PogoPlug E02 Black problem

[msanad]

hello every one

i have bought my PogoPlug E02 black one one week ago and yesterday i tried to install uboot (/install_uboot_mtd0.sh) and then to install Arch Linux ARM but unfortunallty i go error message (Installation cancelled.) then i forced the installation with (--no-uboot-check ) but again i go this message (uBoot could not be downloaded, or the MD5 does not match.)
the prompet of the switched from bash to pogoplug and i have tried to install again but with no result.

then i found one topic (dont remeber it now ) which contains some steps how to remove some data from flash and the earse !!!! actully i'm not fimilar with these command in unix but i tried it.
now i cant access it via ssh but can access using serial connection , below is the messages i got , it stops at this line

$this->bbcode_second_pass_code('', 'Scheduling watchdog timeout to force reboot...')

then start the boot over again

$this->bbcode_second_pass_code('', 'U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x200000

Reading data from 0x2ff800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2010-10-19 23:05:02 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1979140 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux............................................................................................................................ done, booting the kernel.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total
[ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init)
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] NET: Registered protocol family 16
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e8000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] INTER_REGS ....base f1000000, size 1MB
[ 0.250000] NFLASH_CS ....base fa000000, size 2MB
[ 0.250000] SPI_CS ....base f4000000, size 16MB
[ 0.250000] BOOT_ROM_CS ....no such
[ 0.250000] DEV_BOOTCS ....no such
[ 0.250000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.250000]
[ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.250000]
[ 0.250000] Detected Tclk 200000000 and SysClk 400000000
[ 0.250000] MV Buttons Device Load
[ 0.250000] Marvell USB EHCI Host controller #0: c0652600
[ 0.750000] PEX0 interface detected no Link.
[ 0.750000] PCI: bus0: Fast back to back transfers enabled
[ 0.750000] SCSI subsystem initialized
[ 0.750000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.750000] NET: Registered protocol family 2
[ 0.760000] Time: kw_clocksource clocksource has been installed.
[ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.850000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.850000] TCP reno registered
[ 0.880000] RTC has been updated!!!
[ 0.880000] RTC registered
[ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.880000] o RAID 5 Xor calculation
[ 0.880000] o kernel memcpy
[ 0.880000] o kenrel memzero
[ 0.880000] Number of XOR engines to use: 4
[ 0.880000] cesadev_init(c00117b0)
[ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.880000] MV Buttons Driver Load
[ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.880000] squashfs: LZMA suppport for slax.org by jro
[ 0.880000] JFFS2 version 2.2. (NAND) أ‚آ© 2001-2006 Red Hat, Inc.
[ 0.880000] io scheduler noop registered
[ 0.880000] io scheduler anticipatory registered (default)
[ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.920000] Loading Marvell Ethernet Driver:
[ 0.920000] o Cached descriptors in DRAM
[ 0.920000] o DRAM SW cache-coherency
[ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.940000] o TCP segmentation offload enabled
