by ryansturmer » Sun Jul 27, 2014 6:10 pm
Here are the logs, first for the beaglebone that didn't work:
$this->bbcode_second_pass_code('', '
U-Boot SPL 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)
reading args
spl_load_image_fat_os: error reading image args, err - -1
reading u-boot.img
reading u-boot.img
U-Boot 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)
I2C: ready
DRAM: 512 MiB
NAND: 0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
Net: <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 1 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
603 bytes read in 4 ms (146.5 KiB/s)
gpio: pin 55 (gpio 55) value is 1
Loaded environment from uEnv.txt
Importing environment from mmc ...
Checking if uenvcmd is set ...
gpio: pin 56 (gpio 56) value is 1
Running uenvcmd ...
mmc0 is current device
3334320 bytes read in 233 ms (13.6 MiB/s)
25926 bytes read in 79 ms (320.3 KiB/s)
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
--- THIS REPEATS FOR SOME TIME, SEVERAL MINUTES AT LEAST ---
mmc0 is current device
3334320 bytes read in 232 ms (13.7 MiB/s)
25926 bytes read in 80 ms (316.4 KiB/s)
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
** Unable to read file uEnv.txt **
Checking if uenvcmd is set ...
gpio: pin 56 (gpio 56) value is 1
Running uenvcmd ...
ERROR : memory not allocated
---- THE DEVICE APPEARS TO REBOOT HERE ----
U-Boot SPL 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)
reading args
spl_load_image_fat_os: error reading image args, err - -1
reading u-boot.img
reading u-boot.img
U-Boot 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54)
')
Then for the board that works fine. These two were run with the SAME SD CARD.
$this->bbcode_second_pass_code('', '
U-Boot SPL 2013.07 (Aug 09 2013 - 18:03:11)
musb-hdrc: Co
nfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
mmc_send_cmd : timeout: No status update
reading args
spl:
error reading image args, err - -1
reading u-boot.img
reading u-boot.img
U-Boot 2013.07 (Aug 09 2013 - 18:03:11)
I2C: ready
DRAM: 512 MiB
WARNING: Caches not enabled
NAND:
0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning -
readenv() failed, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-
ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 1
\0x08\0x08\0x08 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current de
vice
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
reading uEnv.txt
603 bytes read in 3 ms (196.3 KiB/s)
Importing environment from mmc ...
gpio: pin 55 (gpio 55) value is 1
Checking if uenvcmd is set ...
gpio: pin 56 (gpio 56) value is 1
Running uenvcmd ...
mmc0 is current device
3334320 bytes read in 582 ms (5.5 MiB/s)
25926 bytes read i
n 83 ms (304.7 KiB/s)
Booting from mmc ...
Kernel image @ 0x80200000 [ 0x000000 - 0x32e0b0 ]
## Flattened Device Tree blob at 80f80000
Booting using the fdt blob at 0x80f80000
Using Device Tree in place at 80f80000, end 80f89545
Starting kernel ...
Uncompressing Linux...
done, booting the kernel.
')