Thanks for reading my post asking for help. I am newbie there so much I don't understand in embedded linux.
I am having problem to get my custom build uImage to run. Please point out what stepsI missout/did wrong.
1. using http://releases.linaro.org/12.04/ubuntu/leb-panda/, I then sudo linaro-media-create --mmc /dev/sdX --dev panda --hwpack hwpack_linaro-lt-panda-x11-base_20120505-32_armhf_supported.tar.gz --binary linaro-precise-ubuntu-desktop-20120426-119.tar.gz, with this I created a bootable image on my 8GB SDcard.
2. get the linaro kernel source.
3.
make ARCH=arm CROSS_COMPILE=$COMPILER_DIR omap4_defconfig
make ARCH=arm CROSS_COMPILE=$COMPILER_DIR uImage
make ARCH=arm CROSS_COMPILE=$COMPILER_DIR modules
#sudo make ARCH=arm INSTALL_MOD_PATH=/media/rootfs/ modules_install <--(I am not sure about this steps so I didn't perform)
cp .config /media/boot/config-3.3.1-38-linaro-lt-omap
cp $DEV_KERNEL_LOCATION/arch/arm/boot/uImage /media/boot/
4. boot -> fail. something got to do with ldisc errors.
5. restore the original uImage files, it is able to boot properly. config-3.3.1-38-linaro-lt-omap still retain with the custom build's.
6. Here is the errors:
- d
U-Boot SPL 2012.04.01 (Apr 25 2012 - 15:17:57)
OMAP4460 ES1.1
OMAP SD/MMC: 0
reading u-boot.img
reading u-boot.img
U-Boot 2012.04.01 (Apr 25 2012 - 15:17:57)
CPU : OMAP4460 ES1.1
Board: OMAP4 Panda
I2C: ready
DRAM: 1 GiB
MMC: OMAP SD/MMC: 0
Using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
checking for preEnv.txt
reading preEnv.txt
** Unable to read "preEnv.txt" from mmc 0:1 **
Hit any key to stop autoboot: 0
reading uEnv.txt
** Unable to read "uEnv.txt" from mmc 0:1 **
reading boot.scr
425 bytes read
Loaded script from boot.scr
Running bootscript from mmc0 ...
## Executing script at 82000000
reading uImage
3557024 bytes read
reading uInitrd
3887102 bytes read
## Booting kernel from Legacy Image at 80200000 ...
Image Name: Linux-3.4.0-rc3
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3556960 Bytes = 3.4 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
Image Name: initramfs
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 3887038 Bytes = 3.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
<6>Booting Linux on physical CPU 0
<5>Linux version 3.4.0-rc3 (root@weichons-laptop) (gcc version 4.6.2 20110921 (release) [ARM/embedded-4_6-branch revision 182083] (GNU Tools for ARM Embedded Processors) ) #4 SMP PREEMPT Wed Aug 15 11:24:21 MYT 2012
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: OMAP4 Panda board
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.4.0-rc3 (root@weichons-laptop) (gcc version 4.6.2 20110921 (release) [ARM/embedded-4_6-branch revision 182083] (GNU Tools for ARM Embedded Processors) ) #4 SMP PREEMPT Wed Aug 15 11:24:21 MYT 2012
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: OMAP4 Panda board
<6>bootconsole [earlycon0] enabled
[ 0.000000] bootconsole [earlycon0] enabled
<6>Reserving 50331648 bytes SDRAM for VRAM
[ 0.000000] Reserving 50331648 bytes SDRAM for VRAM
<6>cma: CMA: reserved 16 MiB at ab000000
[ 0.000000] cma: CMA: reserved 16 MiB at ab000000
Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
<6>OMAP4: Map 0xac600000 to 0xfe600000 for dram barrier
[ 0.000000] OMAP4: Map 0xac600000 to 0xfe600000 for dram barrier
<7>On node 0 totalpages: 249344
<7>free_area_init_node: node 0, pgdat c0735d00, node_mem_map c0789000
<7> Normal zone: 1520 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 180240 pages, LIFO batch:31
<7> HighMem zone: 528 pages used for memmap
