Hi everyone.
I installed Archlinuxarm in the eMMC module, and can boot up from it with no problem. But when I plug in the TF card, U2 won't boot up until I remove it and reboot. The log came out from serial looks like this.
$this->bbcode_second_pass_code('', '[ 3.766483] VFS: Cannot open root device "mmcblk0p2" or unknown-block(179,2): error -6
[ 3.773978] Please append a correct "root=" boot option; here are the available partitions:')
It seems like a root partition problem. But I don't know where and how shall I put that "root=" to sovle it.
How can this be done? I want to use my TF card as well. Thank you.
This is the full log.
$this->bbcode_second_pass_code('', 'U-Boot 2010.12-svn (Jan 28 2013 - 14:10:19) for Exynox4412
CPU: S5PC220 [Samsung SOC on SMP Platform Base on ARM CortexA9]
APLL = 1000MHz, MPLL = 880MHz
DRAM: 2047 MiB
PMIC VERSION : 0x00, CHIP REV : 2
TrustZone Enabled BSP
BL1 version: 20121128
Checking Boot Mode ... EMMC4.41
REVISION: 2.0
Manufacturer TOSHIBA [ 7456MB ]
NAME: S5P_MSHC4
MMC Device 0: 7456 MB
MMC Device 1: 30207 MB
MMC Device 2 not found
ModeKey Check... run normal_boot
Net: No ethernet found.
Hit any key to stop autoboot: 0
NAME: S5P_MSHC4
NAME: S5P_MSHC4
>>> Load Boot Script from mmc 0:1 <<<
NAME: S5P_MSHC4
Partition1: Start Address(0x1000), Size(0x20000)
reading boot.scr
** Unable to read "boot.scr" from mmc 0:1 **
>>> Load Boot Script from mmc 0:2 <<<
NAME: S5P_MSHC4
Partition2: Start Address(0x21000), Size(0xe6f000)
reading boot.scr
** Unable to read "boot.scr" from mmc 0:2 **
NAME: S5P_MSHC4
Partition1: Start Address(0x1000), Size(0x20000)
reading zImage
2741112 bytes read
Boot with zImage
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0xa00
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 3.8.13.12-2-ARCH (root@root-chroot-copy) (gcc version 4.7.2 (GCC) ) #3 SMP PREEMPT Tue Nov 12 20:47:19 CST 2013 ()
[ 0.000000] Kernel was built at commit id ''
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: ODROIDU2
[ 0.000000] cma: CMA: reserved 64 MiB at 43000000
[ 0.000000] cma: CMA: reserved 64 MiB at 51000000
[ 0.000000] cma: CMA: reserved 128 MiB at 67800000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU EXYNOS4412 (id 0xe4412220)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] s3c_register_clksrc: clock armclk has no registers set
[ 0.000000] s3c_register_clksrc: clock audiocdclk has no registers set
[ 0.000000] audiocdclk: no parent clock specified
[ 0.000000] EXYNOS4: PLL settings, A=1000000000, M=880000000, E=96000000 V=350000000
[ 0.000000] EXYNOS4: ARMCLK=1000000000, DMC=440000000, ACLK200=176000000
[ 0.000000] ACLK100=110000000, ACLK160=176000000, ACLK133=146666666
[ 0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_cam0: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_cam1: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[ 0.000000] sclk_fimd: source is mout_mpll_user (6), rate is 55000000
[ 0.000000] sclk_mfc: source is mout_mfc0 (0), rate is 55000000
[ 0.000000] sclk_g3d: source is mout_g3d0 (0), rate is 55000000
[ 0.000000] Unable to set parent aclk_160 of clock dout_mmc0.
[ 0.000000] Unable to set parent aclk_160 of clock dout_mmc1.
[ 0.000000] Unable to set parent aclk_160 of clock dout_mmc2.