[ 0.940000] o Receive checksum offload enabled
[ 0.950000] o Transmit checksum offload enabled
[ 0.950000] o Network Fast Processing (Routing) supported
[ 0.960000] o Driver ERROR statistics enabled
[ 0.960000] o Driver INFO statistics enabled
[ 0.970000] o Proc tool API enabled
[ 0.970000] o Rx descripors: q0=128
[ 0.970000] o Tx descripors: q0=532
[ 0.980000] o Loading network interface(s):
[ 0.990000] o eth0, ifindex = 1, GbE port = 0
[ 0.990000] o eth1, ifindex = 2, GbE port = 1
[ 1.000000]
[ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes
[ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.010000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.030000]
[ 1.030000] Warning Sata is Powered Off
[ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 1.050000] Scanning device for bad blocks
[ 1.100000] Using static partition definition
[ 1.110000] Creating 4 MTD partitions on "nand_mtd":
[ 1.110000] 0x00000000-0x00100000 : "u-boot"
[ 1.120000] 0x00100000-0x00500000 : "uImage"
[ 1.120000] 0x00500000-0x02500000 : "root"
[ 1.130000] 0x02500000-0x08000000 : "data"
[ 1.130000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.200000] usb usb1: configuration #1 chosen from 1 choice
[ 1.210000] hub 1-0:1.0: USB hub found
[ 1.210000] hub 1-0:1.0: 1 port detected
[ 1.330000] USB Universal Host Controller Interface driver v3.0
[ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 1.760000] usb 1-1: configuration #1 chosen from 1 choice
[ 1.760000] hub 1-1:1.0: USB hub found
[ 1.770000] hub 1-1:1.0: 4 ports detected
[ 1.880000] usbcore: registered new interface driver usblp
[ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 1.890000] Initializing USB Mass Storage driver...
[ 1.890000] usbcore: registered new interface driver usb-storage
[ 1.900000] USB Mass Storage support registered.
[ 1.910000] mice: PS/2 mouse device common for all mice
[ 1.910000] i2c /dev entries driver
[ 1.910000] Linux telephony interface: v1.00
[ 1.920000] md: linear personality registered for level -1
[ 1.920000] md: raid0 personality registered for level 0
[ 1.930000] md: raid1 personality registered for level 1
[ 2.100000] raid6: int32x1 97 MB/s
[ 2.270000] raid6: int32x2 114 MB/s
[ 2.440000] raid6: int32x4 122 MB/s
[ 2.610000] raid6: int32x8 110 MB/s
[ 2.610000] raid6: using algorithm int32x4 (122 MB/s)
[ 2.610000] md: raid6 personality registered for level 6
[ 2.620000] md: raid5 personality registered for level 5
[ 2.620000] md: raid4 personality registered for level 4
[ 2.630000] raid5: measuring checksumming speed
[ 2.680000] arm4regs : 1084.000 MB/sec
[ 2.730000] 8regs : 754.800 MB/sec
[ 2.780000] 32regs : 900.000 MB/sec
[ 2.780000] raid5: using function: arm4regs (1084.000 MB/sec)
[ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 2.790000] dm_crypt using the OCF package.
[ 2.800000] sdhci: Secure Digital Host Controller Interface driver
[ 2.800000] sdhci: Copyright(c) Pierre Ossman
[ 2.810000] usbcore: registered new interface driver usbhid
[ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 2.820000] TCP cubic registered
[ 2.820000] NET: Registered protocol family 1
[ 2.830000] NET: Registered protocol family 17
[ 2.830000] md: Autodetecting RAID arrays.
[ 2.840000] md: autorun ...
[ 2.840000] md: ... autorun DONE.
[ 3.070000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 3.070000] Freeing init memory: 124K
[ 3.070000] Warning: unable to open an initial console.
[ 3.080000] Kernel panic - not syncing: No init found. Try passing init= option to kernel.
[ 3.090000] Scheduling watchdog timeout to force reboot...