<7> HighMem zone: 67056 pages, LIFO batch:15
<6>OMAP4460 ES1.0
[ 0.000000] OMAP4460 ES1.0
<6>PERCPU: Embedded 8 pages/cpu @c0f92000 s11840 r8192 d12736 u32768
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c0f92000 s11840 r8192 d12736 u32768
<7>pcpu-alloc: s11840 r8192 d12736 u32768 alloc=8*4096
<7>pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 247296
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 247296
<5>Kernel command line: console=tty0 console=ttyO2,115200n8 root=UUID=a07cfc7f-7167-4e53-b55c-d7ca5854db8f rootwait ro earlyprintk fixrtc nocompcache vram=48M omapfb.vram=0:24M
[ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8 root=UUID=a07cfc7f-7167-4e53-b55c-d7ca5854db8f rootwait ro earlyprintk fixrtc nocompcache vram=48M omapfb.vram=0:24M
<6>PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
<6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Memory:[ 0.000000] Memory: 710MB 710MB 264MB 264MB = 974MB total
= 974MB total
<5>Memory: 960360k/960360k available, 88216k reserved, 270336K highmem
[ 0.000000] Memory: 960360k/960360k available, 88216k reserved, 270336K highmem
<5>Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc065523c (6453 kB)
.init : 0xc0656000 - 0xc06a4e40 ( 316 kB)
.data : 0xc06a6000 - 0xc0738620 ( 586 kB)
.bss : 0xc0738644 - 0xc0788ee0 ( 323 kB)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc065523c (6453 kB)
[ 0.000000] .init : 0xc0656000 - 0xc06a4e40 ( 316 kB)
[ 0.000000] .data : 0xc06a6000 - 0xc0738620 ( 586 kB)
[ 0.000000] .bss : 0xc0738644 - 0xc0788ee0 ( 323 kB)
<6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
<6>Preemptible hierarchical RCU implementation.
[ 0.000000] Preemptible hierarchical RCU implementation.
<6>NR_IRQS:474
[ 0.000000] NR_IRQS:474
<4>omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
[ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
<6>OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
<6>sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
<6>Console: colour dummy device 80x30
[ 0.000000] Console: colour dummy device 80x30
<6>console [tty0] enabled
[ 0.000000] console [tty0] enabled
<6>Calibrating delay loop... [ 0.017395] Calibrating delay loop... <c>1392.74 BogoMIPS (lpj=5439488)
1392.74 BogoMIPS (lpj=5439488)
<6>pid_max: default: 32768 minimum: 301
[ 0.054931] pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 512
[ 0.063659] Mount-cache hash table entries: 512
<6>CPU: Testing write buffer coherency: [ 0.073211] CPU: Testing write buffer coherency: ok
ok
<6>CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.083648] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
<6>Setting up static identity map for 0x80499350 - 0x804993c0
[ 0.095489] Setting up static identity map for 0x80499350 - 0x804993c0
<6>L310 cache controller enabled
[ 0.105377] L310 cache controller enabled
<6>l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x7e470000, Cache size: 1048576 B
[ 0.117004] l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x7e470000, Cache size: 1048576 B
CPU1: Booted secondary processor
<6>CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
<2>CPU1: Unknown IPI message 0x1
<6>Brought up 2 CPUs
<6 >S M P0:.2 T0o2t5a75l ]o fC PU2 1p:r oBoceostseod rss eaccontidvaaryte pdr o(c27e9s2so.8r3
o[g o M IP0S.)2.7
61] CPU1:<6 t>dherveatmdp f-s1,: icnpiu ti1a,l isozecdk
t 0, mpidr 80000001 e
3 0.277313] CPU1: Unknown I<4P>Io mmaesps_ahgwemo d0:x1 l
l3 iv _ c k0.: 2m7i9s2s96in]g Bcroloucgkhdt omuapi n2 fCoPrU s
div_ck.
[ 0.290039] SMP: Total of 2 processors activated (2792.83 BogoMIPS).