[ 0.000000] Running under secure firmware.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c179e000 s7936 r8192 d12544 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519938
[ 0.000000] Kernel command line: console=tty1 console=ttySAC1,115200 mem=2047M fbcon=map:1111111111111111111111111111 console=ttySAC1,115200 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait b_x_res=1280 fb_y_res=720 hdmi_phy_res=720
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Memory: 2047MB = 2047MB total
[ 0.000000] Memory: 1808320k/1808320k available, 287808k reserved, 1317888K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06b2a6c (6827 kB)
[ 0.000000] .init : 0xc06b3000 - 0xc06def00 ( 176 kB)
[ 0.000000] .data : 0xc06e0000 - 0xc074b360 ( 429 kB)
[ 0.000000] .bss : 0xc074b360 - 0xc07883e0 ( 245 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:549
[ 0.000000] MCT clocksource init timer with clk_rate=24000000 hz
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty1] enabled
[ 0.000827] Calibrating delay loop... 1992.29 BogoMIPS (lpj=4980736)
[ 0.045057] pid_max: default: 32768 minimum: 301
[ 0.045329] Mount-cache hash table entries: 512
[ 0.046287] Initializing cgroup subsys cpuacct
[ 0.046324] Initializing cgroup subsys devices
[ 0.046382] CPU: Testing write buffer coherency: ok
[ 0.046688] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[ 0.046805] Setting up static identity map for 0x404f0ac0 - 0x404f0b18
[ 0.046878] L310 cache controller enabled
[ 0.046904] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x7e470001, Cache size: 1048576 B
[ 0.097028] CPU1: Booted secondary processor
[ 0.116740] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[ 0.127016] CPU2: Booted secondary processor
[ 0.146740] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
[ 0.157032] CPU3: Booted secondary processor
[ 0.176740] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
[ 0.176769] Brought up 4 CPUs
[ 0.176841] SMP: Total of 4 processors activated (7969.17 BogoMIPS).
[ 0.177564] devtmpfs: initialized
[ 0.183308] regulator-dummy: no parameters
[ 0.190415] NET: Registered protocol family 16
[ 0.198497] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.200434] s5p_hdmi_cec_set_platdata()
[ 0.202108] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.202131] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.202215] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.202290] EXYNOS4x12 PMU Initialize
[ 0.203107] EXYNOS: Initializing architecture
[ 0.203498] s3c24xx-pwm s3c24xx-pwm.0: tin at 110000000, tdiv at 110000000, tin=divclk, base 0
[ 0.203571] s3c24xx-pwm s3c24xx-pwm.1: tin at 110000000, tdiv at 110000000, tin=divclk, base 8
[ 0.208831] bio: create slab <bio-0> at 0
[ 0.209139] hdmi_5v: 5000 mV
[ 0.209461] SCSI subsystem initialized
[ 0.209674] usbcore: registered new interface driver usbfs
[ 0.209728] usbcore: registered new interface driver hub
[ 0.209798] usbcore: registered new device driver usb
[ 0.209931] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.209953] s3c-i2c s3c2440-i2c.0: bus frequency set to 71 KHz
[ 0.211750] max77686 0-0009: device found
[ 0.211839] max77686 0-0009: irq is not specified
[ 0.236746] LDO1 VDD_ALIVE: 1000 mV
[ 0.266746] LDO2 VDDQ_M1_1V8: 1200 mV
[ 0.296746] LDO3 VDDQ_AUD_1V8: 1800 mV
[ 0.326746] LDO4 VDDQ_MMC2_2V8: 2800 mV
[ 0.356747] LDO5 VDDQ_MMC1_1V8: 1800 mV
[ 0.391748] LDO6 VDD10_MPLL_1V0: 1000 mV
[ 0.426748] LDO7 VDD10_EPLL_1V0: 1000 mV
[ 0.456749] LDO8 VDD10_MIPI_1V0: 1000 mV
[ 0.486747] LDO9 VT_CORE_1V0: ODROIDU2: Disabled regulator
[ 0.486765] LDO9 VT_CORE_1V0: 1000 mV
[ 0.506750] LDO10 VDD18_MIPI_1V8: 1800 mV
[ 0.536750] LDO11 VDD18_ABB1_1V8: 1800 mV
[ 0.556751] vdd_ldo12 range: 3300 mV
[ 0.586751] LDO13 VDD18_MIPIHSI_1V8: 1800 mV
[ 0.616752] LDO14 VDD18_ADC_1V8: 1800 mV
[ 0.636752] vdd_ldo15 range: 1000 mV
[ 0.666752] LDO16 VDD18_HSIC: 1800 mV
[ 0.701752] LDO17 VDDQ_CAM_1V8: 1800 mV
[ 0.726751] LDO18 VDDQ_ISP_1V8: ODROIDU2: Disabled regulator
[ 0.726769] LDO18 VDDQ_ISP_1V8: 1800 mV
[ 0.736753] LDO19 VT_CAM_1V8: ODROIDU2: Disabled regulator
[ 0.736771] LDO19 VT_CAM_1V8: 1800 mV
[ 0.751754] LDO20 EMMC_IO_1V8: 1800 mV
[ 0.781754] LDO21 TFLASH_2V8: 2800 mV
[ 0.811754] LDO22 2V8: 2800 mV
[ 0.841753] LDO23 VDD_TOUCH_2V8: ODROIDU2: Disabled regulator
[ 0.841771] LDO23 VDD_TOUCH_2V8: 2800 mV
[ 0.871754] LDO24 VDD_TOUCHLED_3V3: ODROIDU2: Disabled regulator
