Cannot boot Arch.

This forum is for Marvell Kirkwood devices such as the GoFlex Home/Net, PogoPlug v1/v2, SheevaPlug, and ZyXEL devices.

Cannot boot Arch.

Postby funroompogo » Sat Apr 25, 2020 9:19 pm

Hi All,

I found my old pogoplug v4 in storage and decided to deploy it as a backup server in my home network. I don't remember what I did the last time I used it, but I think I messed something up and I am unable to boot into Arch. I have a netconsole session set up. I'm currently using Uboot 2016.09.01-1.

printenv

Code: Select all
printenv
bootcmd=run startboot;run bootubi
bootdir=/boot
bootfilem=uImage
bootfilez=zImage
bootpart=1:1
bootubi=echo Trying to boot from NAND ...;if run mountubi; then ubifsload ${loadaddr} /boot/zImage;ubifsload ${fdtaddr} /boot/dtbs/kirkwood-pogoplugv4.dtb; ubifsumount; setenv bootargs console=${console} ubi.mtd=1 root=ubi0:rootfs ro rootfstype=ubifs  rootwait ${mtdparts};bootz ${loadaddr} - ${fdtaddr};fi
console=ttyS0,115200
devnum=2
ethact=egiga0
ethaddr=00:25:31:05:08:77
fdtaddr=0x800000
fdtdir=/boot/dtbs
fdtfile=kirkwood-pogoplug-series-4.dtb
ipaddr=10.10.10.3
loadaddr=0x810000
loadfdt=echo loading ${fdtdir}/${fdtfile} ...; load ${devtype} ${bootpart} ${fdtaddr} ${fdtdir}/${fdtfile}
loadimage=load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/${bootfilez} || load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/${bootfilem}
loadrd=load ${devtype} ${bootpart} ${rdaddr} ${bootdir}/${rdfile}
mainargs=setenv bootargs console=${console} ${mtdparts} root=${root} rw rootwait ${optargs} ${ncargs}
mountubi=ubi part rootfs; ubifsmount ubi0:rootfs
mtddevname=u-boot
mtddevnum=0
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),-(rootfs)
ncargs=ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/
ncip=10.10.10.5
ncipk=10.10.10.4
netconsole=on
partition=nand0,0
preboot=if env exists netconsole && test ${netconsole} = on; then if ping ${ncip}; then  setenv stdin nc; setenv stdout nc;  setenv stderr nc; version; if env exists ncargsusr; then echo ncargs has been defined by user; setenv ncargs ${ncargsusr}; else setenv ncargs ignore_loglevel netconsole=6665@${ipaddr}/eth0,6666@${ncipk}/; fi; fi; else echo Netconsole has been turned off.; echo To turn it on, set netconsole variable to on.; setenv stdin; setenv stdout; setenv stderr; setenv ncargs; fi
rdaddr=0x1100000
rdfile=initramfs-linux.img
startboot=usb start; ide reset; for devtype in mmc usb ide; do  setenv devnum 0; while ${devtype} dev ${devnum}; do  echo ${devtype} found on device ${devnum}; setenv bootpart ${devnum}:1; echo Checking for: ${bootdir}/uEnv.txt ...; if test -e ${devtype} ${bootpart} ${bootdir}/uEnv.txt; then  load ${devtype} ${bootpart} ${loadaddr} ${bootdir}/uEnv.txt; env import -t ${loadaddr} ${filesize}; echo Loaded environment from ${bootdir}/uEnv.txt; echo Checking if uenvcmd is set ...; if test -n ${uenvcmd}; then  echo Running uenvcmd ...; run uenvcmd; fi; fi; if run loadimage; then if env exists root; then echo root has been defined by user; else part uuid ${devtype} ${bootpart} uuid; setenv root PARTUUID=${uuid}; fi;  run mainargs; if run loadfdt; then  if run loadrd; then  bootz ${loadaddr} ${rdaddr}:${filesize} ${fdtaddr}; else  bootz ${loadaddr} - ${fdtaddr}; fi; else  if run loadrd; then echo Booting uImage with initrd;  bootm ${loadaddr} ${rdaddr}:${filesize}; else  bootm ${loadaddr}; fi; fi; else  echo No kernel found; fi; setexpr devnum ${devnum} + 1; done; done;
stderr=nc
stdin=nc
stdout=nc
usb_pgood_delay=10000

