not able to boot in arch goflex

[nick2012]

my goflex not recognizing my hard disk with arch linux installed.
it constantly booting in rescue mode.
thanks

[WarheadsSE]

Check the label of the rootfs partition.

[nick2012]

label is rootfs

[nick2012]

Bump need help guys

[moonman]

Setup netconsole. We will need your
boot log, and your u-boot environment.

[nick2012]

got this with netconsole

$this->bbcode_second_pass_code('', 'U-Boot 2011.12 (Apr 18 2012 - 23:08:20)
Seagate GoFlexNet
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..

Reset IDE: ide_preinit failed
** Bad partition 1 **
** Bad partition 1 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!

NAND read: device 0 offset 0x100000, size 0x400000
4194304 bytes read: OK
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.3.2-kirkwide
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3627768 Bytes = 3.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...
')

[WarheadsSE]

How is the disk attached, how big is it, and is it partitioned with GPT, MBR or Hybrid?

[nick2012]

$this->bbcode_second_pass_quote('WarheadsSE', 'H')ow is the disk attached, how big is it, and is it partitioned with GPT, MBR or Hybrid?

[WarheadsSE]

It sounds to me then, that the usb enclosure & ide drive are not ready in time to make the device present to uboot.

I think there is a trick to start/stop/start the usb which might assist you.

[nick2012]

It was doing fine till now
And whats the trick??