[ 0.871772] LDO24 VDD_TOUCHLED_3V3: 3300 mV
[ 0.906756] LDO25 VDDQ_LCD_3V0: 1800 mV
[ 0.931755] LDO26 VDD_MOTOR_3V0: ODROIDU2: Disabled regulator
[ 0.931773] LDO26 VDD_MOTOR_3V0: 3000 mV
[ 0.941758] BUCK1 vdd_mif: 1100 mV
[ 0.956758] BUCK2 vdd_arm: 800 <--> 1500 mV at 1100 mV
[ 0.966758] BUCK3 vdd_int: 1125 mV
[ 0.981758] BUCK4 vdd_g3d: 850 <--> 1200 mV at 1000 mV
[ 1.011758] BUCK5 VDDQ_CKEM1_2: 1200 mV
[ 1.041758] BUCK6 1V35: 1350 mV
[ 1.071759] BUCK7 2V0: 2000 mV
[ 1.081759] ODROIDU2: Regulator BUCK8
[ 1.236761] BUCK8 3V0: 3300 mV
[ 1.261760] BUCK9 1V2: ODROIDU2: Disabled regulator
[ 1.261777] BUCK9 1V2: 1200 mV
[ 1.266922] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 1.266984] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 1.267005] s3c-i2c s3c2440-i2c.1: bus frequency set to 71 KHz
[ 1.267157] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 1.267217] s3c-i2c s3c2440-i2c.2: slave address 0x10
[ 1.267237] s3c-i2c s3c2440-i2c.2: bus frequency set to 71 KHz
[ 1.267379] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 1.267434] s3c-i2c s3c2440-i2c.3: slave address 0x10
[ 1.267453] s3c-i2c s3c2440-i2c.3: bus frequency set to 71 KHz
[ 1.267550] s3c-i2c s3c2440-i2c.3: i2c-3: S3C I2C adapter
[ 1.267606] s3c-i2c s3c2440-i2c.7: slave address 0x10
[ 1.267626] s3c-i2c s3c2440-i2c.7: bus frequency set to 71 KHz
[ 1.267717] s3c-i2c s3c2440-i2c.7: i2c-7: S3C I2C adapter
[ 1.267788] s3c-i2c s3c2440-hdmiphy-i2c: slave address 0x10
[ 1.267808] s3c-i2c s3c2440-hdmiphy-i2c: bus frequency set to 71 KHz
[ 1.267953] s3c-i2c s3c2440-hdmiphy-i2c: i2c-8: S3C I2C adapter
[ 1.268005] media: Linux media interface: v0.10
[ 1.268051] Linux video capture interface: v2.00
[ 1.268273] Advanced Linux Sound Architecture Driver Initialized.
[ 1.268816] Switching to clocksource mct-frc
[ 1.275149] NET: Registered protocol family 2
[ 1.275590] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.275722] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[ 1.275883] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.275941] TCP: reno registered
[ 1.275961] UDP hash table entries: 512 (order: 2, 24576 bytes)
[ 1.276005] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[ 1.276217] NET: Registered protocol family 1
[ 1.276583] CPU PMU: probing PMU on CPU 0
[ 1.276609] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 1.277794] bounce pool size: 64 pages
[ 1.282064] VFS: Disk quotas dquot_6.5.2
[ 1.282307] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.284187] NILFS version 2 loaded
[ 1.285142] Btrfs loaded
[ 1.285310] msgmni has been set to 1469
[ 1.286237] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 1.286260] io scheduler noop registered
[ 1.286274] io scheduler deadline registered
[ 1.286410] io scheduler cfq registered (default)
[ 1.293666] s3c-fb exynos4-fb.0: start latency exceeded, new value 584 ns
[ 1.293718] s3c-fb exynos4-fb.0: state restore latency exceeded, new value 29084 ns
[ 1.302922] s3c-fb exynos4-fb.0: window 0: fb
[ 1.305459] dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-267056
[ 1.305481] dma-pl330 dma-pl330.0: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.307642] dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-267056
[ 1.307664] dma-pl330 dma-pl330.1: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 1.308439] dma-pl330 dma-pl330.2: Loaded driver for PL330 DMAC-267056
[ 1.308461] dma-pl330 dma-pl330.2: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[ 1.345404] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.346247] exynos4210-uart.0: ttySAC0 at MMIO 0x13800000 (irq = 84) is a S3C6400/10
[ 1.346474] exynos4210-uart.1: ttySAC1 at MMIO 0x13810000 (irq = 85) is a S3C6400/10
[ 2.387525] console [ttySAC1] enabled
[ 2.391382] exynos4210-uart.2: ttySAC2 at MMIO 0x13820000 (irq = 86) is a S3C6400/10
[ 2.399098] exynos4210-uart.3: ttySAC3 at MMIO 0x13830000 (irq = 87) is a S3C6400/10
[ 2.406928] [drm] Initialized drm 1.1.0 20060810
[ 2.411428] i2c i2c-2: attached s5p_ddc into i2c adapter successfully
[ 2.417679] i2c i2c-8: attached s5p_hdmiphy into i2c adapter successfully
[ 2.424650] exynos-mixer s5p-mixer: probe start
[ 2.429256] s5p-g2d s5p-g2d.0: The exynos g2d(ver 4.1) successfully probed
[ 2.436218] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 2.442348] [drm] No driver support for vblank timestamp query.
