Hi, I tried installing ArchLinux on a Pogoplug 02 and managed to mess it up. I've been reading the various forums for quite a while to see if I can figure out how to resurrect it. I just don't know enough about Linux to figure it out. Would really appreciate any help I could get. Any chance to revert back to original? I am able to access via serial connection and have the following:
$this->bbcode_second_pass_code('', 'U-Boot 2014.04.R3-1 (May 26 2014 - 19:45:55) Arch Linux ARM
Pogo E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 2048 8388608 e2ff6f0c-01 83
2 8390656 -396328784 e2ff6f0c-02 83
Attempting to boot from usb 0:1...
** File not found /boot/uEnv.txt **
Checking if uenvcmd is set ...
Running default loadzimage ...
** File not found /boot/zImage **
Running default loaduimage ...
4603360 bytes read in 403 ms (10.9 MiB/s)
Booting from 0 ...
## Booting kernel from Legacy Image at 00810000 ...
Image Name: Linux-4.4.28-1-ARCH
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4603296 Bytes = 4.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.28-1-ARCH (builduser@leming) (gcc version 6.2.1 20160830 (GCC) ) #1 PREEMPT Sat Oct 29 00:27:49 MDT 2016
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Pogoplug E02
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rw rootwait mtdparts=orion_nand:1M(u-boot),-(rootfs)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 249516K/262144K available (6597K kernel code, 547K rwdata, 1876K rodata, 300K init, 725K bss, 12628K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc084e9a4 (8475 kB)
[ 0.000000] .init : 0xc084f000 - 0xc089a000 ( 300 kB)
[ 0.000000] .data : 0xc089a000 - 0xc0922e0c ( 548 kB)
[ 0.000000] .bss : 0xc0922e0c - 0xc09d83d8 ( 726 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:114
[ 0.000013] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 13.346321] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 13.346510] Console: colour dummy device 80x30
[ 13.346537] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 13.436404] pid_max: default: 32768 minimum: 301
[ 13.436499] Security Framework initialized
[ 13.436575] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 13.436593] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 13.437343] Initializing cgroup subsys io
[ 13.437375] Initializing cgroup subsys memory
[ 13.437427] Initializing cgroup subsys devices
[ 13.437453] Initializing cgroup subsys freezer
[ 13.437475] Initializing cgroup subsys net_cls
[ 13.437493] Initializing cgroup subsys perf_event
[ 13.437515] Initializing cgroup subsys net_prio
[ 13.437597] CPU: Testing write buffer coherency: ok
[ 13.438060] Setting up static identity map for 0x81e0 - 0x8238
[ 13.440020] devtmpfs: initialized
[ 13.442351] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 13.442789] pinctrl core: initialized pinctrl subsystem
[ 13.443580] NET: Registered protocol family 16
[ 13.444079] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 13.466412] cpuidle: using governor ladder
[ 13.496409] cpuidle: using governor menu
[ 13.496591] Kirkwood: MV88F6281-A0, TCLK=200000000.
[ 13.496614] Feroceon L2: Enabling L2
[ 13.496653] Feroceon L2: Cache support initialised.
[ 13.537912] vgaarb: loaded
[ 13.538244] SCSI subsystem initialized
[ 13.538729] usbcore: registered new interface driver usbfs
[ 13.538804] usbcore: registered new interface driver hub
[ 13.538864] usbcore: registered new device driver usb
[ 13.539035] pps_core: LinuxPPS API ver. 1 registered
[ 13.539044] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 13.539079] PTP clock support registered
[ 13.540132] clocksource: Switched to clocksource orion_clocksource
[ 13.578864] FS-Cache: Loaded
[ 13.592093] NET: Registered protocol family 2
[ 13.592912] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 13.592950] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 13.592981] TCP: Hash tables configured (established 2048 bind 2048)
[ 13.593055] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 13.593078] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 13.593268] NET: Registered protocol family 1
[ 13.593594] RPC: Registered named UNIX socket transport module.
[ 13.593606] RPC: Registered udp transport module.
[ 13.593612] RPC: Registered tcp transport module.
