Help with Pogoplug E02 Restore / Repair - Have Serial Access

[mrmees]

I picked up a Pogoplug a while back and had messed with it a little before putting it on the shelf.

Plugged it back in recently to try and use it for a little home server and proceeded to bork it up something fierce while trying to install Arch. It's very possible I tried to install Debian on this thing previously so maybe that's the root of the problems?

Regardless- I'd like a method to restore the E02 back to the original factory firmware so I can start the process all over again. I don't have any backups of the original image.

Here's what I get on the serial console:

$this->bbcode_second_pass_code('', 'U-Boot 2014.07-tld-2 (Sep 20 2014 - 00:52:18)
Pogo E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
No link on egiga0
ping failed; host 192.168.1.1 is not alive
Hit any key to stop autoboot: 0
Unknown command 'usb' - try 'help'
Unknown command 'mmc' - try 'help'
Unknown command 'ide' - try 'help'
USB is stopped. Please issue 'usb start' first.
Unknown command 'mmc' - try 'help'
Unknown command 'ide' - try 'help'
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Unknown command 'mmc' - try 'help'
Unknown command 'bootargs' - try 'help'
** Bad device mmc 0 **
** Bad device mmc 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Unknown command 'ide' - try 'help'
** Bad device ide 0 **
** Bad device ide 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
resetting ...
')

Any help?

[mrmees]

Here's the output from printenv - I'm sure it's embarrassing even if I can't figure out why.

$this->bbcode_second_pass_code('', 'arcNumber=3542
baudrate=115200
bootargs_root=root=/dev/mtdblock2 ro
bootcmd=run bootcmd_uenv; run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset
bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot
bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot;
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
bootm=echo Booting from ${disk} ...; run setargs; bootm ${loadaddr};
bootz=echo Booting from ${disk} ...; run setargs; bootz ${loadaddr} - ${fdt_addr};
console=ttyS0,115200
device=0:1
ethact=egiga0
ethaddr=00:25:31:04:A7:D5
fdt_addr=0x800000
fdt_file=/boot/dtbs/kirkwood-pogo_e02.dtb
if_netconsole=ping $serverip
importbootenv=echo Importing environment (uEnv.txt)...; env import -t $loadaddr $filesize
ipaddr=192.168.1.245
led_error=orange blinking
led_exit=green off
led_init=green blinking
load=echo Attempting to boot from ${type} ${disk}:1...;if run loadbootenv; then run importbootenv;fi;echo Checking if uenvcmd is set ...;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;echo Running default loadzimage ...;if run loadzimage; then run loadfdt;run bootz;fi;echo Running default loaduimage ...;if run loaduimage; then run bootm;fi;
loadaddr=0x810000
loadbootenv=load ${type} ${disk}:1 ${loadaddr} /boot/uEnv.txt
loadfdt=load ${type} ${disk}:1 ${fdt_addr} ${fdt_file}
loaduimage=load ${type} ${disk}:1 ${loadaddr} ${uimage}
loadzimage=load ${type} ${disk}:1 ${loadaddr} ${zimage}
machid=dd6
mainlineLinux=yes
mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
mmc_init=mmc rescan
mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage
mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd
mmc_root=/dev/mmcblk0p1
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
netmask=255.255.0.0
partition=nand0,2
preboot=run preboot_nc
preboot_nc=run if_netconsole start_netconsole
rootdelay=10
rootfstype=ext3
sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_init=ide reset
sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage
sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd
sata_root=/dev/sda1
serverip=192.168.1.1
servip=192.168.0.100
set_bootargs_mmc=set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
setargs=setenv bootargs console=${console},${baudrate} ${optargs} root=/dev/sd${letter}1 rw rootwait ${mtdparts}
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x810000
uenv_load=usb start; mmc rescan; ide reset; setenv uenv_loaded 0; for devtype in usb mmc ide; do for disknum in 0; do run uenv_read_disk; done; done
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
uimage=/boot/uImage
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1
zimage=/boot/zImage
')