[ 2.448769] exynos-drm exynos-drm: No connectors reported connected with modes
[ 2.455451] [drm] Cannot find any crtc or sizes - going 1024x768
[ 2.475044] Console: switching to colour frame buffer device 128x48
[ 2.483070] exynos-drm exynos-drm: fb1: frame buffer device
[ 2.488704] exynos-drm exynos-drm: registered panic notifier
[ 2.494346] [drm] Initialized exynos 1.0.0 20110530 on minor 0
[ 2.500166] Mali<2>: Inserting Mali v19 device driver.
[ 2.505313] Mali<2>: Compiled: Nov 12 2013, time: 20:06:10.
[ 2.510884] Mali<2>: Driver revision:
[ 2.514572] Mali<2>: mali_module_init() registering driver
[ 2.520095] Mali<2>: mali_probe(): Called for platform device mali-utgard
[ 2.526850] Mali<2>: Memory system initializing
[ 2.531313] Mali<2>: Using device defined memory settings (dedicated: 0x00000000@0x00000000, shared: 0x10000000)
[ 2.541556] Mali<2>: Mali OS memory allocator created with max allocation size of 0x10000000 bytes, cpu_usage_adjust 0x00000000
[ 2.553022] Mali<2>: Using device defined frame buffer settings (0x00000000@0x00000000)
[ 2.564433] mali-utgard mali-utgard.0: start latency exceeded, new value 583 ns
[ 2.571775] mali-utgard mali-utgard.0: state restore latency exceeded, new value 3250 ns
[ 2.579806] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP0
[ 2.585465] Mali<2>: Mali PP: Base address of PP core: 0x13008000
[ 2.591579] Mali<2>: Found Mali GPU Mali-400 MP r1p1
[ 2.597595] Mali<2>: Mali L2 cache: Creating Mali L2 cache: Mali_L2
[ 2.602701] Mali<2>: Mali MMU: Creating Mali MMU: Mali_GP_MMU
[ 2.608416] Mali<2>: Mali GP: Creating Mali GP core: Mali_GP
[ 2.614010] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP0_MMU
[ 2.619795] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP0
[ 2.625450] Mali<2>: Mali PP: Base address of PP core: 0x13008000
[ 2.631508] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP1_MMU
[ 2.637264] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP1
[ 2.642932] Mali<2>: Mali PP: Base address of PP core: 0x1300a000
[ 2.649031] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP2_MMU
[ 2.654804] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP2
[ 2.660460] Mali<2>: Mali PP: Base address of PP core: 0x1300c000
[ 2.666538] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP3_MMU
[ 2.672289] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP3
[ 2.677981] Mali<2>: Mali PP: Base address of PP core: 0x1300e000
[ 2.684058] Mali<2>: 4+0 PP cores initialized
[ 2.688343] Mali<2>: Mali GPU Utilization: No utilization handler installed
[ 2.695336] Mali<2>: = clk_set_rate : 533 , 1000000
[ 2.700595] Mali<2>: = clk_get_rate: 533
[ 2.704130] Mali: init_mali_clock mali_clock c0707da8
[ 2.709889] Mali<1>: = regulator_enable -> use cnt: 1
[ 2.714350] Mali<2>: = regulator_set_voltage: 1125000, 1125000
[ 2.723642] Mali<1>: = regulator_get_voltage: 1125000
[ 2.726584] Mali<2>: MALI Clock is set at mali driver
[ 2.731071] Mali<2>: mali_probe(): Successfully initialized driver for platform device mali-utgard
[ 2.740028] mali-utgard mali-utgard.0: stop latency exceeded, new value 500 ns
[ 2.747296] mali-utgard mali-utgard.0: state save latency exceeded, new value 3792 ns
[ 2.755370] Mali: Mali device driver loaded
[ 2.759298] UMP: UMP device driver loaded
[ 2.768371] brd: module loaded
[ 2.773906] loop: module loaded
[ 2.776852] Loading iSCSI transport class v2.0-870.
