systemd[1]: Starting udev Control Socket.
[ OK ] Created slice User and Session Slice.
[ 7.239404] systemd[1]: Created slice User and Session Slice.
[ 7.245469] systemd[1]: Starting User and Session Slice.
[ OK ] Reached target Slices.
[ 7.264234] systemd[1]: Reached target Slices.
[ 7.271956] systemd[1]: Starting Slices.
[ 7.280174] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 7.308225] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ OK ] Mounted Configuration File System.
[ 7.355401] systemd[1]: Mounted Configuration File System.
[ OK ] Mounted POSIX Message Queue File System.
[ 7.384285] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted Debug File System.
[ 7.404206] systemd[1]: Mounted Debug File System.
[ OK ] Mounted Temporary Directory.
[ 7.419179] systemd[1]: Mounted Temporary Directory.
[ OK ] Started Setup Virtual Console.
[ 7.439324] systemd[1]: Started Setup Virtual Console.
[ OK ] Started Create list of required sta...ce nodes for the current kernel.
[ 7.464205] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ OK ] Started Apply Kernel Variables.
[ 7.489313] systemd[1]: Started Apply Kernel Variables.
[ OK ] Started Remount Root and Kernel File Systems.
[ 7.509311] systemd[1]: Started Remount Root and Kernel File Systems.
[ 7.954473] systemd[1]: Started Rebuild Hardware Database.
[ 7.965082] systemd[1]: Starting udev Coldplug all Devices...
Starting udev Coldplug all Devices...
[ 7.989432] systemd[1]: Started Rebuild Dynamic Linker Cache.
[ 8.001802] systemd[1]: Starting Load/Save Random Seed...
Starting Load/Save Random Seed...
[ 8.024448] systemd[1]: Started First Boot Wizard.
[ 8.030556] systemd[1]: Started Create System Users.
[ 8.041497] systemd[1]: Starting Create Static Device Nodes in /dev...
Starting Create Static Device Nodes in /dev...
[ OK ] Started Load/Save Random Seed.
[ 8.169282] systemd[1]: Started Load/Save Random Seed.
[ 8.174807] random: nonblocking pool is initialized
[ OK ] Started Create Static Device Nodes in /dev.
[ 8.279264] systemd[1]: Started Create Static Device Nodes in /dev.
[ 8.420032] systemd[1]: Starting udev Kernel Device Manager...
Starting udev Kernel Device Manager...
[ OK ] Reached target Local File Systems (Pre).
[ 8.464261] systemd[1]: Reached target Local File Systems (Pre).
[ 8.479273] systemd[1]: Starting Local File Systems (Pre).
[ 8.488913] systemd[1]: Mounted Virtual Machine and Container Storage.
[ OK ] Started udev Kernel Device Manager.
[ 8.614315] systemd[1]: Started udev Kernel Device Manager.
[ OK ] Started Journal Service.
[ 8.969283] systemd[1]: Started Journal Service.
Starting Flush Journal to Persistent Storage...
[ 9.119673] systemd-journald[110]: Received request to flush runtime journal from PID 1
[ OK ] Started udev Coldplug all Devices.
[ OK ] Found device /dev/ttyS0.
[ 12.493429] mvneta d0070000.ethernet eth0: Using random mac address fe:e2:ba:6a:30:14
[ 12.554867] mvneta d0074000.ethernet eth1: Using random mac address 32:1f:a0:a2:2e:bc
[ 12.966853] Bluetooth: Core ver 2.20
[ 12.994210] NET: Registered protocol family 31
[ 12.998687] Bluetooth: HCI device and connection manager initialized
[ 13.013867] cfg80211: Calling CRDA to update world regulatory domain
[ 13.050676] Bluetooth: HCI socket layer initialized
[ 13.077632] Bluetooth: L2CAP socket layer initialized
[ 13.106953] Bluetooth: SCO socket layer initialized
[ 13.369520] mwifiex: rx work enabled, cpus 1
[ 13.404533] usbcore: registered new interface driver mwifiex_usb
[ 13.514131] usbcore: registered new interface driver btusb
[ 13.533484] usb 4-1: WLAN FW is active
[ 13.655005] ieee80211 phy0: ignoring F/W country code US
[ 13.681212] usb 4-1: driver_version = mwifiex 1.0 (14.68.22.p16)
[ OK ] Found device /sys/subsystem/net/devices/eth0.
[ OK ] Found device /sys/subsystem/net/devices/eth1.
[ OK ] Created slice system-systemd\x2drfkill.slice.
Starting Load/Save RF Kill Switch Status of rfkill1...
Starting Load/Save RF Kill Switch Status of rfkill0...
[ OK ] Reached target Bluetooth.
[ OK ] Started Load/Save RF Kill Switch Status of rfkill1.
[ OK ] Started Load/Save RF Kill Switch Status of rfkill0.
[ 15.707280] cfg80211: World regulatory domain updated:
[ 15.712543] cfg80211: DFS Master region: unset
[ 15.716954] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 15.726773] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.734874] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.742953] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.751020] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 15.760564] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 15.770103] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 15.778246] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 15.786303] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ OK ] Found device STORAGE_DEVICE 1.
Mounting /boot...
[ 16.212173] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 16.223971] cfg80211: Calling CRDA for country: DE
[ OK ] Mounted /boot.
[ 16.293588] cfg80211: Regulatory domain changed to country: DE
[ 16.299539] cfg80211: DFS Master region: ETSI
[ 16.303830] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 16.313678] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.321740] cfg80211: (5150000 KHz - 5250000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 16.331299] cfg80211: (5250000 KHz - 5350000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 16.340874] cfg80211: (5470000 KHz - 5725000 KHz @ 160000 KHz), (N/A, 2698 mBm), (0 s)
[ 16.349027] cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ OK ] Reached target Local File Systems.
[ OK ] Started Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories...
[ OK ] Started Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
Starting Network Time Synchronization...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Time Synchronized.
[ OK ] Reached target System Initialization.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Packet Filtering Framework...
Starting Permit User Sessions...
Starting Connection to home hub...
[ OK ] Started D-Bus System Message Bus.
[ 17.819308] nf_conntrack version 0.5.0 (15967 buckets, 63868 max)
Starting D-Bus System Message Bus...
[ INFO ] Network Service is not active.
[ 17.959924] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[DEPEND] Dependency failed for Wait for Network to be Configured.
Starting Protected home network...
[ OK ] Started Entropy Harvesting Daemon.
Starting Entropy Harvesting Daemon...
Starting Login Service...
[ OK ] Started Permit User Sessions.
[ 18.299947] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ OK ] Started Login Service.
[ OK ] Started Serial Getty on ttyS0.
Starting Serial Getty on ttyS0...
[ OK ] Started Getty on tty1.
Starting Getty on tty1...
[ OK ] Reached target Login Prompts.
[ OK ] Started Packet Filtering Framework.
[ 22.954492] mvneta d0070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 22.962445] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