Environment size: 3032/131068 bytes


This is what I get when I try to boot
Code: Select all
boot
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Reset IDE: ide_preinit failed
Card did not respond to voltage select!

USB device 0:
    Device 0: Vendor: Generic  Rev: 8.07 Prod: Flash Disk     
            Type: Removable Hard Disk
            Capacity: 3840.0 MB = 3.7 GB (7864320 x 512)
... is now current device
usb found on device 0
Checking for: /boot/uEnv.txt ...
** File not found /boot/zImage **
4622488 bytes read in 439 ms (10 MiB/s)
loading /boot/dtbs/kirkwood-pogoplug-series-4.dtb ...
** File not found /boot/dtbs/kirkwood-pogoplug-series-4.dtb **
EHCI timed out on TD - token=0xbe008d80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
 ** ext4fs_devread read error - block
## Booting kernel from Legacy Image at 00810000 ...
   Image Name:   Linux-4.4.213-1-ARCH
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4622424 Bytes = 4.4 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK


And this on

Code: Select all
[    0.000000]   Normal zone: 288 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:1M(u-boot),-(rootfs) root=PARTUUID=b49133e9-01 rw rootwait ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119664K/131072K available (6614K kernel code, 548K rwdata, 1892K rodata, 300K init, 720K bss, 11408K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0856bbc   (8507 kB)
[    0.000000]       .init : 0xc0857000 - 0xc08a2000   ( 300 kB)
[    0.000000]       .data : 0xc08a2000 - 0xc092b29c   ( 549 kB)
[    0.000000]        .bss : 0xc092b29c - 0xc09df428   ( 721 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]    Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:114
[    0.000018] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[   17.907432] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[   17.907715] Console: colour dummy device 80x30
[   17.907753] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[   17.997535] pid_max: default: 32768 minimum: 301
[   17.997666] Security Framework initialized
[   17.997774] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   17.997798] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   17.998888] Initializing cgroup subsys io
[   17.998936] Initializing cgroup subsys memory
[   17.999013] Initializing cgroup subsys devices
[   17.999052] Initializing cgroup subsys freezer
[   17.999083] Initializing cgroup subsys net_cls
[   17.999111] Initializing cgroup subsys perf_event
[   17.999143] Initializing cgroup subsys net_prio
[   17.999258] CPU: Testing write buffer coherency: ok
[   17.999955] Setting up static identity map for 0x81e0 - 0x8238
[   18.002905] devtmpfs: initialized
[   18.006614] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[   18.006671] futex hash table entries: 256 (order: -1, 3072 bytes)
[   18.007466] pinctrl core: initialized pinctrl subsystem
[   18.008647] NET: Registered protocol family 16
[   18.009514] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   18.037564] cpuidle: using governor ladder
[   18.067562] cpuidle: using governor menu
[   18.067876] Kirkwood: MV88F6281-A1, TCLK=166666667.
[   18.067912] Feroceon L2: Enabling L2
[   18.067962] Feroceon L2: Cache support initialised.
[   18.069032] initial MPP regs: 01111111 11113322 00551111 00100000 00000000 00000000 00000000
[   18.069072]   final MPP regs: 01111111 11113322 00551111 00000000 00000000 00000000 00000000
[   18.071339] Kirkwood PCIe port 0: link up
[   18.071353] PCI: bus0 uses PCIe port 0
[   18.071688] PCI host bridge to bus 0000:00
[   18.071714] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[   18.071731] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[   18.071747] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[   18.071794] pci 0000:00:00.0: [11ab:6281] type 00 class 0x058000
