USB host issues

[eslarsen]

I'm trying to keep a usb hard drive connected to the BeagleBone Black, but the usb host is not working to well. Most of the time, the device does not even show up on lsusb. It doesn't work on boot either, but seem to have a 10% chance of working when I plug it in.

Looking around, this seems like a relatively known problem, which is very disappointing.

Is anyone else here seeing this?

[Noy]

Hello Guys,
I have a similar problem. If I boot my BBB with external active USB Hub and plugged into it my UMTS USB Stick it is recognised.
But if it is then plugged out and after some time in again it isn't. Also my HUB is gone after some time of suspend.

I mean its not listed in lsusb and also the /dev/usbtty3 is gone.

Where is the problem?

dmesg says:
$this->bbcode_second_pass_code('', '
[ 2.675078] scsi 0:0:0:0: CD-ROM USBModem Disk 2.31 PQ: 0 ANSI: 2
[ 2.682697] sr0: scsi-1 drive
[ 2.682720] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.683549] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 2.684370] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 3.182209] systemd-udevd[128]: starting version 212
[ 3.350926] systemd-journald[116]: Received request to flush runtime journal from PID 1
[ 7.166620] net eth0: initializing cpsw version 1.12 (0)
[ 7.169982] net eth0: phy found : id is : 0x7c0f1
[ 7.170006] libphy: PHY 4a101000.mdio:01 not found
[ 7.175088] net eth0: phy 4a101000.mdio:01 not found on slave 1
[ 7.197535] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.248220] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
[ 10.248293] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.273442] usb-storage 1-1.1:1.0: disconnect by usbfs
[ 13.799584] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0002
[ 13.800091] hub 1-1:1.0: port 1, status 0101, change 0001, 12 Mb/s
[ 13.802435] usb 1-1.1: USB disconnect, device number 3
[ 13.802455] usb 1-1.1: unregistering device
[ 13.802469] usb 1-1.1: unregistering interface 1-1.1:1.0
[ 13.802832] usb 1-1.1: usb_disable_device nuking all URBs
[ 13.911915] hub 1-1:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
[ 13.978313] usb 1-1.1: new high-speed USB device number 4 using musb-hdrc
[ 14.068330] usb 1-1.1: default language 0x0409
[ 14.071941] usb 1-1.1: udev 4, busnum 1, minor = 3
[ 14.071962] usb 1-1.1: New USB device found, idVendor=1c9e, idProduct=9605
[ 14.071974] usb 1-1.1: New USB device strings: Mfr=3, Product=2, SerialNumber=4
[ 14.071985] usb 1-1.1: Product: USB Modem
[ 14.071995] usb 1-1.1: Manufacturer: USB Modem
[ 14.072004] usb 1-1.1: SerialNumber: 1234567890ABCDEF
[ 14.072513] usb 1-1.1: usb_probe_device
[ 14.072532] usb 1-1.1: configuration #1 chosen from 1 choice
[ 14.856420] usb 1-1.1: adding 1-1.1:1.0 (config #1, interface 0)
[ 14.856872] usb 1-1.1: adding 1-1.1:1.1 (config #1, interface 1)
[ 14.857247] usb 1-1.1: adding 1-1.1:1.2 (config #1, interface 2)
[ 14.857546] usb 1-1.1: adding 1-1.1:1.3 (config #1, interface 3)
[ 14.857913] usb 1-1.1: adding 1-1.1:1.4 (config #1, interface 4)
[ 14.858985] usb-storage 1-1.1:1.4: usb_probe_interface
[ 14.859019] usb-storage 1-1.1:1.4: usb_probe_interface - got id
[ 14.861803] scsi1 : usb-storage 1-1.1:1.4
[ 15.866402] scsi 1:0:0:0: Direct-Access USBModem Disk 2.31 PQ: 0 ANSI: 2
[ 15.873081] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 15.873288] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 16.002164] usbcore: registered new interface driver usbserial
[ 16.003545] usbcore: registered new interface driver usbserial_generic
[ 16.006290] usbserial: USB Serial support registered for generic
[ 16.023753] usbcore: registered new interface driver option
[ 16.025778] usbserial: USB Serial support registered for GSM modem (1-port)
[ 16.030438] option 1-1.1:1.0: usb_probe_interface
[ 16.030490] option 1-1.1:1.0: usb_probe_interface - got id
[ 16.030574] option 1-1.1:1.0: GSM modem (1-port) converter detected
[ 16.035434] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB0
[ 16.035894] option 1-1.1:1.1: usb_probe_interface
[ 16.035943] option 1-1.1:1.1: usb_probe_interface - got id
[ 16.036021] option 1-1.1:1.1: GSM modem (1-port) converter detected
[ 16.043002] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB1