[ 0.295349] devtmpfs: initialized
_ 0.309967] omap_hwmod: l3_div_ck: missing clockdomain for l3_di<v4>_ocmk.ap
wmod: i2c1: softreset failed (waited 10000 usec)
[ 0.332000] omap_hwmod: i2c1: softreset failed (waited 10000 usec)
<4>omap_hwmod: i2c2: softreset failed (waited 10000 usec)
[ 0.350891] omap_hwmod: i2c2: softreset failed (waited 10000 usec)
<4>omap_hwmod: i2c3: softreset failed (waited 10000 usec)
[ 0.375640] omap_hwmod: i2c3: softreset failed (waited 10000 usec)
<4>omap_hwmod: i2c4: softreset failed (waited 10000 usec)
[ 0.400421] omap_hwmod: i2c4: softreset failed (waited 10000 usec)
<4>omap_hwmod: mcpdm: cannot be enabled (3)
[ 0.413787] omap_hwmod: mcpdm: cannot be enabled (3)
<6>dummy:
[ 0.422698] dummy:
<6>NET: Registered protocol family 16
[ 0.429504] NET: Registered protocol family 16
<6>DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.463165] DMA: preallocated 256 KiB pool for atomic coherent allocations
<6>GPMC revision 6.0
[ 0.472564] GPMC revision 6.0
<6>gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[ 0.483612] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
<6>OMAP GPIO hardware version 0.1
[ 0.493255] OMAP GPIO hardware version 0.1
<6>gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[ 0.503021] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
<6>gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[ 0.515075] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
<6>gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[ 0.527191] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
<6>gpiochip_add: registered GPIOs 128 to 159 on device: gpio
[ 0.539520] gpiochip_add: registered GPIOs 128 to 159 on device: gpio
<6>gpiochip_add: registered GPIOs 160 to 191 on device: gpio
[ 0.551910] gpiochip_add: registered GPIOs 160 to 191 on device: gpio
<6>omap_mux_init: Add partition: #1: core, flags: 2
[ 0.565093] omap_mux_init: Add partition: #1: core, flags: 2
<6>omap_mux_init: Add partition: #2: wkup, flags: 2
[ 0.576782] omap_mux_init: Add partition: #2: wkup, flags: 2
<3>_omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts
[ 0.591033] _omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts
<3>_omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts
[ 0.604583] _omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts
<3>omap_hwmod_mux_init: Could not allocate device mux entry
[ 0.617370] omap_hwmod_mux_init: Could not allocate device mux entry
<4> usbhs_omap: alias fck already exists
[ 0.630340] usbhs_omap: alias fck already exists
<6>hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.645019] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
<6>hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.658264] hw-breakpoint: maximum watchpoint size is 4 bytes.
<6>OMAP DMA hardware revision 0.0
[ 0.671203] OMAP DMA hardware revision 0.0
<6>bio: create slab <bio-0> at 0
[ 0.706237] bio: create slab <bio-0> at 0
<6>vwl1271: 1800 mV
[ 0.713562] vwl1271: 1800 mV
<5>SCSI subsystem initialized
[ 0.721038] SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>usbcore: registered new interface driver usbfs
[ 0.733215] usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
[ 0.743652] usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
[ 0.753509] usbcore: registered new device driver usb
<6>omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz
[ 0.774139] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz
<4>Skipping twl internal clock init and using bootloader value (unknown osc rate)
[ 0.788085] Skipping twl internal clock init and using bootloader value (unknown osc rate)
<6>twl 1-0048: PIH (irq 39) chaining IRQs 352..372
[ 0.801849] twl 1-0048: PIH (irq 39) chaining IRQs 352..372
<6>VUSB: 3300 mV normal standby
[ 0.811309] VUSB: 3300 mV normal standby
<6>twl6030_usb twl6030_usb: Initialized TWL6030 USB module
[ 1.023864] twl6030_usb twl6030_usb: Initialized TWL6030 USB module
<6>VMMC: 1200 <--> 3000 mV at 3000 mV normal standby
[ 1.036132] VMMC: 1200 <--> 3000 mV at 3000 mV normal standby
<6>VPP: 1800 <--> 2500 mV at 1900 mV normal standby
[ 1.047607] VPP: 1800 <--> 2500 mV at 1900 mV normal standby
<6>VCXIO: 1800 mV normal standby
[ 1.057403] VCXIO: 1800 mV normal standby
<6>VDAC: 1800 mV normal standby
[ 1.065032] VDAC: 1800 mV normal standby
<6>VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
[ 1.075103] VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby
<6>VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby
[ 1.087738] VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby
<6>CLK32KG:
[ 1.096130] CLK32KG:
<6>VANA: 2100 mV normal standby
[ 1.101928] VANA: 2100 mV normal standby
<6>omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz
[ 1.125671] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz
<6>omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
[ 1.149108] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
<6>omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz
[ 1.172546] omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz
<6>Linux media interface: v0.10
[ 1.181640] Linux media interface: v0.10
<6>Linux video capture interface: v2.00
[ 1.189575] Linux video capture interface: v2.00
<6>omap-iommu omap-iommu.0: ducati registered
[ 1.199737] omap-iommu omap-iommu.0: ducati registered
<6>Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 1.210876] Advanced Linux Sound Architecture Driver Version 1.0.25.