Arch Linux 4.1.0-1-ARCH (ttyS0)
Last login: Sat Jun 27 11:28:28 on ttyS0
[root@dog ~]# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 532
link/ether fe:e2:ba:6a:30:14 brd ff:ff:ff:ff:ff:ff
inet 192.168.2.4/26 brd 192.168.2.63 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::fce2:baff:fe6a:3014/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default qlen 532
link/ether 32:1f:a0:a2:2e:bc brd ff:ff:ff:ff:ff:ff
4: mlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:11:7f:67:f6:07 brd ff:ff:ff:ff:ff:ff
[root@dog ~]# ping 192.168.2.1
PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.

--- 192.168.2.1 ping statistics ---
4 packets transmitted, 0 received, 100% packet loss, time 3006ms

')
shazled
 
Posts: 7
Joined: Tue Oct 07, 2014 9:39 pm

Re: Mirabox upgrade to 4.1.0-1 Kernel kills ethernet

Postby shazled » Sat Jun 27, 2015 9:49 am

This is the boot of the working ethernet:
$this->bbcode_second_pass_code('', '
U-Boot 2009.08 (Sep 16 2012 - 22:50:06)Marvell version: 1.1.2 NQ
U-Boot Addressing:
Code: 00600000:006AFFF0
BSS: 006F8E40
Stack: 0x5fff70
PageTable: 0x8e0000
Heap address: 0x900000:0xe00000
Board: DB-88F6710-BP
SoC: MV6710 A1
CPU: Marvell PJ4B v7 UP (Rev 1) LE
CPU @ 1200Mhz, L2 @ 600Mhz
DDR @ 600Mhz, TClock @ 200Mhz
DDR 16Bit Width, FastPath Memory Access
PEX 0: Detected No Link.
PEX 1: Root Complex Interface, Detected Link X1
DRAM: 1 GB
CS 0: base 0x00000000 size 512 MB
CS 1: base 0x20000000 size 512 MB
Addresses 14M - 0M are saved for the U-Boot usage.
NAND: 1024 MiB
Bad block table found at page 262016, version 0x01
Bad block table found at page 261888, version 0x01
FPU not initialized
USB 0: Host Mode
USB 1: Host Mode
Modules/Interfaces Detected:
RGMII0 Phy
RGMII1 Phy
PEX0 (Lane 0)
PEX1 (Lane 1)
phy16= 72
phy16= 72
MMC: MRVL_MMC: 0
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 3  2  1  0
(Re)start USB...
USB: Active port: invalid port number 2, switching to port 0
Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 4 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
scanning bus for storage devices... Device NOT ready
Request Sense returned 02 3A 00
2 Storage Device(s) found
reading uImage

