i am using goflex net and alarm. One of the HDD is out of order, i fixed the rc.conf and fstab...reboot and having this kernel panic
$this->bbcode_second_pass_code('', '$ sudo nc -lus 10.10.10.4 -p 6666
[ 4.934563] rtc-mv rtc-mv: internal RTC not ticking
[ 6.584845] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 6.591785] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 6.600157] [<c000d264>] (unwind_backtrace+0x0/0xe0) from [<c03d2ac4>] (panic+0x58/0x194)
[ 6.608435] [<c03d2ac4>] (panic+0x58/0x194) from [<c0539bc0>] (mount_block_root+0x234/0x284)
[ 6.616958] [<c0539bc0>] (mount_block_root+0x234/0x284) from [<c0539ecc>] (prepare_namespace+0x160/0x1c0)
[ 6.626608] [<c0539ecc>] (prepare_namespace+0x160/0x1c0) from [<c053985c>] (kernel_init+0xe8/0x114)
[ 6.635735] [<c053985c>] (kernel_init+0xe8/0x114) from [<c0009458>] (kernel_thread_exit+0x0/0x8)
')
Uboot log
$this->bbcode_second_pass_code('', '$ sudo nc -lus 10.10.10.5 -p 6666
U-Boot 2010.09 (Feb 16 2011 - 18:42:02)
UBIT v0.6 by Jeff Doozan and Peter Carmichael
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:fast", error -19
Error reading superblock on volume 'ubi:fast'!
UBIFS not mounted, use ubifs mount to mount volume first!
** Block device usb 0 not supported
** Block device usb 0 not supported
** Invalid boot device **
** Invalid boot device **
** Block device usb 1 not supported
** Block device usb 1 not supported
** Invalid boot device **
** Invalid boot device **
** Block device usb 2 not supported
** Block device usb 2 not supported
** Invalid boot device **
** Invalid boot device **
** Block device usb 3 not supported
** Block device usb 3 not supported
** Invalid boot device **
** Invalid boot device **
Reset IDE: Bus 0: not available Bus 1: OK
Device 1: Model: ST1000LM010-9YH146 Firm: CC9F Ser#: W10024B1
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
** Bad partition 1 **
** Bad partition 1 **
No Powersaving mode 7F
Error (no IRQ) dev 0 blk 0: status 0x7f
** Can't read from device 0 **
** Unable to use ide 0:1 for fatload **
No Powersaving mode 7F
Error (no IRQ) dev 0 blk 0: status 0x7f
** Can't read from device 0 **
** Unable to use ide 0:1 for fatload **
Loading file "/boot/uImage" from ide device 1:1 (hdb1)
2860348 bytes read
Loading file "/uInitrd" from ide device 1:1 (hdb1)
** File not found /uInitrd
Loading file "/boot/uInitrd" from ide device 1:1 (hdb1)
** File not found /boot/uInitrd
## Booting kernel from Legacy Image at 00680000 ...
Image Name: Linux-3.1.10-4-ARCH
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2860284 Bytes = 2.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...')
btw i have done chroot and pacman -Syu before, i hope it really does not matter
.chroot is done by
$this->bbcode_second_pass_code('', 'cd /mnt/arch
mount -t proc proc proc/
mount -t sysfs sys sys/
mount -o bind /dev dev/')
So what is the problem? Thanks
I did that once too..