<6>Bluetooth: Core ver 2.16
[ 1.221008] Bluetooth: Core ver 2.16
<6>NET: Registered protocol family 31
[ 1.228424] NET: Registered protocol family 31
<6>Bluetooth: HCI device and connection manager initialized
[ 1.238555] Bluetooth: HCI device and connection manager initialized
<6>Bluetooth: HCI socket layer initialized
[ 1.249114] Bluetooth: HCI socket layer initialized
<6>Bluetooth: L2CAP socket layer initialized
[ 1.258331] Bluetooth: L2CAP socket layer initialized
<6>Bluetooth: SCO socket layer initialized
[ 1.267608] Bluetooth: SCO socket layer initialized
<6>Switching to clocksource 32k_counter
[ 1.276611] Switching to clocksource 32k_counter
<4>usbhs_omap usbhs_omap: ehci_logic_fck failed:-2
[ 1.319152] usbhs_omap usbhs_omap: ehci_logic_fck failed:-2
<6>NET: Registered protocol family 2
[ 1.329376] NET: Registered protocol family 2
<6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1.340454] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.355010] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 1.370574] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
<6>TCP: Hash tables configured (established 131072 bind 65536)
[ 1.384399] TCP: Hash tables configured (established 131072 bind 65536)
<6>TCP: reno registered
[ 1.393554] TCP: reno registered
<6>UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.401947] UDP hash table entries: 512 (order: 2, 16384 bytes)
<6>UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.413635] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
<6>NET: Registered protocol family 1
[ 1.423919] NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
[ 1.433837] RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
[ 1.443786] RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
[ 1.452484] RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.462951] RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>Trying to unpack rootfs image as initramfs...
[ 1.474334] Trying to unpack rootfs image as initramfs...
<6>Freeing initrd memory: 3792K
[ 1.810302] Freeing initrd memory: 3792K
highmem bounce pool size: 64 pages
[ 1.858917] highmem bounce pool size: 64 pages
<5>VFS: Disk quotas dquot_6.5.2
[ 1.877746] VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.887664] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<5>NFS: Registering the id_resolver key type
[ 1.902526] NFS: Registering the id_resolver key type
<6>nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.914398] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
<6>msgmni has been set to 1387
[ 1.924316] msgmni has been set to 1387
<6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.936401] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
<6>io scheduler noop registered
[ 1.947052] io scheduler noop registered
<6>io scheduler deadline registered
[ 1.954498] io scheduler deadline registered
<6>io scheduler cfq registered (default)
[ 1.963012] io scheduler cfq registered (default)
<6>OMAP DSS rev 4.0
[ 1.971160] OMAP DSS rev 4.0
<6>Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.116851] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
<6>omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
[ 2.131439] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0
<6>omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
[ 2.145568] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1
<6>omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
[ 2.159729] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2
<6>console [ttyO2] enabled, bootconsole disabled
[ 2.171722] console [ttyO2] enabled, bootconsole disabled
[ 2.171722] console [ttyO2] enabled, bootconsole disabled
<6>omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
[ 2.189758] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3
<6>brd: module loaded
[ 2.210968] brd: module loaded
<6>loop: module loaded
[ 2.222167] loop: module loaded
<6>(stk) :sysfs entries created
[ 2.228515] (stk) :sysfs entries created
<6>(stk) : debugfs entries created [ 2.235809] (stk) : debugfs entries created <6>usbcore: registered new interface driver asix
[ 2.245452] usbcore: registered new interface driver asix
<6>usbcore: registered new interface driver cdc_ether
[ 2.256469] usbcore: registered new interface driver cdc_ether
<6>usbcore: registered new interface driver smsc95xx
[ 2.267639] usbcore: registered new interface driver smsc95xx
<6>usbcore: registered new interface driver net1080
[ 2.278625] usbcore: registered new interface driver net1080
<6>usbcore: registered new interface driver cdc_subset
[ 2.289764] usbcore: registered new interface driver cdc_subset
<6>usbcore: registered new interface driver zaurus
[ 2.300842] usbcore: registered new interface driver zaurus
<6>usbcore: registered new interface driver cdc_ncm