4876409 bytes read
## Booting kernel from Legacy Image at 06400000 ...
Image Name: linux-armv7-mirabox
Created: 2015-06-13 2:11:40 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4876345 Bytes = 4.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.0.5-2-ARCH (builduser@leming) (gcc version 4.9.2 20150304 (prerelease) (GCC) ) #1 SMP Fri Jun 12 20:03:44 MDT 2015
[ 0.000000] CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine model: Globalscale Mirabox
[ 0.000000] cma: Reserved 16 MiB at 0x3f000000
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] PERCPU: Embedded 12 pages/cpu @eeedd000 s17024 r8192 d23936 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260434
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sdb2 rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1004896K/1048576K available (10079K kernel code, 957K rwdata, 4116K rodata, 1044K init, 908K bss, 27296K reserved, 16384K cma-reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0de4fc0 (14196 kB)
[ 0.000000] .init : 0xc0de5000 - 0xc0eea000 (1044 kB)
[ 0.000000] .data : 0xc0eea000 - 0xc0fd9430 ( 958 kB)
[ 0.000000] .bss : 0xc0fd9430 - 0xc10bc510 ( 909 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] L2C: DT/platform modifies aux control register: 0x12086300 -> 0x1a086302
[ 0.000000] Aurora cache controller enabled, 4 ways, 256 kB
[ 0.000000] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302
[ 0.000014] sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 229681743818ns
[ 0.000718] Console: colour dummy device 80x30
[ 0.000740] Calibrating delay loop... 1195.21 BogoMIPS (lpj=2988032)
[ 0.060093] pid_max: default: 32768 minimum: 301
[ 0.060191] Security Framework initialized
[ 0.060334] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.060345] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.060926] Initializing cgroup subsys blkio
[ 0.060943] Initializing cgroup subsys memory
[ 0.060974] Initializing cgroup subsys devices
[ 0.060986] Initializing cgroup subsys freezer
[ 0.060997] Initializing cgroup subsys net_cls
[ 0.061008] Initializing cgroup subsys perf_event
[ 0.061020] Initializing cgroup subsys net_prio
[ 0.061069] CPU: Testing write buffer coherency: ok
[ 0.061097] ftrace: allocating 36930 entries in 109 pages
[ 0.117525] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.117608] Setting up static identity map for 0x90bac8 - 0x90bb60
[ 0.118001] mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1
[ 0.118129] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.119134] Brought up 1 CPUs
[ 0.119147] SMP: Total of 1 processors activated (1195.21 BogoMIPS).
[ 0.119154] CPU: All CPU(s) started in SVC mode.
[ 0.119639] devtmpfs: initialized
[ 0.120537] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.122213] xor: measuring software checksum speed
[ 0.170068] arm4regs : 1102.400 MB/sec
[ 0.220070] 8regs : 928.000 MB/sec
[ 0.270065] 32regs : 1114.400 MB/sec
[ 0.270073] xor: using function: 32regs (1114.400 MB/sec)
[ 0.270226] pinctrl core: initialized pinctrl subsystem
[ 0.273924] NET: Registered protocol family 16
[ 0.275580] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.282761] No ATAGs?
[ 0.282781] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.283979] Serial: AMBA PL011 UART driver
[ 0.375480] raid6: int32x1 135 MB/s
[ 0.460084] raid6: int32x2 225 MB/s
[ 0.545089] raid6: int32x4 199 MB/s
[ 0.630354] raid6: int32x8 206 MB/s
[ 0.630362] raid6: using algorithm int32x2 (225 MB/s)
[ 0.630368] raid6: using intx1 recovery algorithm
[ 0.634160] vgaarb: loaded
[ 0.634984] SCSI subsystem initialized
[ 0.635509] usbcore: registered new interface driver usbfs
[ 0.635565] usbcore: registered new interface driver hub
[ 0.635642] usbcore: registered new device driver usb
[ 0.636640] media: Linux media interface: v0.10
[ 0.636691] Linux video capture interface: v2.00
[ 0.636771] pps_core: LinuxPPS API ver. 1 registered
[ 0.636778] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.636801] PTP clock support registered
[ 0.636871] EDAC MC: Ver: 3.0.0
[ 0.637868] Advanced Linux Sound Architecture Driver Initialized.
[ 0.638437] NetLabel: Initializing
[ 0.638445] NetLabel: domain hash size = 128
[ 0.638450] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.638499] NetLabel: unlabeled traffic allowed by default
[ 0.638753] Switched to clocksource armada_370_xp_clocksource
[ 0.692501] NET: Registered protocol family 2
[ 0.693256] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.693314] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.693391] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.693457] TCP: reno registered
[ 0.693469] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.693492] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.693654] NET: Registered protocol family 1
[ 0.694012] RPC: Registered named UNIX socket transport module.
[ 0.694022] RPC: Registered udp transport module.
[ 0.694028] RPC: Registered tcp transport module.
[ 0.694033] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.696231] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.703133] zpool: loaded
[ 0.703149] zbud: loaded
[ 0.703656] VFS: Disk quotas dquot_6.5.2
[ 0.703915] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.705463] NFS: Registering the id_resolver key type
[ 0.705506] Key type id_resolver registered
[ 0.705513] Key type id_legacy registered
[ 0.705537] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.708026] bounce: pool size: 64 pages
[ 0.708204] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.708370] io scheduler noop registered
[ 0.708385] io scheduler deadline registered
[ 0.708543] io scheduler cfq registered (default)