[ 16.046758] option 1-1.1:1.2: usb_probe_interface
[ 16.046811] option 1-1.1:1.2: usb_probe_interface - got id
[ 16.046894] option 1-1.1:1.2: GSM modem (1-port) converter detected
[ 16.054518] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB2
[ 16.054761] option 1-1.1:1.3: usb_probe_interface
[ 16.054808] option 1-1.1:1.3: usb_probe_interface - got id
[ 16.054889] option 1-1.1:1.3: GSM modem (1-port) converter detected
[ 16.063781] usb 1-1.1: GSM modem (1-port) converter now attached to ttyUSB3
[ 16.842470] PPP generic driver version 2.4.2
[ 23.288171] PPP BSD Compression module registered
[ 23.301410] PPP Deflate Compression module registered
[ 542.541563] option1 ttyUSB3: option_instat_callback: error -71
[ 542.548135] option1 ttyUSB3: option_instat_callback: error -71
[ 542.554642] option1 ttyUSB3: option_instat_callback: error -71
[ 542.561145] option1 ttyUSB3: option_instat_callback: error -71
[ 542.567634] option1 ttyUSB3: option_instat_callback: error -71
[ 542.574141] option1 ttyUSB3: option_instat_callback: error -71
[ 542.580640] option1 ttyUSB3: option_instat_callback: error -71
[ 542.587139] option1 ttyUSB3: option_instat_callback: error -71
[ 542.593638] option1 ttyUSB3: option_instat_callback: error -71
[ 542.600135] option1 ttyUSB3: option_instat_callback: error -71
[ 542.606636] option1 ttyUSB3: option_instat_callback: error -71
[ 542.613142] option1 ttyUSB3: option_instat_callback: error -71
[ 542.619639] option1 ttyUSB3: option_instat_callback: error -71
[ 542.626136] option1 ttyUSB3: option_instat_callback: error -71
[ 542.632637] option1 ttyUSB3: option_instat_callback: error -71
[ 542.639148] option1 ttyUSB3: option_instat_callback: error -71
[ 542.645633] option1 ttyUSB3: option_instat_callback: error -71
[ 542.652135] option1 ttyUSB3: option_instat_callback: error -71
[ 542.658633] option1 ttyUSB3: option_instat_callback: error -71
[ 542.665133] option1 ttyUSB3: option_instat_callback: error -71
[ 542.671635] option1 ttyUSB3: option_instat_callback: error -71
[ 542.678135] option1 ttyUSB3: option_instat_callback: error -71
[ 542.684635] option1 ttyUSB3: option_instat_callback: error -71
[ 542.691131] option1 ttyUSB3: option_instat_callback: error -71
[ 542.697472] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0002
[ 542.697629] option1 ttyUSB3: option_instat_callback: error -71
[ 542.704136] option1 ttyUSB3: option_instat_callback: error -71
[ 542.710631] option1 ttyUSB3: option_instat_callback: error -71
[ 542.716973] hub 1-1:1.0: port 1, status 0100, change 0001, 12 Mb/s
[ 542.717131] option1 ttyUSB3: option_instat_callback: error -71
[ 542.723469] usb 1-1.1: USB disconnect, device number 4
[ 542.723512] usb 1-1.1: unregistering device
[ 542.723551] usb 1-1.1: unregistering interface 1-1.1:1.0
[ 542.723624] option1 ttyUSB3: option_instat_callback: error -71
[ 542.742074] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 542.742387] option 1-1.1:1.0: device disconnected
[ 542.742617] usb 1-1.1: unregistering interface 1-1.1:1.1
[ 542.748174] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 542.748396] option 1-1.1:1.1: device disconnected
[ 542.748613] usb 1-1.1: unregistering interface 1-1.1:1.2
[ 542.755990] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 542.756220] option 1-1.1:1.2: device disconnected
[ 542.756442] usb 1-1.1: unregistering interface 1-1.1:1.3
[ 542.761807] option1 ttyUSB3: GSM modem (1-port) converter now disconnected from ttyUSB3
[ 542.762043] option 1-1.1:1.3: device disconnected
[ 542.762261] usb 1-1.1: unregistering interface 1-1.1:1.4
[ 542.783651] usb 1-1.1: usb_disable_device nuking all URBs
[ 542.898638] hub 1-1:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
[ 542.900181] hub 1-1:1.0: hub_suspend
[ 542.904003] usb 1-1: usb auto-suspend, wakeup 1
[ 542.917822] hub 1-0:1.0: hub_suspend
[ 542.917922] usb usb1: bus auto-suspend, wakeup 1
[ 6299.724875] usb usb1: usb wakeup-resume
[ 6299.724929] usb usb1: usb auto-resume
[ 6299.724951] hub 1-0:1.0: hub_resume
[ 6299.724997] hub 1-0:1.0: port 1: status 0507 change 0004
[ 6299.725017] CAUTION: musb: Babble Interrupt Occurred
[ 6299.725082] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
[ 6299.747630] usb 1-1: usb wakeup-resume