[ 2.311676] usbcore: registered new interface driver cdc_ncm
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.323272] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<4>ehci-omap.0 supply hsusb0 not found, using dummy regulator
[ 2.335906] ehci-omap.0 supply hsusb0 not found, using dummy regulator
<6>ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 2.347656] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
<6>ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[ 2.360198] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
<6>ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00
[ 2.373596] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00
<6>ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 2.395721] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
<6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.407806] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.421295] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: OMAP-EHCI Host Controller
[ 2.433319] usb usb1: Product: OMAP-EHCI Host Controller
<6>usb usb1: Manufacturer: Linux 3.4.0-rc3 ehci_hcd
[ 2.443664] usb usb1: Manufacturer: Linux 3.4.0-rc3 ehci_hcd
<6>usb usb1: SerialNumber: ehci-omap.0
[ 2.453247] usb usb1: SerialNumber: ehci-omap.0
<6>hub 1-0:1.0: USB hub found
[ 2.461517] hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 3 ports detected
[ 2.468536] hub 1-0:1.0: 3 ports detected
<6>Initializing USB Mass Storage driver...
[ 2.504333] Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
[ 2.514801] usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
[ 2.524810] USB Mass Storage support registered.
<6>mousedev: PS/2 mouse device common for all mice
[ 2.534820] mousedev: PS/2 mouse device common for all mice
<4>twl_rtc twl_rtc: Power up reset detected.
[ 2.545745] twl_rtc twl_rtc: Power up reset detected.
<6>twl_rtc twl_rtc: Enabling TWL-RTC
[ 2.555297] twl_rtc twl_rtc: Enabling TWL-RTC
<6>twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 2.567901] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
<6>i2c /dev entries driver
[ 2.577178] i2c /dev entries driver
<6>lirc_dev: IR Remote Control driver registered, major 250
[ 2.587829] lirc_dev: IR Remote Control driver registered, major 250
<6>IR NEC protocol handler initialized
[ 2.598205] IR NEC protocol handler initialized
<6>IR RC5(x) protocol handler initialized
[ 2.606842] IR RC5(x) protocol handler initialized
<6>IR RC6 protocol handler initialized
[ 2.615478] IR RC6 protocol handler initialized
<6>IR JVC protocol handler initialized
[ 2.623840] IR JVC protocol handler initialized
<6>IR Sony protocol handler initialized
[ 2.632293] IR Sony protocol handler initialized
<6>IR RC5 (streamzap) protocol handler initialized
[ 2.641815] IR RC5 (streamzap) protocol handler initialized
<6>IR SANYO protocol handler initialized
[ 2.651458] IR SANYO protocol handler initialized
<6>IR MCE Keyboard/mouse protocol handler initialized
[ 2.661346] IR MCE Keyboard/mouse protocol handler initialized
<6>IR LIRC bridge handler initialized
[ 2.670989] IR LIRC bridge handler initialized
<6>Driver for 1-wire Dallas network protocol.
[ 2.680541] Driver for 1-wire Dallas network protocol.
<6>omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 2.693359] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
<6>Bluetooth: Bluetooth Driver for TI WiLink - Version 1.0
[ 2.706359] Bluetooth: Bluetooth Driver for TI WiLink - Version 1.0
<7>hdev ec103000
<7>hci0 ec103000
<6>(stc): st_register(4) [ 2.718872] (stc): st_register(4) <7>HCI device registered (hdev ec103000)
<6>(stc): chnl_id list empty :4 [ 2.729339] (stc): chnl_id list empty :4 <4>mpu.0 supply vcc not found, using dummy regulator
[ 2.738342] mpu.0 supply vcc not found, using dummy regulator
<6>(stk) : st_kim_start[ 2.746704] (stk) : st_kim_start<6>cpuidle: using governor ladder
[ 2.753082] cpuidle: using governor ladder
<6>cpuidle: using governor menu
[ 2.760620] cpuidle: using governor menu
<4>omap_hsmmc.0 supply vmmc_aux not found, using dummy regulator
[ 2.772369] omap_hsmmc.0 supply vmmc_aux not found, using dummy regulator
<4>omap_hsmmc.4 supply vmmc_aux not found, using dummy regulator
[ 2.788238] omap_hsmmc.4 supply vmmc_aux not found, using dummy regulator
<6>usb 1-1: new high-speed USB device number 2 using ehci-omap
[ 2.802856] usb 1-1: new high-speed USB device number 2 using ehci-omap
<6>(stk) :ldisc_install = 1[ 2.904632] (stk) :ldisc_install = 1<7>Registered led device: pandaboard::status1
<7>Registered led device: pandaboard::status2
<6>usbcore: registered new interface driver usbhid
[ 2.934783] usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
[ 2.943603] usbhid: USB HID core driver
<6>ALSA device list:
[ 2.950836] ALSA device list:
<6> No soundcards found.