[ 0.711256] armada-370-pinctrl d0018000.pin-ctrl: registered pinctrl driver
[ 0.713018] irq: Cannot allocate irq_descs @ IRQ40, assuming pre-allocated
[ 0.713383] irq: Cannot allocate irq_descs @ IRQ72, assuming pre-allocated
[ 0.713613] irq: Cannot allocate irq_descs @ IRQ104, assuming pre-allocated
[ 0.714613] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[ 0.714631] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 0.714642] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 0.714653] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.715093] PCI: bus0: Fast back to back transfers disabled
[ 0.715105] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.715118] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.715247] PCI: bus1: Fast back to back transfers enabled
[ 0.715818] PCI: bus2: Fast back to back transfers disabled
[ 0.715922] pci 0000:00:02.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff]
[ 0.715935] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.715955] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8000000-0xf800ffff 64bit]
[ 0.715979] pci 0000:02:00.0: BAR 2: assigned [mem 0xf8010000-0xf8010fff 64bit]
[ 0.716001] pci 0000:02:00.0: BAR 4: assigned [mem 0xf8011000-0xf8011fff 64bit]
[ 0.716020] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.716031] pci 0000:00:02.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 0.716157] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 0.717426] mv_xor d0060800.xor: Marvell shared XOR driver
[ 0.738855] mv_xor d0060800.xor: Marvell XOR: ( xor cpy )
[ 0.763841] mv_xor d0060800.xor: Marvell XOR: ( xor cpy )
[ 0.763994] mv_xor d0060900.xor: Marvell shared XOR driver
[ 0.788838] mv_xor d0060900.xor: Marvell XOR: ( xor cpy )
[ 0.813839] mv_xor d0060900.xor: Marvell XOR: ( xor cpy )
[ 0.871239] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 0.873531] console [ttyS0] disabled
[ 0.893681] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 19, base_baud = 12500000) is a 16550A
[ 1.741560] console [ttyS0] enabled
[ 1.745474] Serial: AMBA driver
[ 1.749741] [drm] Initialized drm 1.1.0 20060810
[ 1.759933] loop: module loaded
[ 1.764062] Loading iSCSI transport class v2.0-870.
[ 1.769375] iscsi: registered transport (tcp)
[ 1.775339] pxa3xx-nand d00d0000.nand: This platform can't do DMA on this device
[ 1.783107] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x38
[ 1.789514] nand: Micron MT29F8G08ABABAWP
[ 1.793545] nand: 1024 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224
[ 1.801342] pxa3xx-nand d00d0000.nand: ECC strength 16, ECC step size 2048
[ 1.808828] Bad block table found at page 262016, version 0x01
[ 1.815439] Bad block table found at page 261888, version 0x01
[ 1.821787] 3 ofpart partitions found on MTD device pxa3xx_nand-0
[ 1.827929] Creating 3 MTD partitions on "pxa3xx_nand-0":
[ 1.833371] 0x000000000000-0x000000400000 : "U-Boot"
[ 1.839333] 0x000000400000-0x000000800000 : "Linux"
[ 1.845119] 0x000000800000-0x000040000000 : "Filesystem"
[ 1.854321] libphy: orion_mdio_bus: probed
[ 1.860953] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 1.866476] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1
[ 1.874772] xhci_hcd 0000:02:00.0: hcc params 0x200073a9 hci version 0x100 quirks 0x00000010
[ 1.883676] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.890536] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.897810] usb usb1: Product: xHCI Host Controller
[ 1.902725] usb usb1: Manufacturer: Linux 4.0.5-2-ARCH xhci-hcd
[ 1.908685] usb usb1: SerialNumber: 0000:02:00.0
[ 1.914019] hub 1-0:1.0: USB hub found
[ 1.917828] hub 1-0:1.0: 2 ports detected
[ 1.922379] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 1.927868] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 2
[ 1.935509] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.942352] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.949623] usb usb2: Product: xHCI Host Controller
[ 1.954538] usb usb2: Manufacturer: Linux 4.0.5-2-ARCH xhci-hcd
[ 1.960498] usb usb2: SerialNumber: 0000:02:00.0
[ 1.965712] hub 2-0:1.0: USB hub found
[ 1.969568] hub 2-0:1.0: 2 ports detected
[ 1.974398] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.981026] ehci-pci: EHCI PCI platform driver
[ 1.985574] ehci-platform: EHCI generic platform driver
[ 1.990974] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 1.996395] ehci-omap: OMAP-EHCI Host Controller driver
[ 2.001749] ehci-orion: EHCI orion driver
[ 2.005941] orion-ehci d0050000.usb: EHCI Host Controller
[ 2.011609] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 3
[ 2.019582] orion-ehci d0050000.usb: irq 25, io mem 0xd0050000
[ 2.033776] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00
[ 2.039905] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.046749] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.054021] usb usb3: Product: EHCI Host Controller
[ 2.058936] usb usb3: Manufacturer: Linux 4.0.5-2-ARCH ehci_hcd
[ 2.064895] usb usb3: SerialNumber: d0050000.usb
[ 2.070123] hub 3-0:1.0: USB hub found
[ 2.074161] hub 3-0:1.0: 1 port detected
[ 2.078543] orion-ehci d0051000.usb: EHCI Host Controller
[ 2.084246] orion-ehci d0051000.usb: new USB bus registered, assigned bus number 4
[ 2.092066] orion-ehci d0051000.usb: irq 26, io mem 0xd0051000
[ 2.103772] orion-ehci d0051000.usb: USB 2.0 started, EHCI 1.00
[ 2.109891] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.116735] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.124008] usb usb4: Product: EHCI Host Controller
[ 2.128921] usb usb4: Manufacturer: Linux 4.0.5-2-ARCH ehci_hcd
[ 2.134881] usb usb4: SerialNumber: d0051000.usb
[ 2.140083] hub 4-0:1.0: USB hub found
