bricked GoFlex Net, need help!

[anesthetic]

I followed official installation with ubit 0.6 and the installation failed with error, which i forgot.....sad

right now my goflex net can't start...green light keeps blinking...guess its bricked...

So i connect usb-serial cable and take a look...the console output is as below...seems like ubit didn't get installed correctly

Any comments would be aprreciated...i really wanna bring my goflex net back.......thanks a lot pals

btw where did the official installation page go? i can't find it anymore......

U-Boot 2010.09 (Feb 16 2011 - 18:42:02)
UBIT v0.6 by Jeff Doozan and Peter Carmichael

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1750
UBI: number of bad PEBs: 2
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1729
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:silent", error -19
Error reading superblock on volume 'ubi:silent'!
UBIFS not mounted, use ubifs mount to mount volume first!
Using egiga0 device
ping failed; host 10.10.10.5 is not alive
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:fast", error -19
Error reading superblock on volume 'ubi:fast'!
UBIFS not mounted, use ubifs mount to mount volume first!
** Block device usb 0 not supported
** Block device usb 0 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 1 not supported
** Block device usb 1 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 2 not supported
** Block device usb 2 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 3 not supported
** Block device usb 3 not supported

** Invalid boot device **

** Invalid boot device **

Reset IDE: Bus 0: not available Bus 1: not available
** Bad partition 1 **
** Bad partition 1 **
No Powersaving mode 7F
Error (no IRQ) dev 0 blk 0: status 0x7f
** Can't read from device 0 **

** Unable to use ide 0:1 for fatload **
No Powersaving mode 7F
Error (no IRQ) dev 0 blk 0: status 0x7f
** Can't read from device 0 **

** Unable to use ide 0:1 for fatload **
** Bad partition 1 **
** Bad partition 1 **
No Powersaving mode 7F
Error (no IRQ) dev 1 blk 0: status 0x7f
** Can't read from device 1 **

** Unable to use ide 1:1 for fatload **
No Powersaving mode 7F
Error (no IRQ) dev 1 blk 0: status 0x7f
** Can't read from device 1 **

** Unable to use ide 1:1 for fatload **
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:ramdisk", error -19
Error reading superblock on volume 'ubi:ramdisk'!
UBIFS not mounted, use ubifs mount to mount volume first!

[WarheadsSE]

Verify your rootfs

For the directions, go to the main page, pull down the platforms menu, select armv5, goflex net. Then, once on that page click "installation"

[kmihelich]

Yes, you likely just need to repartition/format/extract the rootfs again to the drive you plan on using.

[anesthetic]

thanks guys.

so looks like ubit was installed correctly? Can I use rescue usb stick to boot it?

if yes any info how to create a rescue usb stick?

really appreciate your help:)

[anesthetic]

I created a rescue usb stick according to peaslaker's post.

But it still doesn't boot.......the printout stops at the last line, seems like goflex net freezes there and green light keeps blinking...router page doesn't show any ip from goflex....

Can somebody please take a look at the printout as below...see anything wrong

Thanks a lot!

http://pastie.org/private/cnnndvx8zblyfumcxchoxq

*moved looooong post of boot to pastie.org ~ WarheadsSE

[kmihelich]

Bootloader appears fine, please continue doing whatever you want while ignoring my suggestion that will get it booted.