[ 2.956420] No soundcards found.
<6>oprofile: hardware counters not available
[ 2.964141] oprofile: hardware counters not available
<6>oprofile: using timer interrupt.
[ 2.972839] oprofile: using timer interrupt.
<6>TCP: cubic registered
<6>usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[<6>u sb 1 -1: Ne w 2US.B de9vice7 str9ings: 9Mf8r=00, Pro]du ctT=0, SeCriPal:Nu mberc=0
ubic registered
[ 2.985778] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[ 2.993835] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<6>hub 1-1:1.0: USB hub found
[ 3.013305] hub 1-1:1.0: USB hub found
<6>hub 1-1:1.0: 5 ports detected
<6>NET: Registered protocol family 10
[ 3.<6>IP0v6 ove2r 0IP4v4 tunnel7in7g ]driver
hub 1-1:1<6>.NE0T:: R egis5tere d pprootocorl tfasmily 17
amileNETt: Regiestcerted preotocdol f
y 15
3.023956] NET: Registered protocol family 10
[ 3.028625] IPv6 over IPv4 tunneling driver
[ 3.033874] NET: Registered protocol family 17
[ 3.038299] NET: Registered protocol family 15
<6>Bluetooth: RFCOMM TTY layer initialized
[ 3.060852] Bluetooth: RFCOMM TTY layer initialized
<6>Bluetooth: RFCOMM socket layer initialized
[ 3.070312] Bluetooth: RFCOMM socket layer initialized
<6>Bluetooth: RFCOMM ver 1.11
[ 3.078552] Bluetooth: RFCOMM ver 1.11
<6>Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.086914] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 3.097595] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>VFP support v0.3: [ 3.106079] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
implementor 41 architecture 3 part 30 variant 9 rev 4
<6>ThumbEE CPU extension supported.
[ 3.122528] ThumbEE CPU extension supported.
<4>omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0).[ 3.135437] omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0).<4>omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0).
[ 3.150787] omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0).<3>Power Management for TI OMAP4.
[ 3.163726] Power Management for TI OMAP4.
<6>registered taskstats version 1
[ 3.176696] registered taskstats version 1
<4>mmc0: host does not support reading read-only switch. assuming write-enable.
[ 3.316650] mmc0: host does not support reading read-only switch. assuming write-enable.
<6>mmc0: new high speed SDHC card at address 1234
[ 3.332183] mmc0: new high speed SDHC card at address 1234
<6>mmcblk0: mmc0:1234 SA08G 7.42 GiB
[ 3.342010] mmcblk0: mmc0:1234 SA08G 7.42 GiB
<6>usb 1-1.1: new high-speed USB device number 3 using ehci-omap
[ 3.352844] usb 1-1.1: new high-speed USB device number 3 using ehci-omap
<6> mmcblk0: p1 p2
[ 3.364898] mmcblk0: p1 p2
<6>Console: switching to colour frame buffer device 80x30
[ 3.421966] Console: switching to colour frame buffer device 80x30
<4>omapdss DPI: Could not find exact pixel clock. Requested 23500 kHz, got 23630 kHz
[ 3.450408] omapdss DPI: Could not find exact pixel clock. Requested 23500 kHz, got 23630 kHz
<4>VANA: incomplete constraints, leaving on
[ 3.471435] VANA: incomplete constraints, leaving on
<4>CLK32KG: incomplete constraints, leaving on
[ 3.483703] CLK32KG: incomplete constraints, leaving on
<4>VDAC: incomplete constraints, leaving on
[ 3.497314] VDAC: incomplete constraints, leaving on
<6>usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 3.511749] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
<6>usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.528015] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
<4>VUSB: incomplete constraints, leaving on
[ 3.545043] VUSB: incomplete constraints, leaving on
<6>smsc95xx v1.0.4
[ 3.559844] smsc95xx v1.0.4
<4>mmc1: card claims to support voltages below the defined range. These will be ignored.