[ 13.593619] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 13.595658] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 13.608370] VFS: Disk quotas dquot_6.6.0
[ 13.608635] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 13.610775] FS-Cache: Netfs 'nfs' registered for caching
[ 13.611887] NFS: Registering the id_resolver key type
[ 13.611939] Key type id_resolver registered
[ 13.611947] Key type id_legacy registered
[ 13.612032] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 13.613338] fuse init (API version 7.23)
[ 13.615571] aufs 4.4-20160912
[ 13.621041] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 13.621067] io scheduler noop registered
[ 13.621082] io scheduler deadline registered
[ 13.621356] io scheduler cfq registered
[ 13.621619] io scheduler bfq registered (default)
[ 13.621629] BFQ I/O-scheduler: v7r11
[ 13.621824] mv_xor mv_xor.0: Marvell shared XOR driver
[ 13.661395] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy )
[ 13.661643] mv_xor mv_xor.1: Marvell shared XOR driver
[ 13.701431] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy )
[ 13.707097] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 13.708224] console [ttyS0] disabled
[ 13.728337] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A
[ 14.280990] console [ttyS0] enabled
[ 14.300431] brd: module loaded
[ 14.311318] loop: module loaded
[ 14.315546] nand: Could not find valid ONFI parameter page; aborting
[ 14.322068] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 14.328452] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 14.332933] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 14.340555] Scanning device for bad blocks
[ 14.422263] 2 cmdlinepart partitions found on MTD device orion_nand
[ 14.428558] Creating 2 MTD partitions on "orion_nand":
[ 14.433743] 0x000000000000-0x000000100000 : "u-boot"
[ 14.439217] 0x000000100000-0x000008000000 : "rootfs"
[ 14.451746] libphy: orion_mdio_bus: probed
[ 14.455959] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 15.541060] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:86:a9
[ 15.549944] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 15.556536] ehci-pci: EHCI PCI platform driver
[ 15.561086] ehci-orion: EHCI orion driver
[ 15.565189] orion-ehci orion-ehci.0: EHCI Host Controller
[ 15.570664] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 15.578412] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 15.600163] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 15.607082] hub 1-0:1.0: USB hub found
[ 15.610946] hub 1-0:1.0: 1 port detected
[ 15.615594] usbcore: registered new interface driver uas
[ 15.621124] usbcore: registered new interface driver usb-storage
[ 15.627213] usbcore: registered new interface driver ums-alauda
[ 15.633263] usbcore: registered new interface driver ums-cypress
[ 15.639349] usbcore: registered new interface driver ums-datafab
[ 15.645459] usbcore: registered new interface driver ums_eneub6250
[ 15.651743] usbcore: registered new interface driver ums-freecom
[ 15.657826] usbcore: registered new interface driver ums-isd200
[ 15.663848] usbcore: registered new interface driver ums-jumpshot
[ 15.670017] usbcore: registered new interface driver ums-karma
[ 15.675951] usbcore: registered new interface driver ums-onetouch
[ 15.682172] usbcore: registered new interface driver ums-realtek
[ 15.688260] usbcore: registered new interface driver ums-sddr09
[ 15.694283] usbcore: registered new interface driver ums-sddr55
[ 15.700305] usbcore: registered new interface driver ums-usbat
[ 15.706616] mousedev: PS/2 mouse device common for all mice
[ 15.930163] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 16.082804] hub 1-1:1.0: USB hub found
[ 16.086927] hub 1-1:1.0: 4 ports detected
[ 16.370157] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[ 16.482712] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 16.489253] usb-storage 1-1.1:1.0: Quirks match for vid 152d pid 2329: 8020
[ 16.496374] scsi host0: usb-storage 1-1.1:1.0
[ 16.720156] rtc-mv rtc-mv: internal RTC not ticking
[ 16.725208] i2c /dev entries driver
[ 16.729304] sdhci: Secure Digital Host Controller Interface driver
[ 16.735539] sdhci: Copyright(c) Pierre Ossman
[ 16.739982] sdhci-pltfm: SDHCI platform and OF driver helper
[ 16.746195] ledtrig-cpu: registered to indicate activity on CPUs
[ 16.752402] usbcore: registered new interface driver r8712u
[ 16.758248] gre: GRE over IPv4 demultiplexor driver
[ 16.763217] NET: Registered protocol family 17
[ 16.767814] Key type dns_resolver registered
[ 16.773116] registered taskstats version 1
[ 16.779110] Key type encrypted registered
[ 16.783774] console [netcon0] enabled
[ 16.787458] netconsole: network logging started
[ 16.792161] hctosys: unable to open rtc device (rtc0)
[ 16.798448] Waiting for root device /dev/sda1...
[ 17.501270] scsi 0:0:0:0: Direct-Access ST2000DL 003-9VT166 PQ: 0 ANSI: 2 CCS
[ 17.511262] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 17.519165] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 17.525135] sd 0:0:0:0: [sda] Write Protect is off
[ 17.530818] sd 0:0:0:0: [sda] No Caching mode page found
[ 17.536190] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 17.545649] sda: sda1 sda2
[ 17.551707] sd 0:0:0:0: [sda] Attached SCSI disk
[ 17.571475] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 17.601726] EXT4-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
[ 17.611561] EXT4-fs (sda1): recovery complete
[ 17.615947] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 17.623723] VFS: Mounted root (ext3 filesystem) on device 8:1.
[ 17.637393] devtmpfs: mounted
[ 17.641600] Freeing unused kernel memory: 300K (c084f000 - c089a000)
[ 17.716254] Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[ 17.729452] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.28-1-ARCH #1
[ 17.735827] Hardware name: Pogoplug E02
[ 17.739701] [<c0010524>] (unwind_backtrace) from [<c000d9d0>] (show_stack+0x10/0x14)
[ 17.747488] [<c000d9d0>] (show_stack) from [<c00cd81c>] (panic+0x88/0x208)
[ 17.754406] [<c00cd81c>] (panic) from [<c0647368>] (kernel_init+0xc4/0xe8)
[ 17.761315] [<c0647368>] (kernel_init) from [<c000a4d0>] (ret_from_fork+0x14/0x24)
[ 17.768920] ---[ end Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
')