[SOLVED] BB xM Rev C no Ethernet no USB

[Andi]

Hello, I prepared my 8GB SD-Card as described in http://archlinuxarm.org/platforms/armv7/beagleboard-xm
The problem is that Ethernet and USB is not working. The LEDs of the Ethernet port stay dark!
Please help me!

$this->bbcode_second_pass_code('', '
Texas Instruments X-Loader 1.5.1 (Jul 20 2011 - 09:50:57)
Beagle xM
Reading boot sector
Loading u-boot.bin from mmc


U-Boot 2011.06-dirty (Jul 19 2011 - 17:30:34)

OMAP36XX/37XX-GP ES2.1, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 512 MiB
NAND: 0 MiB
MMC: OMAP SD/MMC: 0
*** Warning - readenv() failed, using default environment

In: serial
Out: serial
Err: serial
Beagle xM Rev C
No EEPROM on expansion board
Die ID #271e00029ff80000016849aa13019021
Net: Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot: 0
SD/MMC found on device 0
reading uEnv.txt

143 bytes read
Importing environment from mmc ...
reading boot.scr

228 bytes read
Running boot.scr script from mmc ...
## Executing script at 82000000
mmc - MMC sub system

Usage:
mmc read addr blk# cnt
mmc write addr blk# cnt
mmc rescan
mmc part - lists available partition on current mmc device
mmc dev [dev] [part] - show or set current mmc device [partition]
mmc list - lists available devices
reading uImage

4434624 bytes read
## Booting kernel from Legacy Image at 80300000 ...
Image Name: Linux-3.2.7-1-ARCH
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4434560 Bytes = 4.2 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.141357] Unable to get DVI reset GPIO
[ 0.222106] Could not look up mcpdm hw_mod
[ 0.246459] _omap_mux_init_gpio: Could not set gpio192
[ 2.788391] twl4030_wdt twl4030_wdt: Failed to register misc device
INIT: version 2.88 booting

> Arch Linux ARM

> http://www.archlinuxarm.org

------------------------------
:: Mounting Root Read-Only [DONE]
:: Setting Consoles to UTF-8 mode [DONE]
:: Loading Keyboard Map: us [DONE]
:: Adjusting system time and setting kernel timezone [DONE]
:: Starting UDev Daemon [DONE]
:: Triggering UDev uevents [DONE]
:: Waiting for UDev uevents to be processed [DONE]
:: Bringing up loopback interface [DONE]
:: Unlocking encrypted volumes: [DONE]
:: Checking Filesystems [DONE]
:: Remounting Root [DONE]
:: Mounting Local Filesystems [DONE]
:: Activating Swap [DONE]
:: Configuring Time Zone [DONE]
:: Removing Leftover Files [DONE]
:: Setting Hostname: alarm [DONE]
:: Saving dmesg Log [DONE]
INIT: Entering runlevel: 3
:: Starting Syslog-NG [DONE]
:: Starting Network [BUSY]
Error: unknown interface in /etc/rc.conf: `eth0'
[DONE]
:: Mounting Network Filesystems [DONE]
:: Starting crond daemon [DONE]
:: Starting Secure Shell Daemon [DONE]

Arch Linux 3.2.7-1-ARCH (ttyO2)

alarm login:
')

[Andi]

Hello, i purchased a new BB xM Rev C and everything is working perfektly with the Angstrom image.
I tried the original Angstrom SD-Card on my board where Ethernet and USB is not working without success!
After that i build a SD-Card with the newest release of arch linux ARM and tried it on the new board ==> so far no problems

Therefore I think that there is a hardware fault on the board, hopefully just on this board!!! I will send it in for RMA.

Regards
Andi