U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x200000

Reading data from 0x2ff800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2010-10-19 23:05:02 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1979140 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux............................................................................................................................ done, booting the kernel.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total
[ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init)
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] NET: Registered protocol family 16
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e8000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] INTER_REGS ....base f1000000, size 1MB
[ 0.250000] NFLASH_CS ....base fa000000, size 2MB
[ 0.250000] SPI_CS ....base f4000000, size 16MB
[ 0.250000] BOOT_ROM_CS ....no such
[ 0.250000] DEV_BOOTCS ....no such
[ 0.250000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.250000]
[ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.250000]
[ 0.250000] Detected Tclk 200000000 and SysClk 400000000
[ 0.250000] MV Buttons Device Load
[ 0.250000] Marvell USB EHCI Host controller #0: c0652600
[ 0.750000] PEX0 interface detected no Link.
[ 0.750000] PCI: bus0: Fast back to back transfers enabled
[ 0.750000] SCSI subsystem initialized
[ 0.750000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.750000] NET: Registered protocol family 2
[ 0.760000] Time: kw_clocksource clocksource has been installed.
[ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.850000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.850000] TCP reno registered
[ 0.880000] RTC has been updated!!!
[ 0.880000] RTC registered
[ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.880000] o RAID 5 Xor calculation
[ 0.880000] o kernel memcpy
[ 0.880000] o kenrel memzero
[ 0.880000] Number of XOR engines to use: 4
[ 0.880000] cesadev_init(c00117b0)
[ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.880000] MV Buttons Driver Load
[ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.880000] squashfs: LZMA suppport for slax.org by jro
[ 0.880000] JFFS2 version 2.2. (NAND) أ‚آ© 2001-2006 Red Hat, Inc.
[ 0.880000] io scheduler noop registered
[ 0.880000] io scheduler anticipatory registered (default)
[ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.920000] Loading Marvell Ethernet Driver:
[ 0.920000] o Cached descriptors in DRAM
[ 0.920000] o DRAM SW cache-coherency
[ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.940000] o TCP segmentation offload enabled
[ 0.940000] o Receive checksum offload enabled
[ 0.950000] o Transmit checksum offload enabled
[ 0.950000] o Network Fast Processing (Routing) supported
[ 0.960000] o Driver ERROR statistics enabled
[ 0.960000] o Driver INFO statistics enabled
[ 0.970000] o Proc tool API enabled
[ 0.970000] o Rx descripors: q0=128
[ 0.970000] o Tx descripors: q0=532
[ 0.980000] o Loading network interface(s):
[ 0.990000] o eth0, ifindex = 1, GbE port = 0
[ 0.990000] o eth1, ifindex = 2, GbE port = 1
[ 1.000000]
[ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes
[ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.010000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.030000]
[ 1.030000] Warning Sata is Powered Off
[ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.040000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 1.050000] Scanning device for bad blocks
[ 1.100000] Using static partition definition
[ 1.110000] Creating 4 MTD partitions on "nand_mtd":
[ 1.110000] 0x00000000-0x00100000 : "u-boot"
[ 1.120000] 0x00100000-0x00500000 : "uImage"
[ 1.120000] 0x00500000-0x02500000 : "root"
[ 1.130000] 0x02500000-0x08000000 : "data"
[ 1.130000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.140000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.180000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.200000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.200000] usb usb1: configuration #1 chosen from 1 choice
[ 1.210000] hub 1-0:1.0: USB hub found
[ 1.210000] hub 1-0:1.0: 1 port detected
[ 1.330000] USB Universal Host Controller Interface driver v3.0
[ 1.610000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 1.760000] usb 1-1: configuration #1 chosen from 1 choice
[ 1.760000] hub 1-1:1.0: USB hub found
[ 1.770000] hub 1-1:1.0: 4 ports detected
[ 1.880000] usbcore: registered new interface driver usblp
[ 1.880000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 1.890000] Initializing USB Mass Storage driver...
[ 1.890000] usbcore: registered new interface driver usb-storage
[ 1.900000] USB Mass Storage support registered.
[ 1.910000] mice: PS/2 mouse device common for all mice
[ 1.910000] i2c /dev entries driver
[ 1.910000] Linux telephony interface: v1.00
[ 1.920000] md: linear personality registered for level -1
[ 1.920000] md: raid0 personality registered for level 0
[ 1.930000] md: raid1 personality registered for level 1
[ 2.100000] raid6: int32x1 97 MB/s
[ 2.270000] raid6: int32x2 114 MB/s
[ 2.440000] raid6: int32x4 122 MB/s
[ 2.610000] raid6: int32x8 110 MB/s
[ 2.610000] raid6: using algorithm int32x4 (122 MB/s)
[ 2.610000] md: raid6 personality registered for level 6
[ 2.620000] md: raid5 personality registered for level 5
[ 2.620000] md: raid4 personality registered for level 4
[ 2.630000] raid5: measuring checksumming speed
[ 2.680000] arm4regs : 1071.600 MB/sec
[ 2.730000] 8regs : 754.800 MB/sec
[ 2.780000] 32regs : 900.000 MB/sec
[ 2.780000] raid5: using function: arm4regs (1071.600 MB/sec)
[ 2.790000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 2.790000] dm_crypt using the OCF package.
[ 2.800000] sdhci: Secure Digital Host Controller Interface driver
[ 2.800000] sdhci: Copyright(c) Pierre Ossman
[ 2.810000] usbcore: registered new interface driver usbhid
[ 2.810000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 2.820000] TCP cubic registered
[ 2.820000] NET: Registered protocol family 1
[ 2.830000] NET: Registered protocol family 17
[ 2.830000] md: Autodetecting RAID arrays.
[ 2.840000] md: autorun ...
[ 2.840000] md: ... autorun DONE.
[ 3.070000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 3.070000] Freeing init memory: 124K
[ 3.070000] Warning: unable to open an initial console.
[ 3.080000] Kernel panic - not syncing: No init found. Try passing init= option to kernel.
[ 3.090000] Scheduling watchdog timeout to force reboot...