[ 2.143938] hub 4-0:1.0: 1 port detected
[ 2.148312] ehci-exynos: EHCI EXYNOS driver
[ 2.152724] tegra-ehci: Tegra EHCI driver
[ 2.156913] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.163169] ohci-pci: OHCI PCI platform driver
[ 2.167726] ohci-platform: OHCI generic platform driver
[ 2.173105] ohci-exynos: OHCI EXYNOS driver
[ 2.177535] ohci-omap3: OHCI OMAP3 driver
[ 2.181746] usbcore: registered new interface driver uas
[ 2.187267] usbcore: registered new interface driver usb-storage
[ 2.193369] usbcore: registered new interface driver ums-cypress
[ 2.199470] usbcore: registered new interface driver ums_eneub6250
[ 2.205741] usbcore: registered new interface driver ums-freecom
[ 2.211839] usbcore: registered new interface driver ums-isd200
[ 2.217849] usbcore: registered new interface driver ums-usbat
[ 2.226901] rtc-mv d0010300.rtc: rtc core: registered d0010300.rtc as rtc0
[ 2.234926] i2c /dev entries driver
[ 2.239467] pca953x 0-0025: failed reading register
[ 2.258150] orion_wdt: Initial timeout 229 sec, nowayout
[ 2.264606] Driver 'mmcblk' needs updating - please use bus_type methods
[ 2.271409] sdhci: Secure Digital Host Controller Interface driver
[ 2.277646] sdhci: Copyright(c) Pierre Ossman
[ 2.308860] Synopsys Designware Multimedia Card Interface Driver
[ 2.318552] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.325387] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.332214] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.338349] usbcore: registered new interface driver usbhid
[ 2.344003] usbhid: USB HID core driver
[ 2.349418] ashmem: initialized
[ 2.355267] oprofile: no performance counters
[ 2.359818] oprofile: using timer interrupt.
[ 2.364373] TCP: cubic registered
[ 2.368281] NET: Registered protocol family 10
[ 2.373763] mip6: Mobile IPv6
[ 2.376761] NET: Registered protocol family 17
[ 2.381434] Key type dns_resolver registered
[ 2.385954] ThumbEE CPU extension supported.
[ 2.391363] usb 3-1: new high-speed USB device number 2 using orion-ehci
[ 2.400167] Registering SWP/SWPB emulation handler
[ 2.406045] registered taskstats version 1
[ 2.413836] Btrfs loaded
[ 2.417518] rtc-mv d0010300.rtc: setting system clock to 2015-06-27 09:27:36 UTC (1435397256)
[ 2.426186] sr_init: No PMIC hook to init smartreflex
[ 2.431427] sr_init: platform driver register failed for SR
[ 2.438545] Unable to find PPMU node
[ 2.442202] exynos5-bus-int: probe of exynos5-bus-int failed with error -2
[ 2.449291] ALSA device list:
[ 2.452296] No soundcards found.
[ 2.456250] Waiting for root device /dev/sdb2...
[ 2.462120] usb 4-1: new high-speed USB device number 2 using orion-ehci
[ 2.534549] usb 3-1: New USB device found, idVendor=1a40, idProduct=0101
[ 2.541311] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.548505] usb 3-1: Product: USB 2.0 Hub
[ 2.553222] hub 3-1:1.0: USB hub found
[ 2.557174] hub 3-1:1.0: 4 ports detected
[ 2.599792] usb 4-1: New USB device found, idVendor=1286, idProduct=2042
[ 2.606555] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.613755] usb 4-1: Product: Bluetooth and Wireless LAN Composite Device
[ 2.620595] usb 4-1: Manufacturer: Marvell
[ 2.624726] usb 4-1: SerialNumber: 00117F67F607
[ 2.829041] usb 3-1.1: new high-speed USB device number 3 using orion-ehci
[ 2.942782] usb 3-1.1: New USB device found, idVendor=05e3, idProduct=0723
[ 2.949717] usb 3-1.1: New USB device strings: Mfr=3, Product=4, SerialNumber=0
[ 2.957088] usb 3-1.1: Product: USB Storage
[ 2.961304] usb 3-1.1: Manufacturer: Generic
[ 2.966712] usb-storage 3-1.1:1.0: USB Mass Storage device detected
[ 2.973362] usb-storage 3-1.1:1.0: Quirks match for vid 05e3 pid 0723: 8000
[ 2.980482] scsi host0: usb-storage 3-1.1:1.0
[ 3.069031] usb 3-1.2: new high-speed USB device number 4 using orion-ehci
[ 3.182650] usb 3-1.2: New USB device found, idVendor=05e3, idProduct=0723
[ 3.189584] usb 3-1.2: New USB device strings: Mfr=3, Product=4, SerialNumber=0
[ 3.196962] usb 3-1.2: Product: USB Storage
[ 3.201181] usb 3-1.2: Manufacturer: Generic
[ 3.206706] usb-storage 3-1.2:1.0: USB Mass Storage device detected
[ 3.213260] usb-storage 3-1.2:1.0: Quirks match for vid 05e3 pid 0723: 8000
[ 3.220363] scsi host1: usb-storage 3-1.2:1.0
[ 3.985483] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 9451 PQ: 0 ANSI: 0
[ 3.994581] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.002935] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 4.225332] scsi 1:0:0:0: Direct-Access Generic STORAGE DEVICE 9451 PQ: 0 ANSI: 0
[ 4.234390] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 4.448520] sd 1:0:0:0: [sdb] 15628288 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 4.457265] sd 1:0:0:0: [sdb] Write Protect is off
[ 4.463264] sd 1:0:0:0: [sdb] No Caching mode page found
[ 4.468638] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 4.480694] sdb: sdb1 sdb2
[ 4.487265] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 4.580679] EXT4-fs (sdb2): couldn't mount as ext3 due to feature incompatibilities
[ 4.589915] EXT4-fs (sdb2): couldn't mount as ext2 due to feature incompatibilities
[ 4.617630] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.625417] VFS: Mounted root (ext4 filesystem) on device 8:18.
[ 4.635910] devtmpfs: mounted
[ 4.640039] Freeing unused kernel memory: 1044K (c0de5000 - c0eea000)
[ 5.111345] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.116813] systemd[1]: Inserted module 'ip_tables'
[ 5.136994] random: systemd urandom read with 40 bits of entropy available
[ 5.153148] systemd[1]: systemd 221 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD +IDN)
[ 5.171831] systemd[1]: Detected architecture arm.