[   18.071844] pci 0000:00:00.0: reg 0x10: [mem 0xd0000000-0xd00fffff 64bit pref]
[   18.071867] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x07ffffff]
[   18.071945] pci 0000:00:00.0: supports D1 D2
[   18.072269] pci 0000:00:01.0: [1b73:1009] type 00 class 0x0c0330
[   18.072334] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[   18.072365] pci 0000:00:01.0: reg 0x18: [mem 0x00000000-0x00000fff 64bit]
[   18.072395] pci 0000:00:01.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit]
[   18.072473] pci 0000:00:01.0: supports D1
[   18.072489] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[   18.072871] PCI: bus0: Fast back to back transfers disabled
[   18.072893] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[   18.072941] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[   18.072972] pci 0000:00:01.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[   18.073002] pci 0000:00:01.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[   18.109730] vgaarb: loaded
[   18.110209] SCSI subsystem initialized
[   18.110480] libata version 3.00 loaded.
[   18.110933] usbcore: registered new interface driver usbfs
[   18.111051] usbcore: registered new interface driver hub
[   18.111135] usbcore: registered new device driver usb
[   18.111368] pps_core: LinuxPPS API ver. 1 registered
[   18.111381] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[   18.111426] PTP clock support registered
[   18.113056] clocksource: Switched to clocksource orion_clocksource
[   18.170300] FS-Cache: Loaded
[   18.188826] NET: Registered protocol family 2
[   18.189952] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[   18.189990] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[   18.190019] TCP: Hash tables configured (established 1024 bind 1024)
[   18.190127] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   18.190159] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   18.190448] NET: Registered protocol family 1
[   18.190914] RPC: Registered named UNIX socket transport module.
[   18.190930] RPC: Registered udp transport module.
[   18.190939] RPC: Registered tcp transport module.
[   18.190948] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   18.191022] pci 0000:00:01.0: enabling device (0140 -> 0142)
[   18.191129] PCI: CLS 32 bytes, default 32
[   18.212987] VFS: Disk quotas dquot_6.6.0
[   18.213583] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   18.216578] FS-Cache: Netfs 'nfs' registered for caching
[   18.218233] NFS: Registering the id_resolver key type
[   18.218302] Key type id_resolver registered
[   18.218313] Key type id_legacy registered
[   18.218439] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[   18.220314] fuse init (API version 7.23)
[   18.223537] aufs 4.4-20170911
[   18.231240] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[   18.231267] io scheduler noop registered
[   18.231284] io scheduler deadline registered
[   18.231679] io scheduler cfq registered
[   18.232051] io scheduler bfq registered (default)
[   18.232063] BFQ I/O-scheduler: v7r11
[   18.232371] mv_xor mv_xor.0: Marvell shared XOR driver
[   18.274795] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy )
[   18.275135] mv_xor mv_xor.1: Marvell shared XOR driver
[   18.314700] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy )
[   18.322760] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   18.324308] console [ttyS0] disabled
[   18.344387] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[   19.092237] console [ttyS0] enabled
[   19.118811] brd: module loaded
[   19.133027] loop: module loaded
[   19.136709] sata_mv sata_mv.0: version 1.28
[   19.140941] sata_mv sata_mv.0: cannot get optional clkdev