U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
CE>>
CE>>
CE>>
')


now i need to know how to fix this issue to run ARM on this box or to return to the default pogoplug image.

Waiting for your help

thanks

[Geoff]

So it looks like it's using the stock uboot and the stock kernel, but then it tries to use the stock rootfs and that's messed up. There should be a way to fix this. If you can somehow put a minimal compatible rootfs somewhere that the kernel has the ability to access it (I don't know where), then you could change the bootargs to look for that instead. It might be possible to boot using tftp. Failing that, it might be possible to use uboot to copy a rootfs over serial, but that's a job for an expert.

[msanad]

Hello Geoff

can you tell me how to add rootfs using tftp , i can use serial connection and already install tftp server and used it.

[Geoff]

I don't actually have an E02. I hope someone who has done this before will respond.

[moonman]

follow this guide to get uboot (the manual way)
http://forum.doozan.com/read.php?3,6965,6965

and the follow the link in my signature (reinstailling from scratch) to a make a bootable media.

You erased rootfs instead of uboot, and you are lucky that it happened because if you erased uboot without flashing a new one you would have a brick recoverable only with jtag.

Never force update anything if you don't exactly know what you are doing.

[msanad]

I have made the instruction as stated in the topic , but after erasing the NAND and write the new uboot , then reboot , it hanged .

check the blow logs

$this->bbcode_second_pass_code('', '
CE>> setenv ipaddr 192.168.1.3
CE>> setenv serverip 192.168.1.2
CE>> tftpboot 0x800000 uboot.mtd0.kwb
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.3
Filename 'uboot.mtd0.kwb'.
Load address: 0x800000
Loading: T T #################################################################
######################################
done
Bytes transferred = 524288 (80000 hex)
CE>>
Using egiga0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.3
Filename 'uboot.mtd0.kwb'.
Load address: 0x800000
Loading: #################################################################
######################################
done
Bytes transferred = 524288 (80000 hex)
CE>> nand erase 0x0 0x80000

NAND erase: device 0 offset 0x0, size 0x80000
Erasing at 0x60000 -- 100% complete.
OK
CE>> nand write.e 0x800000 0x0 0x80000

NAND write: device 0 offset 0x0, size 0x80000

Writing data at 0x7f800 -- 100% complete.
524288 bytes written: OK
CE>> reset


U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x300000
3145728 bytes read: OK
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-2.6.22.18
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1978544 Bytes = 1.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux............................................................................................................................ done, booting the kernel.


U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
u-boot>>
u-boot>>
u-boot>>
u-boot>>
u-boot>>
u-boot>>
u-boot>>
u-boot>> printenv
arcNumber=2097
baudrate=115200
bootargs_root=root=/dev/mtdblock2 ro
bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000
bootcmd_pogo=fsload uboot-original-mtd0.kwb; go 0x800200
bootcmd_usb=run usb_init; run usb_load_uimage; run set_bootargs_usb; run usb_boot;
bootdelay=3
console=console=ttyS0,115200
ethact=egiga0
ethaddr=00:25:31:04:A2:18
ipaddr=192.168.1.4
led_error=orange blinking
led_exit=green off
led_init=green blinking
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
serverip=192.168.1.3
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts
stderr=serial
stdin=serial
stdout=serial
usb_boot=if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000;else bootm 0x800000;fi;
usb_device=0:1
usb_init=usb start
usb_load_uimage=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext2

Environment size: 1152/131068 bytes
u-boot>>
')

[moonman]

it won't boot unless you have a usb media with rootfs inserted. You erased the original one in nand.