Welcome to Arch Linux ARM!

[ 5.200553] systemd[1]: Set hostname to <dog>.
[ 6.096475] systemd[1]: display-manager.service: Cannot add dependency job, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ OK ] Reached target Remote File Systems.
[ 6.128926] systemd[1]: Reached target Remote File Systems.
[ 6.134728] systemd[1]: Starting Remote File Systems.
[ OK ] Created slice Root Slice.
[ 6.153912] systemd[1]: Created slice Root Slice.
[ 6.158833] systemd[1]: Starting Root Slice.
[ OK ] Created slice User and Session Slice.
[ 6.173912] systemd[1]: Created slice User and Session Slice.
[ 6.179866] systemd[1]: Starting User and Session Slice.
[ OK ] Listening on udev Kernel Socket.
[ 6.198910] systemd[1]: Listening on udev Kernel Socket.
[ 6.204424] systemd[1]: Starting udev Kernel Socket.
[ 6.242137] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on Journal Socket.
[ 6.258923] systemd[1]: Listening on Journal Socket.
[ 6.264151] systemd[1]: Starting Journal Socket.
[ OK ] Listening on udev Control Socket.
[ 6.278911] systemd[1]: Listening on udev Control Socket.
[ 6.284518] systemd[1]: Starting udev Control Socket.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 6.303905] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 6.311076] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ OK ] Created slice System Slice.
[ 6.328913] systemd[1]: Created slice System Slice.
[ 6.334047] systemd[1]: Starting System Slice.
[ 6.341730] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 6.378970] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 6.389095] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 6.407876] systemd[1]: Mounting Temporary Directory...
Mounting Temporary Directory...
[ OK ] Reached target Slices.
[ 6.443998] systemd[1]: Reached target Slices.
[ 6.448633] systemd[1]: Starting Slices.
[ 6.462984] systemd[1]: Starting Create list of required static device nodes for the current kernel...
Starting Create list of required st... nodes for the current kernel...
[ OK ] Created slice system-netctl.slice.
[ 6.508900] systemd[1]: Created slice system-netctl.slice.
[ 6.514614] systemd[1]: Starting system-netctl.slice.
[ OK ] Reached target Encrypted Volumes.
[ 6.533918] systemd[1]: Reached target Encrypted Volumes.
[ 6.539508] systemd[1]: Starting Encrypted Volumes.
[ 6.544962] systemd[1]: Mounted Huge Pages File System.
[ 6.550725] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 6.558887] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 6.570080] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 6.594282] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 6.602145] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 6.613220] systemd[1]: Mounting Debug File System...
Mounting Debug File System...
[ OK ] Listening on Device-mapper event daemon FIFOs.
[ 6.648912] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 6.655701] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ OK ] Set up automount Arbitrary Executab...ats File System Automount Point.
[ 6.678911] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 6.688564] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 6.701188] systemd[1]: Started Load Kernel Modules.
[ 6.709760] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 6.729476] systemd[1]: Mounted Configuration File System.
[ OK ] Listening on Journal Socket (/dev/log).
[ 6.749034] systemd[1]: Listening on Journal Socket (/dev/log).
[ 6.759019] systemd[1]: Starting Journal Socket (/dev/log).
[ 6.770554] systemd[1]: Started Set Up Additional Binary Formats.
[ OK ] Reached target Swap.
[ 6.782488] systemd[1]: Reached target Swap.
[ 6.792724] systemd[1]: Starting Swap.
[ OK ] Listening on LVM2 metadata daemon socket.
[ 6.808922] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 6.815227] systemd[1]: Starting LVM2 metadata daemon socket.
[ 6.824546] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 6.847672] systemd[1]: Starting Setup Virtual Console...
Starting Setup Virtual Console...
[ 6.869139] systemd[1]: Mounted FUSE Control File System.
[ OK ] Created slice system-getty.slice.
[ 6.893997] systemd[1]: Created slice system-getty.slice.
[ 6.904333] systemd[1]: Starting system-getty.slice.
[ OK ] Reached target Paths.
[ 6.918934] systemd[1]: Reached target Paths.
[ 6.923685] systemd[1]: Starting Paths.
[ OK ] Mounted POSIX Message Queue File System.
[ 6.945067] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted Debug File System.
[ 6.963937] systemd[1]: Mounted Debug File System.
[ OK ] Mounted Temporary Directory.
[ 6.979004] systemd[1]: Mounted Temporary Directory.
[ OK ] Started Remount Root and Kernel File Systems.
[ 6.999019] systemd[1]: Started Remount Root and Kernel File Systems.
[ OK ] Started Create list of required sta...ce nodes for the current kernel.
[ 7.028987] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ OK ] Started Apply Kernel Variables.
[ 7.054169] systemd[1]: Started Apply Kernel Variables.
[ OK ] Started Setup Virtual Console.
[ 7.078971] systemd[1]: Started Setup Virtual Console.
[ 7.336630] systemd[1]: Started Rebuild Dynamic Linker Cache.
[ 7.343325] systemd[1]: Started First Boot Wizard.
[ 7.348523] systemd[1]: Started Create System Users.