[ 2.780024] iscsi: registered transport (tcp)
[ 2.783680] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.790203] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[ 2.795183] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 2.802473] s5p-ehci s5p-ehci: irq 102, io mem 0x12580000
[ 2.813881] s5p-ehci s5p-ehci: USB 2.0 started, EHCI 1.00
[ 2.816620] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.823074] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.830236] usb usb1: Product: S5P EHCI Host Controller
[ 2.835432] usb usb1: Manufacturer: Linux 3.8.13.12-2-ARCH ehci_hcd
[ 2.841696] usb usb1: SerialNumber: s5p-ehci
[ 2.846269] hub 1-0:1.0: USB hub found
[ 2.849665] hub 1-0:1.0: 3 ports detected
[ 2.853933] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.859888] exynos-ohci exynos-ohci: Already power on PHY
[ 2.865205] exynos-ohci exynos-ohci: EXYNOS OHCI Host Controller
[ 2.871211] exynos-ohci exynos-ohci: new USB bus registered, assigned bus number 2
[ 2.878834] exynos-ohci exynos-ohci: irq 102, io mem 0x12590000
[ 2.942919] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.946778] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.954009] usb usb2: Product: EXYNOS OHCI Host Controller
[ 2.959441] usb usb2: Manufacturer: Linux 3.8.13.12-2-ARCH ohci_hcd
[ 2.965704] usb usb2: SerialNumber: exynos-ohci
[ 2.970536] hub 2-0:1.0: USB hub found
[ 2.973922] hub 2-0:1.0: 3 ports detected
[ 2.978147] Initializing USB Mass Storage driver...
[ 2.982818] usbcore: registered new interface driver usb-storage
[ 2.988751] USB Mass Storage support registered.
[ 2.993346] usbcore: registered new interface driver ums-alauda
[ 2.999301] usbcore: registered new interface driver ums-cypress
[ 3.005247] usbcore: registered new interface driver ums-datafab
[ 3.011194] usbcore: registered new interface driver ums_eneub6250
[ 3.017328] usbcore: registered new interface driver ums-freecom
[ 3.023315] usbcore: registered new interface driver ums-isd200
[ 3.029176] usbcore: registered new interface driver ums-jumpshot
[ 3.035176] usbcore: registered new interface driver ums-realtek
[ 3.041054] usbcore: registered new interface driver ums-sddr09
[ 3.046911] usbcore: registered new interface driver ums-sddr55
[ 3.052729] usbcore: registered new interface driver ums-usbat
[ 3.161399] usb3503 0-0008: switched to HUB mode
[ 3.163728] usb3503 0-0008: usb3503_probe: probed on hub mode
[ 3.168580] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
[ 3.168887] usb 1-2: new high-speed USB device number 2 using s5p-ehci
[ 3.180706] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[ 3.187118] s5p-fimc exynos4-fimc.0: sclk_fimc rate is 176000000
[ 3.192596] s5p-fimc exynos4-fimc.0: start latency exceeded, new value 584 ns
[ 3.199700] s5p-fimc exynos4-fimc.0: state restore latency exceeded, new value 15416 ns
[ 3.207693] s5p-fimc exynos4-fimc.0: stop latency exceeded, new value 417 ns
[ 3.214728] s5p-fimc exynos4-fimc.0: state save latency exceeded, new value 2834 ns
[ 3.218935] s5p-fimc exynos4-fimc.1: sclk_fimc rate is 176000000
[ 3.228303] s5p-fimc exynos4-fimc.1: start latency exceeded, new value 417 ns
[ 3.235432] s5p-fimc exynos4-fimc.1: state restore latency exceeded, new value 15042 ns
[ 3.243414] s5p-fimc exynos4-fimc.1: stop latency exceeded, new value 459 ns
[ 3.250423] s5p-fimc exynos4-fimc.1: start latency exceeded, new value 459 ns
[ 3.253933] s5p-fimc exynos4-fimc.2: sclk_fimc rate is 176000000
[ 3.263535] s5p-fimc exynos4-fimc.1: state save latency exceeded, new value 2541 ns
[ 3.271195] s5p-fimc exynos4-fimc.2: start latency exceeded, new value 458 ns
[ 3.271217] s5p-fimc exynos4-fimc.2: state restore latency exceeded, new value 15375 ns
[ 3.271237] s5p-fimc exynos4-fimc.2: stop latency exceeded, new value 417 ns
