Hello,
I just bricked my Zyxel NSA320. I tried install Arch Linux and something went wrong.
I connected serial cable, from old Nokia, but I don't know what next. Could somebody help me with this?
Thats what i got from terminal:
$this->bbcode_second_pass_code('', ' __ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Nov 9 2012 - 14:55:24) Marvell version: 3.4.19
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
//--- stateButtonBit = 3, recovery ---//
Kernel address is 0xc80000.
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0, egiga1 [PRIME]
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
** Bad partition 1 **
## Booting image at 02000000 ...
Bad Magic Number
NSA320>>')
NSA320>> printenv
$this->bbcode_second_pass_code('', 'bootdelay=2
baudrate=115200
loads_echo=0
eth1addr=00:19:CB:00:51:82
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=DD01
PRODUCT_NAME=NSA-320
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=ZyXEL Communications Corp.
run_diag=yes
ethaddr=28:28:5D:0A:31:C0
arcNumber=3956
bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/sda2 rw rootwait loglevel=8
bootcmd_linux=setenv bootargs $(bootargs_linux); ide reset; ext2load ide 0:1 $(loadaddr) /uImage; bootm $(loadaddr)
bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr)
to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset
to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset
console=100000
=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
CASset=min
ethprime=egiga1
bootargs_root=root=/dev/nfs rw
bootargs_end=:::orion:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
bootcmd='run bootcmd_linux'
stdin=serial
stdout=serial
stderr=serial
nandEnvBase=100000
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
MALLOC_len=3
netbsd_en=no
vxworks_en=no
disaMvPnp=no
hddPowerCtrl=no
enaAutoRecovery=yes
kernel_addr=0xc80000
pcieTune=no
ethact=egiga1
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/sda2 rw rootwait loglevel=8
Environment size: 2464/131068 bytes')