[ 7.358339] systemd[1]: Starting Create Static Device Nodes in /dev...
Starting Create Static Device Nodes in /dev...
[ 7.376891] random: nonblocking pool is initialized
[ 7.413250] systemd[1]: Started Rebuild Hardware Database.
[ 7.422485] systemd[1]: Starting udev Coldplug all Devices...
Starting udev Coldplug all Devices...
[ 7.460800] systemd[1]: Starting Load/Save Random Seed...
Starting Load/Save Random Seed...
[ OK ] Started Load/Save Random Seed.
[ 7.579068] systemd[1]: Started Load/Save Random Seed.
[ OK ] Started Create Static Device Nodes in /dev.
[ 7.694008] systemd[1]: Started Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
[ 7.803990] systemd[1]: Reached target Local File Systems (Pre).
[ 7.819018] systemd[1]: Starting Local File Systems (Pre).
[ 7.839114] systemd[1]: Mounted Virtual Machine and Container Storage.
[ 7.862314] systemd[1]: Starting udev Kernel Device Manager...
Starting udev Kernel Device Manager...
[ OK ] Started udev Kernel Device Manager.
[ 8.084010] systemd[1]: Started udev Kernel Device Manager.
[ OK ] Started Journal Service.
[ 8.383987] systemd[1]: Started Journal Service.
Starting Flush Journal to Persistent Storage...
[ 8.531086] systemd-journald[97]: Received request to flush runtime journal from PID 1
[ OK ] Started udev Coldplug all Devices.
[ OK ] Found device /dev/ttyS0.
[ 11.409853] mvneta d0070000.ethernet eth0: Using device tree mac address 00:50:43:ee:28:19
[ 11.500963] mvneta d0074000.ethernet eth1: Using device tree mac address 00:50:43:26:28:19
[ 12.396262] Bluetooth: Core ver 2.20
[ 12.434192] NET: Registered protocol family 31
[ 12.438710] Bluetooth: HCI device and connection manager initialized
[ 12.500524] cfg80211: Calling CRDA to update world regulatory domain
[ 12.517483] Bluetooth: HCI socket layer initialized
[ 12.554184] Bluetooth: L2CAP socket layer initialized
[ OK ] Found device STORAGE_DEVICE 1.
[ 12.605664] Bluetooth: SCO socket layer initialized
Mounting /boot...
[ 12.712933] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 12.725948] mwifiex: rx work enabled, cpus 1
[ OK ] Mounted /boot.
[ OK ] Reached target Local File Systems.
[ 12.796127] usbcore: registered new interface driver mwifiex_usb
[ 12.817281] usbcore: registered new interface driver btusb
[ 12.848376] usb 4-1: WLAN FW is active
[ 12.974993] ieee80211 phy0: ignoring F/W country code US
[ 13.001604] usb 4-1: driver_version = mwifiex 1.0 (14.68.22.p16)
[ OK ] Started Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories...
[ OK ] Started Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Timers.
[ OK ] Reached target Basic System.
[ OK ] Started Entropy Harvesting Daemon.
Starting Entropy Harvesting Daemon...
Starting Packet Filtering Framework...
Starting Login Service...
[ OK ] Started D-Bus System Message Bus.
[ 14.041671] nf_conntrack version 0.5.0 (15973 buckets, 63892 max)
Starting D-Bus System Message Bus...
[ INFO ] Network Service is not active.
[DEPEND] Dependency failed for Wait for Network to be Configured.
Starting Permit User Sessions...
[ OK ] Started Permit User Sessions.
[ OK ] Started Login Service.
[ OK ] Started Getty on tty1.
Starting Getty on tty1...
[ OK ] Started Serial Getty on ttyS0.
Starting Serial Getty on ttyS0...
[ OK ] Reached target Login Prompts.
[ OK ] Started Packet Filtering Framework.
[ OK ] Found device /sys/subsystem/net/devices/eth0.
[ OK ] Found device /sys/subsystem/net/devices/eth1.
[ OK ] Created slice system-systemd\x2drfkill.slice.
Starting Load/Save RF Kill Switch Status of rfkill0...
Starting Protected home network...
Starting Connection to home hub...
[ OK ] Reached target Bluetooth.
[ 18.762116] cfg80211: World regulatory domain updated:
[ 18.767408] cfg80211: DFS Master region: unset
[ 18.771819] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 18.781653] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.789723] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.797791] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.805851] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 18.815395] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 18.824936] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 18.833084] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 18.841141] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ OK ] Started Load/Save RF Kill Switch Status of rfkill0.
Starting Load/Save RF Kill Switch Status of rfkill1...
[ OK ] Started Load/Save RF Kill Switch Status of rfkill1.
[ 19.201471] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 19.227210] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.251360] cfg80211: Calling CRDA for country: DE
[ 19.306845] cfg80211: Regulatory domain changed to country: DE
[ 19.312775] cfg80211: DFS Master region: ETSI
[ 19.317094] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 19.326910] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.334970] cfg80211: (5150000 KHz - 5250000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 19.344511] cfg80211: (5250000 KHz - 5350000 KHz @ 80000 KHz, 200000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 19.354059] cfg80211: (5470000 KHz - 5725000 KHz @ 160000 KHz), (N/A, 2698 mBm), (0 s)
[ 19.362203] cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)