[   19.146466] sata_mv sata_mv.0: slots 32 ports 1
[   19.153467] scsi host0: sata_mv
[   19.157130] ata1: SATA max UDMA/133 irq 21
[   19.162369] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[   19.168741] nand: Hynix H27U1G8F2BTR-BC
[   19.172563] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[   19.180155] Scanning device for bad blocks
[   19.261115] Bad eraseblock 939 at 0x000007560000
[   19.272617] 2 cmdlinepart partitions found on MTD device orion_nand
[   19.278879] Creating 2 MTD partitions on "orion_nand":
[   19.284028] 0x000000000000-0x000000100000 : "u-boot"
[   19.289691] 0x000000100000-0x000008000000 : "rootfs"
[   19.305216] libphy: orion_mdio_bus: probed
[   19.309454] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   19.503098] ata1: SATA link down (SStatus 0 SControl F300)
[   20.397334] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:08:77
[   20.406260] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   20.412773] ehci-pci: EHCI PCI platform driver
[   20.417333] ehci-orion: EHCI orion driver
[   20.421429] orion-ehci orion-ehci.0: EHCI Host Controller
[   20.426868] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   20.434632] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   20.453101] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   20.460443] hub 1-0:1.0: USB hub found
[   20.464300] hub 1-0:1.0: 1 port detected
[   20.469237] xhci_hcd 0000:00:01.0: xHCI Host Controller
[   20.474554] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[   20.483501] xhci_hcd 0000:00:01.0: hcc params 0x200073a1 hci version 0x100 quirks 0x00080010
[   20.493308] hub 2-0:1.0: USB hub found
[   20.497094] hub 2-0:1.0: 2 ports detected
[   20.501930] xhci_hcd 0000:00:01.0: xHCI Host Controller
[   20.507223] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 3
[   20.514740] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[   20.524032] hub 3-0:1.0: USB hub found
[   20.527814] hub 3-0:1.0: 2 ports detected
[   20.532864] usbcore: registered new interface driver uas
[   20.538481] usbcore: registered new interface driver usb-storage
[   20.544609] usbcore: registered new interface driver ums-alauda
[   20.550589] usbcore: registered new interface driver ums-cypress
[   20.556704] usbcore: registered new interface driver ums-datafab
[   20.562762] usbcore: registered new interface driver ums_eneub6250
[   20.569132] usbcore: registered new interface driver ums-freecom
[   20.575231] usbcore: registered new interface driver ums-isd200
[   20.581200] usbcore: registered new interface driver ums-jumpshot
[   20.587372] usbcore: registered new interface driver ums-karma
[   20.593462] usbcore: registered new interface driver ums-onetouch
[   20.599648] usbcore: registered new interface driver ums-realtek
[   20.605740] usbcore: registered new interface driver ums-sddr09
[   20.611709] usbcore: registered new interface driver ums-sddr55
[   20.617709] usbcore: registered new interface driver ums-usbat
[   20.624399] mousedev: PS/2 mouse device common for all mice
[   20.783097] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   20.941700] usb-storage 1-1:1.0: USB Mass Storage device detected
[   20.948268] scsi host1: usb-storage 1-1:1.0
[   21.633091] rtc-mv rtc-mv: internal RTC not ticking
[   21.638160] i2c /dev entries driver
[   21.642472] sdhci: Secure Digital Host Controller Interface driver
[   21.648663] sdhci: Copyright(c) Pierre Ossman
[   21.693388] sdhci-pltfm: SDHCI platform and OF driver helper
[   21.702888] ledtrig-cpu: registered to indicate activity on CPUs
[   21.709144] usbcore: registered new interface driver r8712u
[   21.715127] gre: GRE over IPv4 demultiplexor driver
[   21.720077] NET: Registered protocol family 17