[ 3.573577] mmc1: card claims to support voltages below the defined range. These will be ignored.
<6>twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 3.595245] twl_rtc twl_rtc: setting syste<m4> mmcc1: quleuoincg unkkn owtn oCIS tupl2e 00x901 0(3 b-ytes0)
1-01 00:00:00 UTC<6>m mc1:( n9ew4 S6DIO 6card a8t 4ad8dres0s 000)01
[ 3.605438] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)
[ 3.611694] mmc1: new SDIO card at address 0001
<6>Freeing init memory: 312K
[ 3.635742] Freeing init memory: 312K
Loading, please wait...
<30>udevd[1251]: starting version 175
[ 3.701812] udevd[1251]: starting version 175
<6>smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-ehci-omap.0-1.1, smsc95xx USB 2.0 Ethernet, 46:c8:06:cb:1f:92
[ 3.726257] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-ehci-omap.0-1.1, smsc95xx USB 2.0 Ethernet, 46:c8:06:cb:1f:92
Begin: Loading essential drivers ... FATAL: Could not load /lib/modules/3.4.0-rc3/modules.dep: No such file or directory
FATAL: Could not load /lib/modules/3.4.0-rc3/modules.dep: No such file or directory
FATAL: Could not load /lib/modules/3.4.0-rc3/modules.dep: No such file or directory
FATAL: Could not load /lib/modules/3.4.0-rc3/modules.dep: No such file or directory
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
<3>(stk) :ldisc installation timeout[ 3.909820] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
[ 3.925781] (stk) :ldisc_install = 0<6>usb 1-1.2: new full-speed USB device number 4 using ehci-omap
[ 4.068878] usb 1-1.2: new full-speed USB device number 4 using ehci-omap
Begin: Running /scripts/local-premount ... FATAL: Could not load /lib/modules/3.4.0-rc3/modules.dep: No such file or directory
<6>usb 1-1.2: New USB device found, idVendor=192f, idProduct=0000
[ 4.205505] usb 1-1.2: New USB device found, idVendor=192f, idProduct=0000
<6>usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.252990] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
<6>usb 1-1.2: Product: C8051F326 Development Board
[ 4.278869] usb 1-1.2: Product: C8051F326 Development Board
<6>usb 1-1.2: Manufacturer: SILICON LABORATORIES
[ 4.295471] usb 1-1.2: Manufacturer: SILICON LABORATORIES
<6>input: SILICON LABORATORIES C8051F326 Development Board as /devices/platform/usbhs_omap/ehci-omap.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input0
[ 4.322021] input: SILICON LABORATORIES C8051F326 Development Board as /devices/platform/usbhs_omap/ehci-omap.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input0
<6>generic-usb 0003:192F:0000.0001: input,hiddev0,hidraw0: USB HID v1.01 Mouse [SILICON LABORATORIES C8051F326 Development Board] on usb-ehci-omap.0-1.2/input0
[ 4.357543] generic-usb 0003:192F:0000.0001: input,hiddev0,hidraw0: USB HID v1.01 Mouse [SILICON LABORATORIES C8051F326 Development Board] on usb-ehci-omap.0-1.2/input0
<6>usb 1-1.3: new low-speed USB device number 5 using ehci-omap
[ 4.482849] usb 1-1.3: new low-speed USB device number 5 using ehci-omap
done.
FATAL: Could not load /lib/modules/3.4.0-rc3/modules.dep: No such file or directory
<6>EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.618804] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
Begin: Running /scripts/local-bottom ... done.
done.