Arch Linux 4.0.5-2-ARCH (ttyS0)

dog login: [ 24.224204] mvneta d0070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 24.232125] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

Arch Linux 4.0.5-2-ARCH (ttyS0)

Last login: Sat Jun 27 11:26:29 on ttyS0
[root@dog ~]# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 532
link/ether 00:50:43:ee:28:19 brd ff:ff:ff:ff:ff:ff
inet 192.168.2.4/26 brd 192.168.2.63 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::250:43ff:feee:2819/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default qlen 532
link/ether 00:50:43:26:28:19 brd ff:ff:ff:ff:ff:ff
4: mlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:11:7f:67:f6:07 brd ff:ff:ff:ff:ff:ff
[root@dog ~]# ping 192.168.2.1
PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
64 bytes from 192.168.2.1: icmp_seq=1 ttl=64 time=2.55 ms
64 bytes from 192.168.2.1: icmp_seq=2 ttl=64 time=2.60 ms
64 bytes from 192.168.2.1: icmp_seq=3 ttl=64 time=2.58 ms

--- 192.168.2.1 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2003ms
')
shazled
 
Posts: 7
Joined: Tue Oct 07, 2014 9:39 pm

Re: Mirabox upgrade to 4.1.0-1 Kernel kills ethernet

Postby shazled » Mon Jun 29, 2015 8:04 pm

The problem persists with linux-armv7-4.1.0-2.
shazled
 
Posts: 7
Joined: Tue Oct 07, 2014 9:39 pm

Re: Mirabox upgrade to 4.1.0-1 Kernel kills ethernet

Postby metrolan » Sun Jul 12, 2015 1:00 pm

With 4.1.1 still no ethernet.

Any ideas?
metrolan
 
Posts: 6
Joined: Sat May 16, 2015 4:48 pm

Re: Mirabox upgrade to 4.1.0-1 Kernel kills ethernet

Postby metrolan » Sun Jul 12, 2015 5:35 pm

@shazled, if you need it, I have a december 2014 ArchlinuxARM-mirabox, working OK.
metrolan
 
Posts: 6
Joined: Sat May 16, 2015 4:48 pm


Return to Marvell

Who is online

Users browsing this forum: No registered users and 5 guests