@moonman I'm using the last available version from here
http://os.archlinuxarm.org/os/ArchLinux ... est.tar.gz but i found no clues about the kernel version so far.
Also, i did attach a console and below are my findings
During the first attempt (bellow) if figured out that the installations steps where not updated.
At step 9 on page
https://archlinuxarm.org/platforms/armv ... /odroid-xu there should be a recursive copy.
$this->bbcode_second_pass_code('', '
reading dtbs/exynos5410-odroidxu.dtb
** Unable to read "dtbs/exynos5410-odroidxu.dtb" from mmc 0:1 **
Starting kernel ...
')
I fixed the boot partition, and apparently it gets stuck at Starting kernel message. (but now it reads the dbt file).
What i found disturbing are the messages:
$this->bbcode_second_pass_code('', '** Unable to read "u-boot.bin" from mmc 0:1 ** ')
and
$this->bbcode_second_pass_code('', 'eMMC OPEN Failed.!!')
Full boot sequence below:
$this->bbcode_second_pass_code('', '
U-Boot 2012.07 (Sep 13 2013 - 13:53:58) for Exynos5410
CPU: Exynos5410 Rev2.3 [Samsung SOC on SMP Platform Base on ARM CortexA15]
APLL = 900MHz, KPLL = 600MHz
MPLL = 532MHz, BPLL = 800MHz
DRAM: 2 GiB
WARNING: Caches not enabled
TrustZone Enabled BSP
BL1 version:
PMIC VER : 0, CHIP REV : 6
VDD MIF : 1.00000V
VDD ARM : 1.00000V
VDD INT : 1.00000V
VDD G3D : 1.00000V
VDD KFC : 1.00000V
Checking Boot Mode ... SDMMC
MMC: S5P_MSHC2: 0, S5P_MSHC0: 1
MMC Device 0: 29.7 GiB
MMC Device 1: [ERROR] response error : 00000006 cmd 8
[ERROR] response error : 00000006 cmd 55
[ERROR] response error : 00000006 cmd 2
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Press 'Enter' or 'Space' to stop autoboot: 0
there are pending interrupts 0x00000001
reading boot.ini
5234 bytes read
Find boot.ini file from FAT Area!!
boot.ini command = setenv hk_current_version "2"
boot.ini command = setenv verify 'if test $hk_version != $hk_current_version;then;fatload mmc 0:1 40008000 u-boot.bin;emmc open 0;movi w z u 0 40008000;emmc close 0;setenv hk_version $hk_c'
boot.ini command = run verify
reading u-boot.bin
** Unable to read "u-boot.bin" from mmc 0:1 **
[ERROR] response timeout error : 00000104 cmd 6
eMMC OPEN Failed.!!
boot.ini command = setenv initrd_high "0xffffffff"
boot.ini command = setenv fdt_high "0xffffffff"
boot.ini command = setenv bootrootfs "console=ttySAC2,115200n8 root=/dev/mmcblk1p2 rootwait rw"
boot.ini command = setenv fb_x_res "1920"
boot.ini command = setenv fb_y_res "1080"
boot.ini command = setenv vout "hdmi"
boot.ini command = setenv left "56"
boot.ini command = setenv right "24"
boot.ini command = setenv upper "3"
boot.ini command = setenv lower "3"
boot.ini command = setenv hsync "14"
boot.ini command = setenv vsync "3"
boot.ini command = setenv fb_control "left=${left} right=${right} upper=${upper} lower=${lower} vsync=${vsync} hsync=${hsync}"
boot.ini command = setenv hdmi_phy_res "1080p60hz"
boot.ini command = setenv led_blink "1"
boot.ini command = setenv bootcmd "fatload mmc 0:1 0x40008000 zImage; if fatload mmc 0:1 0x41f00000 dtbs/exynos5410-odroidxu.dtb; then bootz 0x40008000 - 0x41f00000; else bootz 0x40008000;"
boot.ini command = setenv bootargs "${bootrootfs} ${fb_control} fb_x_res=${fb_x_res} fb_y_res=${fb_y_res} vout=${vout} hdmi_phy_res=${hdmi_phy_res} led_blink=${led_blink}"
boot.ini command = boot
reading zImage
7126664 bytes read
reading dtbs/exynos5410-odroidxu.dtb
43935 bytes read
## Flattened Device Tree blob at 41f00000
Booting using the fdt blob at 0x41f00000
Using Device Tree in place at 41f00000, end 41f0db9e
Starting kernel ...
')
Thanks