[ 3.271248] s5p-fimc exynos4-fimc.2: state save latency exceeded, new value 2416 ns
[ 3.271315] s5p-fimc exynos4-fimc.3: sclk_fimc rate is 176000000
[ 3.271955] s5p-fimc exynos4-fimc.3: start latency exceeded, new value 417 ns
[ 3.271976] s5p-fimc exynos4-fimc.3: state restore latency exceeded, new value 15041 ns
[ 3.271994] s5p-fimc exynos4-fimc.3: stop latency exceeded, new value 417 ns
[ 3.272005] s5p-fimc exynos4-fimc.3: state save latency exceeded, new value 2333 ns
[ 3.272366] s5p-fimc-md: Registered fimc.0.m2m as /dev/video0
[ 3.272466] s5p-fimc-md: Registered fimc.0.capture as /dev/video1
[ 3.272560] s5p-fimc-md: Registered fimc.1.m2m as /dev/video2
[ 3.272658] s5p-fimc-md: Registered fimc.1.capture as /dev/video3
[ 3.272762] s5p-fimc-md: Registered fimc.2.m2m as /dev/video4
[ 3.272861] s5p-fimc-md: Registered fimc.2.capture as /dev/video5
[ 3.272956] s5p-fimc-md: Registered fimc.3.m2m as /dev/video6
[ 3.273049] s5p-fimc-md: Registered fimc.3.capture as /dev/video7
[ 3.273521] sclk_mfc rate is: 220
[ 3.273674] s5p-mfc s5p-mfc: decoder registered as /dev/video8
[ 3.273768] s5p-mfc s5p-mfc: encoder registered as /dev/video9
[ 3.274138] Exynos: Kernel Thermal management registered
[ 3.274317] cpuidle: using governor ladder
[ 3.274343] sdhci: Secure Digital Host Controller Interface driver
[ 3.274345] sdhci: Copyright(c) Pierre Ossman
[ 3.274423] s3c-sdhci exynos4-sdhci.2: clock source 2: mmc_busclk.2 (440000000 Hz)
[ 3.274486] mmc0: no vqmmc regulator found
[ 3.274493] mmc0: no vmmc regulator found
[ 3.303885] mmc0: SDHCI controller on samsung-hsmmc [exynos4-sdhci.2] using ADMA
[ 3.309200] usb 1-2: New USB device found, idVendor=0424, idProduct=9730
[ 3.309206] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.326588] mmc0: new high speed SDHC card at address 59b4
[ 3.326782] mmcblk0: mmc0:59b4 NCard 29.4 GiB
[ 3.327724] mmcblk0: p1
[ 3.468262] dw_mmc dw_mmc: Using internal DMA controller.
[ 3.473456] mmc1: no vmmc regulator found
[ 3.503886] dw_mmc dw_mmc: Version ID is 240a
[ 3.503890] DWMMC: Div 2 = 125
[ 3.503900] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[ 3.517993] dw_mmc dw_mmc: DW MMC controller at irq 109, 32 bit host data width, 128 deep fifo
[ 3.526983] usbcore: registered new interface driver usbhid
[ 3.532177] usbhid: USB HID core driver
[ 3.538894] usb 1-3: new high-speed USB device number 3 using s5p-ehci
[ 3.570813] max98090 1-0010: revision 0x43
[ 3.581137] [MAX98090] max98090_set_record_main_mic(150)
[ 3.587491] hkdk-snd-max89090 hkdk-snd-max89090: max98090-aif1 <-> samsung-i2s.0 mapping ok
[ 3.594427] mmc1: BKOPS_EN bit is not set
[ 3.599262] hkdk-snd-max89090 hkdk-snd-max89090: max98090-aif1 <-> samsung-i2s.0 mapping ok
[ 3.599591] DWMMC: Div 1 = 1
[ 3.599600] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 52000000Hz, actual 50000000HZ div = 1)
[ 3.600086] mmc1: new high speed DDR MMC card at address 0001
[ 3.600312] mmcblk1: mmc1:0001 008G92 7.28 GiB
[ 3.600400] mmcblk1boot0: mmc1:0001 008G92 partition 1 4.00 MiB
[ 3.600475] mmcblk1boot1: mmc1:0001 008G92 partition 2 4.00 MiB
[ 3.600548] mmcblk1rpmb: mmc1:0001 008G92 partition 3 512 KiB
[ 3.601502] mmcblk1: p1 p2
[ 3.602917] mmcblk1boot1: unknown partition table
[ 3.603953] mmcblk1boot0: unknown partition table
[ 3.659438] TCP: cubic registered
[ 3.662538] NET: Registered protocol family 17
[ 3.666251] NET: Registered protocol family 15
[ 3.669203] usb 1-3: New USB device found, idVendor=0424, idProduct=3503
[ 3.669210] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.669671] hub 1-3:1.0: USB hub found
[ 3.669823] hub 1-3:1.0: 3 ports detected
[ 3.692139] NET: Registered protocol family 35
[ 3.696855] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 3.704243] ThumbEE CPU extension supported.