[   21.724753] Key type dns_resolver registered
[   21.731707] registered taskstats version 1
[   21.738504] Key type encrypted registered
[   21.743526] netpoll: netconsole: local port 6665
[   21.748130] netpoll: netconsole: local IPv4 address 10.10.10.3
[   21.754017] netpoll: netconsole: interface 'eth0'
[   21.758702] netpoll: netconsole: remote port 6666
[   21.763572] netpoll: netconsole: remote IPv4 address 10.10.10.4
[   21.769503] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[   21.777418] netpoll: netconsole: device eth0 not up yet, forcing it
[   21.955018] scsi 1:0:0:0: Direct-Access     Generic  Flash Disk       8.07 PQ: 0 ANSI: 4
[   21.975104] sd 1:0:0:0: Attached scsi generic sg0 type 0
[   21.980815] sd 1:0:0:0: [sda] 7864320 512-byte logical blocks: (4.03 GB/3.75 GiB)
[   21.994930] sd 1:0:0:0: [sda] Write Protect is off
[   21.999734] sd 1:0:0:0: [sda] Mode Sense: 23 00 00 00
[   22.024183] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   22.049414]  sda: sda1
[   22.065813] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   25.798527] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   25.817599] console [netcon0] enabled
[   25.821268] netconsole: network logging started
[   25.826494] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   25.833681] hctosys: unable to open rtc device (rtc0)
[   25.842205] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   26.773112] usb 1-1: reset high-speed USB device number 2 using orion-ehci
[   26.944183] sd 1:0:0:0: [sda] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[   26.952378] sd 1:0:0:0: [sda] tag#0 Sense Key : 0x6 [current]
[   26.958235] sd 1:0:0:0: [sda] tag#0 ASC=0x28 ASCQ=0x0
[   26.963417] sd 1:0:0:0: [sda] tag#0 CDB: opcode=0x28 28 00 00 00 f9 40 00 00 30 00
[   26.971001] blk_update_request: I/O error, dev sda, sector 63808
[   26.977162] JBD2: Failed to read block at offset 6551
[   26.982211] JBD2: IO error -5 recovering block 6551 in log
[   26.987793] JBD2: Failed to read block at offset 6552
[   26.992933] JBD2: IO error -5 recovering block 6552 in log
[   26.998518] JBD2: Failed to read block at offset 6553
[   27.003633] JBD2: IO error -5 recovering block 6553 in log
[   27.009111] JBD2: Failed to read block at offset 6554
[   27.014265] JBD2: IO error -5 recovering block 6554 in log
[   27.019764] JBD2: Failed to read block at offset 6555
[   27.024856] JBD2: IO error -5 recovering block 6555 in log
[   27.030360] JBD2: Failed to read block at offset 6556
[   27.035451] JBD2: IO error -5 recovering block 6556 in log
[   27.041638] JBD2: Failed to read block at offset 6573
[   27.046778] JBD2: IO error -5 recovering block 6573 in log
[   27.052274] JBD2: Failed to read block at offset 6574
[   27.057366] JBD2: IO error -5 recovering block 6574 in log
[   27.062854] JBD2: Failed to read block at offset 6575
[   27.067947] JBD2: IO error -5 recovering block 6575 in log
[   27.073474] JBD2: Failed to read block at offset 6576
[   27.078528] JBD2: IO error -5 recovering block 6576 in log
[   27.084056] JBD2: Failed to read block at offset 6577
[   27.089103] JBD2: IO error -5 recovering block 6577 in log
[   27.094630] JBD2: Failed to read block at offset 6578
[   27.099679] JBD2: IO error -5 recovering block 6578 in log
[   27.105210] JBD2: Failed to read block at offset 6579
[   27.110262] JBD2: IO error -5 recovering block 6579 in log
[   27.115790] JBD2: Failed to read block at offset 6580
[   27.120837] JBD2: IO error -5 recovering block 6580 in log
[   27.128517] JBD2: Failed to read block at offset 6581
[   27.133645] JBD2: IO error -5 recovering block 6581 in log
[   27.139139] JBD2: Failed to read block at offset 6582
[   27.144230] JBD2: IO error -5 recovering block 6582 in log