<6>usb 1-1.3: New USB device found, idVendor=03f0, idProduct=0024
[ 4.644989] usb 1-1.3: New USB device found, idVendor=03f0, idProduct=0024
Begin: Running /<6>usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.662963] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
scripts/init-bottom ... <6>usb 1-1.3: Product: HP Basic USB Keyboard
[ 4.683990] usb 1-1.3: Product: HP Basic USB Keyboard
<6>usb 1-1.3: Manufacturer: CHICONY
[ 4.695373] usb 1-1.3: Manufacturer: CHICONY
<6>input: CHICONY HP Basic USB Keyboard as /devices/platform/usbhs_omap/ehci-omap.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input1
[ 4.719635] input: CHICONY HP Basic USB Keyboard as /devices/platform/usbhs_omap/ehci-omap.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input1
<6>generic-usb 0003:03F0:0024.0002: input,hidraw1: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-ehci-omap.0-1.3/input0
[ 4.750122] generic-usb 0003:03F0:0024.0002: input,hidraw1: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-ehci-omap.0-1.3/input0
done.
<3>(stk) : timed out waiting for ldisc to be un-installed[ 4.935058] (stk) : timed out waiting for ldisc to be un-installed<6>(stk) :ldisc_install = 1
[ 5.142517] (stk) :ldisc_install = 1<3>(stk) :ldisc installation timeout
[ 6.151947] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
[ 6.162170] (stk) :ldisc_install = 0<30>udevd[1480]: starting version 175
<3>(stk) : timed out waiting for ldisc to be un-installed[ 7.169464] (stk) : timed out waiting for ldisc to be un-installed<6>(stk) :ldisc_install = 1
<6>EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
<3>(stk) :ldisc installation timeout[ 8.331604] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed[ 9.341339] (stk) : timed out waiting for ldisc to be un-installed<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout[ 10.503509] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed[ 11.513214] (stk) : timed out waiting for ldisc to be un-installedfsck from util-linux 2.20.1
rootfs: Superblock last write time is in the future.
(by less than a day, probably due to the hardware clock being incorrectly set). FIXED.
rootfs: clean, 179470/483328 files, 540595/1932288 blocks
<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout[ 13.151977] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed[ 14.161651] (stk) : timed out waiting for ldisc to be un-installed<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout[ 15.323822] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed[ 16.333526] (stk) : timed out waiting for ldisc to be un-installed<3>Bluetooth: st_register failed -22
[ 16.343719] Bluetooth: st_register failed -22
<7>hci0 ec103000
<6>(stc): st_register(4) <6>(stc): chnl_id list empty :4 <6>(stk) : st_kim_start<6>(stk) :ldisc_install = 1<3>(stk) :ldisc installation timeout[ 17.519104] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed[ 18.528808] (stk) : timed out waiting for ldisc to be un-installed<6>(stk) :ldisc_install = 1
* Starting mDNS/DNS-SD daemon [ OK ]
<3>(stk) :ldisc installation timeout[ 19.691009] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed[ 20.708526] (stk) : timed out waiting for ldisc to be un-installed<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout[ 21.870727] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed[ 22.880401] (stk) : timed out waiting for ldisc to be un-installed<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout[ 24.042602] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed[ 25.052246] (stk) : timed out waiting for ldisc to be un-installed<6>(stk) :ldisc_install = 1
* Starting configure network device security [ OK ]
* Starting configure network device security [ OK ]
* Starting configure network device [ OK ]
* Starting configure network device security [ OK ]
* Starting CUPS printing spooler/server [ OK ]
* Starting configure network device [ OK ]
<3>(stk) :ldisc installation timeout[ 26.214477] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed[ 27.224151] (stk) : timed out waiting for ldisc to be un-installed<6>(stk) :ldisc_install = 1
<3>(stk) :ldisc installation timeout[ 28.386352] (stk) :ldisc installation timeout<6>(stk) :ldisc_install = 0
<3>(stk) : timed out waiting for ldisc to be un-installed[ 29.396026] (stk) : timed out waiting for ldisc to be un-installed<3>Bluetooth: st_register failed -22
[ 29.406219] Bluetooth: st_register failed -22
* Stopping configure virtual network devices [ OK ]
* Stopping save udev log and update rules [ OK ]
* Starting Mount network filesystems [ OK ]
* Starting Failsafe Boot Delay [ OK ]
* Stopping Mount network filesystems [ OK ]
* Starting Bridge socket events into upstart [ OK ]
<7>eth0: no IPv6 routers present
* Starting network connection manager [ OK ]
* Stopping Read required files in advance [ OK
[/list]