[ 3.708492] Registering SWP/SWPB emulation handler
[ 3.716616] LDO20 EMMC_IO_1V8: incomplete constraints, leaving on
[ 3.721972] LDO10 VDD18_MIPI_1V8: incomplete constraints, leaving on
[ 3.727229] DRM: mali_platform_drm_probe()
[ 3.730528] mali_drm_init(), driver name: mali_drm, version 0.1
[ 3.736629] DRM: mali_driver_load()
[ 3.739905] [drm] Initialized mali_drm 0.1.0 20100520 on minor 1
[ 3.746033] s3c-rtc s3c64xx-rtc: setting system clock to 2000-01-01 03:25:13 UTC (946697113)
[ 3.758123] exynos4_dvfs_hotplug_init, max(2000000),min(0)
[ 3.760111] ALSA device list:
[ 3.762752] #0: Built-in Audio
[ 3.766483] VFS: Cannot open root device "mmcblk0p2" or unknown-block(179,2): error -6
[ 3.773978] Please append a correct "root=" boot option; here are the available partitions:
[ 3.782295] b300 30931968 mmcblk0 driver: mmcblk
[ 3.787501] b301 30930944 mmcblk0p1 000c4046-01
[ 3.792717] b308 7634944 mmcblk1 driver: mmcblk
[ 3.798024] b309 65536 mmcblk1p1 00000000-01
[ 3.803283] b30a 7567360 mmcblk1p2 00000000-02
[ 3.808537] b320 512 mmcblk1rpmb (driver?)
[ 3.813746] b318 4096 mmcblk1boot1 (driver?)
[ 3.819046] b310 4096 mmcblk1boot0 (driver?)
[ 3.824242] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,2)
[ 3.832724] [<c0014f60>] (unwind_backtrace+0x0/0xf8) from [<c04e76c8>] (panic+0x8c/0x1e4)
[ 3.840870] [<c04e76c8>] (panic+0x8c/0x1e4) from [<c06b4030>] (mount_block_root+0x1e4/0x29c)
[ 3.849266] [<c06b4030>] (mount_block_root+0x1e4/0x29c) from [<c06b439c>] (prepare_namespace+0x164/0x1c8)
[ 3.858832] [<c06b439c>] (prepare_namespace+0x164/0x1c8) from [<c04e3c5c>] (kernel_init+0x8/0xe4)
[ 3.867677] [<c04e3c5c>] (kernel_init+0x8/0xe4) from [<c000e3d8>] (ret_from_fork+0x14/0x3c)
[ 3.876021] CPU1: stopping
[ 3.878728] [<c0014f60>] (unwind_backtrace+0x0/0xf8) from [<c00135b0>] (handle_IPI+0x118/0x140)
[ 3.887477] [<c00135b0>] (handle_IPI+0x118/0x140) from [<c000855c>] (gic_handle_irq+0x60/0x68)
[ 3.896076] [<c000855c>] (gic_handle_irq+0x60/0x68) from [<c000df40>] (__irq_svc+0x40/0x70)
[ 3.904426] Exception stack(0xe706df40 to 0xe706df88)
[ 3.909483] df40: e706df88 3b9aca00 e6cc8e29 00000000 e6abb2de 00000000 c17a63f0 00000000
[ 3.917689] df60: c070b440 413fc090 c04f33ac 00000000 00000018 e706df88 c00566a0 c03ec3d4
[ 3.925860] df80: 60000153 ffffffff
[ 3.929343] [<c000df40>] (__irq_svc+0x40/0x70) from [<c03ec3d4>] (cpuidle_wrap_enter+0x48/0x94)
[ 3.938075] [<c03ec3d4>] (cpuidle_wrap_enter+0x48/0x94) from [<c03ec0dc>] (cpuidle_enter_state+0x14/0x68)