[ 6299.747710] usb 1-1: finish resume
[ 6304.747771] usb 1-1: khubd timed out on ep0in len=0/2
[ 6304.747830] usb 1-1: retry with reset-resume
[ 6304.853337] usb 1-1: reset high-speed USB device number 2 using musb-hdrc
[ 6309.853256] usb 1-1: khubd timed out on ep0in len=0/64
[ 6314.853248] usb 1-1: khubd timed out on ep0in len=0/64
[ 6319.853291] usb 1-1: khubd timed out on ep0in len=0/64
[ 6319.958697] usb 1-1: device descriptor read/64, error -110
[ 6325.067994] usb 1-1: khubd timed out on ep0in len=0/64
[ 6330.068096] usb 1-1: khubd timed out on ep0in len=0/64
[ 6335.068094] usb 1-1: khubd timed out on ep0in len=0/64
[ 6335.173523] usb 1-1: device descriptor read/64, error -110
[ 6335.388366] usb 1-1: reset high-speed USB device number 2 using musb-hdrc
[ 6340.388443] usb 1-1: khubd timed out on ep0in len=0/64
[ 6345.388419] usb 1-1: khubd timed out on ep0in len=0/64
[ 6350.388389] usb 1-1: khubd timed out on ep0in len=0/64
[ 6350.493864] usb 1-1: device descriptor read/64, error -110
[ 6355.603240] usb 1-1: khubd timed out on ep0in len=0/64
[ 6360.603262] usb 1-1: khubd timed out on ep0in len=0/64
[ 6365.604265] usb 1-1: khubd timed out on ep0in len=0/64
[ 6365.708727] usb 1-1: device descriptor read/64, error -110
[ 6365.923570] usb 1-1: reset high-speed USB device number 2 using musb-hdrc
[ 6370.923565] usb 1-1: khubd timed out on ep0out len=0/0
[ 6376.126692] usb 1-1: khubd timed out on ep0out len=0/0
[ 6376.329859] usb 1-1: device not accepting address 2, error -110
[ 6376.454802] usb 1-1: reset high-speed USB device number 2 using musb-hdrc
[ 6381.454826] usb 1-1: khubd timed out on ep0out len=0/0
[ 6386.657931] usb 1-1: khubd timed out on ep0out len=0/0
[ 6386.861032] usb 1-1: device not accepting address 2, error -110
[ 6386.870945] hub 1-0:1.0: logical disconnect on port 1
[ 6386.871031] usb 1-1: gone after usb resume? status -19
[ 6386.871068] usb 1-1: can't resume, status -19
[ 6386.871100] hub 1-0:1.0: logical disconnect on port 1
[ 6386.871175] hub 1-0:1.0: resume on port 1, status -19
[ 6386.871221] hub 1-0:1.0: port 1, status 0507, change 0004, 480 Mb/s
[ 6386.871260] usb 1-1: USB disconnect, device number 2
[ 6386.871295] usb 1-1: unregistering device
[ 6386.871330] usb 1-1: unregistering interface 1-1:1.0
[ 6386.878775] usb 1-1: usb_disable_device nuking all URBs
[ 6386.986036] usb 1-1: new high-speed USB device number 5 using musb-hdrc
[ 6391.986102] usb 1-1: khubd timed out on ep0in len=0/64
[ 6396.986074] usb 1-1: khubd timed out on ep0in len=0/64
[ 6401.986091] usb 1-1: khubd timed out on ep0in len=0/64
[ 6402.091497] usb 1-1: device descriptor read/64, error -110
[ 6407.200896] usb 1-1: khubd timed out on ep0in len=0/64
[ 6412.200907] usb 1-1: khubd timed out on ep0in len=0/64
[ 6417.200913] usb 1-1: khubd timed out on ep0in len=0/64
[ 6417.306363] usb 1-1: device descriptor read/64, error -110
[ 6417.521158] usb 1-1: new high-speed USB device number 6 using musb-hdrc
[ 6422.521245] usb 1-1: khubd timed out on ep0in len=0/64
[ 6427.521223] usb 1-1: khubd timed out on ep0in len=0/64
[ 6432.521274] usb 1-1: khubd timed out on ep0in len=0/64
[ 6432.626657] usb 1-1: device descriptor read/64, error -110
[ 6437.736092] usb 1-1: khubd timed out on ep0in len=0/64
[ 6442.736056] usb 1-1: khubd timed out on ep0in len=0/64
[ 6447.736099] usb 1-1: khubd timed out on ep0in len=0/64
[ 6447.841478] usb 1-1: device descriptor read/64, error -110
[ 6448.056409] usb 1-1: new high-speed USB device number 7 using musb-hdrc
[ 6453.056427] usb 1-1: khubd timed out on ep0out len=0/0
[ 6458.259540] usb 1-1: khubd timed out on ep0out len=0/0
[ 6458.462570] usb 1-1: device not accepting address 7, error -110
[ 6458.575950] usb 1-1: new high-speed USB device number 8 using musb-hdrc
[ 6463.575894] usb 1-1: khubd timed out on ep0out len=0/0
[ 6468.779039] usb 1-1: khubd timed out on ep0out len=0/0
[ 6468.982097] usb 1-1: device not accepting address 8, error -110
[ 6468.990416] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 6469.000735] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[ 6469.000828] hub 1-0:1.0: port 1 enable change, status 00000501
[ 6469.000997] hub 1-0:1.0: hub_suspend
[ 6469.001070] usb usb1: bus auto-suspend, wakeup 1
')