I've been trying to install Arch on my old IX2-200 following instructions here: https://kiljan.org/2016/11/15/installin ... a-ix2-200/
I cannot get it to boot, I'm completely out of my depths with Arm and could use assistance. After booting and completing all steps through Step 3, the first boot from the device itself with the 5.8 kirkwood kernel results in a boot loop. Here is some a copy and paste of the boot from console:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Sep 8 2009 - 09:31:54) Marvell version: 3.4.14
Mapower version: 2.0 (32MB) (2009/09/08)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:32 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0, egiga1 [PRIME]
Fan lookup table initialized.
Current remote temperature: 58
Current fan speed: 0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 02000000 ...
Image Name: Arch Linux ARM kernel
Created: 2020-09-13 17:00:03 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6196752 Bytes = 5.9 MB
Load Address: 02000000
Entry Point: 02000000
Verifying Checksum ... OK
XIP Kernel Image ... OK
## Loading Ramdisk Image at 08004000 ...
Image Name: Arch Linux ARM initrd
Created: 2020-09-13 18:19:02 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8634042 Bytes = 8.2 MB
Load Address: 08004000
Entry Point: 08004000
Verifying Checksum ... OK
Starting kernel ...
software interrupt
pc : [<00da8aec>] lr : [<0060020c>]
sp : 00600000 ip : 005fd844 fp : 005fd898
r10: 00000000 r9 : 005fe530 r8 : 005fffcc
r7 : 0883fefa r6 : 08004040 r5 : 006460e4 r4 : 00000000
r3 : 02000000 r2 : 00000100 r1 : 00000692 r0 : 00000000
Flags: Nzcv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Sep 8 2009 - 09:31:54) Marvell version: 3.4.14