[   27.149720] JBD2: Failed to read block at offset 6583
[   27.154812] JBD2: IO error -5 recovering block 6583 in log
[   27.160304] JBD2: Failed to read block at offset 6584
[   27.165395] JBD2: IO error -5 recovering block 6584 in log
[   27.170887] JBD2: Failed to read block at offset 6585
 ----------------------
----- Deleted this section to be within 60000 characters post
------
------------
[   53.884279] JBD2: Failed to read block at offset 9409
[   53.889331] JBD2: IO error -5 recovering block 9409 in log
[   53.900176] JBD2: recovery failed
[   53.903598] EXT4-fs (sda1): error loading journal
[   53.949360] VFS: Dirty inode writeback failed for block device sda1 (err=-5).
[   53.956814] VFS: Cannot open root device "PARTUUID=b49133e9-01" or unknown-block(8,1): error -5
[   53.965575] Please append a correct "root=" boot option; here are the available partitions:
[   53.974076] 0100            8192 ram0  (driver?)
[   53.978731] 0101            8192 ram1  (driver?)
[   53.983472] 0102            8192 ram2  (driver?)
[   53.988129] 0103            8192 ram3  (driver?)
[   53.992777] 0104            8192 ram4  (driver?)
[   53.997465] 0105            8192 ram5  (driver?)
[   54.002107] 0106            8192 ram6  (driver?)
[   54.006795] 0107            8192 ram7  (driver?)
[   54.011457] 0108            8192 ram8  (driver?)
[   54.016151] 0109            8192 ram9  (driver?)
[   54.020797] 010a            8192 ram10  (driver?)
[   54.025570] 010b            8192 ram11  (driver?)
[   54.030310] 010c            8192 ram12  (driver?)
[   54.035081] 010d            8192 ram13  (driver?)
[   54.039813] 010e            8192 ram14  (driver?)
[   54.044586] 010f            8192 ram15  (driver?)
[   54.049324] 0800         3932160 sda  driver: sd
[   54.054002]   0801         3929536 sda1 b49133e9-01
[   54.058916] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)
[   54.067159] CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.213-1-ARCH #1
[   54.073579] Hardware name: Pogoplug V4
[   54.077362] [<c000fd58>] (unwind_backtrace) from [<c000d3dc>] (show_stack+0x10/0x14)
[   54.085096] [<c000d3dc>] (show_stack) from [<c00cc808>] (panic+0x9c/0x21c)
[   54.091967] [<c00cc808>] (panic) from [<c08582c0>] (mount_block_root+0x1a0/0x24c)
[   54.099435] [<c08582c0>] (mount_block_root) from [<c085853c>] (mount_root+0xd8/0x100)
[   54.107244] [<c085853c>] (mount_root) from [<c08586c0>] (prepare_namespace+0x15c/0x1bc)
[   54.115228] [<c08586c0>] (prepare_namespace) from [<c0857e84>] (kernel_init_freeable+0x200/0x254)
[   54.124083] [<c0857e84>] (kernel_init_freeable) from [<c064b094>] (kernel_init+0x8/0xe0)
[   54.132172] [<c064b094>] (kernel_init) from [<c000a4e8>] (ret_from_fork+0x14/0x2c)
[   54.139725] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,1)


I've been messing around it with over 2 weeks now, and I think I'm making it worse, so I hope someone can help me out.

Thanks
funroompogo
 
Posts: 1
Joined: Sat Apr 25, 2020 9:00 pm

Re: Cannot boot Arch.

Postby moonman » Sun Apr 26, 2020 2:41 am

Something is up with your 4GB flash drive. Take it out and do fsck on any linux computer. it's either some compatibility problem (not likely given you had this running before), filesystem errors possibly because device lost power unexpectedly or your flash drive is failing.
Pogoplug V4 | GoFlex Home | Raspberry Pi 4 4GB | CuBox-i4 Pro | ClearFog | BeagleBone Black | Odroid U2 | Odroid C1 | Odroid XU4
-----------------------------------------------------------------------------------------------------------------------
[armv5] Updated U-Boot | [armv5] NAND Rescue System
moonman
Developer
 
Posts: 3314
Joined: Sat Jan 15, 2011 3:36 am


Return to Marvell Kirkwood

Who is online

Users browsing this forum: Google [Bot] and 7 guests