[ 3.947657] [<c03ec0dc>] (cpuidle_enter_state+0x14/0x68) from [<c03ec1c4>] (cpuidle_idle_call+0x94/0x100)
[ 3.957213] [<c03ec1c4>] (cpuidle_idle_call+0x94/0x100) from [<c000f638>] (cpu_idle+0x90/0xec)
[ 3.965834] [<c000f638>] (cpu_idle+0x90/0xec) from [<404e47a8>] (0x404e47a8)
[ 3.972864] CPU2: stopping
[ 3.975522] [<c0014f60>] (unwind_backtrace+0x0/0xf8) from [<c00135b0>] (handle_IPI+0x118/0x140)
[ 3.984252] [<c00135b0>] (handle_IPI+0x118/0x140) from [<c000855c>] (gic_handle_irq+0x60/0x68)
[ 3.992857] [<c000855c>] (gic_handle_irq+0x60/0x68) from [<c000df40>] (__irq_svc+0x40/0x70)
[ 4.001187] Exception stack(0xe706ff40 to 0xe706ff88)
[ 4.006211] ff40: e706ff88 3b9aca00 e6cc8f4d 00000000 e6abaecc 00000000 c17ae3f0 00000000
[ 4.014403] ff60: c070b440 413fc090 c04f33ac 00000000 00000018 e706ff88 c00566a0 c03ec3d4
[ 4.022562] ff80: 60000153 ffffffff
[ 4.026006] [<c000df40>] (__irq_svc+0x40/0x70) from [<c03ec3d4>] (cpuidle_wrap_enter+0x48/0x94)
[ 4.034750] [<c03ec3d4>] (cpuidle_wrap_enter+0x48/0x94) from [<c03ec0dc>] (cpuidle_enter_state+0x14/0x68)
[ 4.044302] [<c03ec0dc>] (cpuidle_enter_state+0x14/0x68) from [<c03ec1c4>] (cpuidle_idle_call+0x94/0x100)
[ 4.053839] [<c03ec1c4>] (cpuidle_idle_call+0x94/0x100) from [<c000f638>] (cpu_idle+0x90/0xec)
[ 4.062435] [<c000f638>] (cpu_idle+0x90/0xec) from [<404e47a8>] (0x404e47a8)
[ 4.069476] CPU3: stopping
[ 4.072136] [<c0014f60>] (unwind_backtrace+0x0/0xf8) from [<c00135b0>] (handle_IPI+0x118/0x140)
[ 4.080860] [<c00135b0>] (handle_IPI+0x118/0x140) from [<c000855c>] (gic_handle_irq+0x60/0x68)
[ 4.089444] [<c000855c>] (gic_handle_irq+0x60/0x68) from [<c000df40>] (__irq_svc+0x40/0x70)
[ 4.097782] Exception stack(0xe7071f40 to 0xe7071f88)
[ 4.102810] 1f40: e7071f88 3b9aca00 e6cc8ea6 00000000 e6abb167 00000000 c17b63f0 00000000
[ 4.111020] 1f60: c070b440 413fc090 c04f33ac 00000000 00000018 e7071f88 c00566a0 c03ec3d4
[ 4.119200] 1f80: 60000153 ffffffff
[ 4.122658] [<c000df40>] (__irq_svc+0x40/0x70) from [<c03ec3d4>] (cpuidle_wrap_enter+0x48/0x94)
[ 4.131423] [<c03ec3d4>] (cpuidle_wrap_enter+0x48/0x94) from [<c03ec0dc>] (cpuidle_enter_state+0x14/0x68)
[ 4.141022] [<c03ec0dc>] (cpuidle_enter_state+0x14/0x68) from [<c03ec1c4>] (cpuidle_idle_call+0x94/0x100)
[ 4.150563] [<c03ec1c4>] (cpuidle_idle_call+0x94/0x100) from [<c000f638>] (cpu_idle+0x90/0xec)
[ 4.159132] [<c000f638>] (cpu_idle+0x90/0xec) from [<404e47a8>] (0x404e47a8)
[ 4.166142] drm_kms_helper: panic occurred, switching back to text console
')