by wpault » Thu Dec 10, 2020 1:55 pm
Yip, copying the four files from /boot into /boot/boot enables the system to boot up a little before bailing out trying to mount the root partition:
$this->bbcode_second_pass_code('', '
U-Boot 2016.09.01-1 (Oct 10 2016 - 23:14:59 -0600) Arch Linux ARM
Zyxel NSA325
SoC: Kirkwood 88F6282_A1
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
MV88E1318 PHY initialized on egiga0
IDE: Bus 0: OK Bus 1: OK
Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WMC4N0D6TTDR
Type: Hard Disk
Supports 48-bit addressing
Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WMC4N0D38VEK
Type: Hard Disk
Supports 48-bit addressing
Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
No link on egiga0
ping failed; host 10.10.10.5 is not alive
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Reset IDE: Bus 0: OK Bus 1: OK
Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WMC4N0D6TTDR
Type: Hard Disk
Supports 48-bit addressing
Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WMC4N0D38VEK
Type: Hard Disk
Supports 48-bit addressing
Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
USB device 0: unknown device
Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WMC4N0D6TTDR
Type: Hard Disk
Supports 48-bit addressing
Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
... is now current device
ide found on device 0
Checking for: /boot/uEnv.txt ...
** File not found /boot/zImage **
4662168 bytes read in 761 ms (5.8 MiB/s)
loading /boot/dtbs/kirkwood-nsa325.dtb ...
** File not found /boot/dtbs/kirkwood-nsa325.dtb **
8215137 bytes read in 1295 ms (6 MiB/s)
Booting uImage with initrd
## Booting kernel from Legacy Image at 00810000 ...
Image Name: Linux-4.4.238-1-ARCH
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4662104 Bytes = 4.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.238-1-ARCH (builduser@leming) (gcc version 10.2.0 (GCC) ) #1 PREEMPT Sat Oct 3 05:39:18 UTC 2020
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: ZyXEL NSA325 2-Bay Power Media Server
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:1M(u-boot),-(rootfs) root=PARTUUID=00f2f78e-a137-4081-b90d-8d8453c03e4b rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 500992K/524288K available (6741K kernel code, 549K rwdata, 1876K rodata, 300K init, 720K bss, 23296K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0872938 (8619 kB)
[ 0.000000] .init : 0xc0873000 - 0xc08be000 ( 300 kB)
[ 0.000000] .data : 0xc08be000 - 0xc094749c ( 550 kB)
[ 0.000000] .bss : 0xc094749c - 0xc09fb658 ( 721 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:114
[ 0.000010] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 7.155208] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 7.155372] Console: colour dummy device 80x30
[ 7.155396] Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
[ 7.245258] pid_max: default: 32768 minimum: 301
[ 7.245333] Security Framework initialized
[ 7.245401] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 7.245415] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 7.246012] Initializing cgroup subsys io
[ 7.246039] Initializing cgroup subsys memory
[ 7.246081] Initializing cgroup subsys devices
[ 7.246101] Initializing cgroup subsys freezer
[ 7.246118] Initializing cgroup subsys net_cls
[ 7.246133] Initializing cgroup subsys perf_event
[ 7.246152] Initializing cgroup subsys net_prio
[ 7.246219] CPU: Testing write buffer coherency: ok
[ 7.246603] Setting up static identity map for 0x81e0 - 0x8238
[ 7.248238] devtmpfs: initialized
[ 7.250008] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 7.250035] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 7.250423] pinctrl core: initialized pinctrl subsystem
[ 7.251085] NET: Registered protocol family 16
[ 7.251424] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 7.275281] cpuidle: using governor ladder
[ 7.305279] cpuidle: using governor menu
[ 7.305376] Kirkwood: MV88F6282-Rev-A1, TCLK=200000000.
[ 7.305396] Feroceon L2: Enabling L2
[ 7.305423] Feroceon L2: Cache support initialised.
[ 7.307098] Kirkwood PCIe port 0: link up
[ 7.307106] PCI: bus0 uses PCIe port 0
[ 7.307279] PCI host bridge to bus 0000:00
[ 7.307292] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 7.307301] pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
[ 7.307309] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 7.307933] PCI: bus0: Fast back to back transfers disabled
[ 7.307970] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit]
[ 7.336417] vgaarb: loaded
[ 7.336671] SCSI subsystem initialized
[ 7.337043] usbcore: registered new interface driver usbfs
[ 7.337103] usbcore: registered new interface driver hub
[ 7.337147] usbcore: registered new device driver usb
[ 7.337262] pps_core: LinuxPPS API ver. 1 registered
[ 7.337268] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 7.337291] PTP clock support registered
[ 7.338053] clocksource: Switched to clocksource orion_clocksource
[ 7.369298] FS-Cache: Loaded
[ 7.378671] NET: Registered protocol family 2
[ 7.379288] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 7.379343] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 7.379393] TCP: Hash tables configured (established 4096 bind 4096)
[ 7.379448] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 7.379467] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 7.379624] NET: Registered protocol family 1
[ 7.379874] RPC: Registered named UNIX socket transport module.
[ 7.379883] RPC: Registered udp transport module.
[ 7.379888] RPC: Registered tcp transport module.
[ 7.379892] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 7.379938] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 7.380232] Trying to unpack rootfs image as initramfs...
[ 7.796993] Freeing initrd memory: 8024K
[ 7.807842] VFS: Disk quotas dquot_6.6.0
[ 7.808042] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 7.809639] FS-Cache: Netfs 'nfs' registered for caching
[ 7.810499] NFS: Registering the id_resolver key type
[ 7.810545] Key type id_resolver registered
[ 7.810550] Key type id_legacy registered
[ 7.810621] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 7.811578] fuse init (API version 7.23)
[ 7.813128] aufs 4.4-20170911
[ 7.817059] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 7.817075] io scheduler noop registered
[ 7.817084] io scheduler deadline registered
[ 7.817289] io scheduler cfq registered
[ 7.817479] io scheduler bfq registered (default)
[ 7.817485] BFQ I/O-scheduler: v7r11
[ 7.817659] mv_xor mv_xor.0: Marvell shared XOR driver
[ 7.859021] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy )
[ 7.859213] mv_xor mv_xor.1: Marvell shared XOR driver
[ 7.898978] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy )
[ 7.903082] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 7.903842] console [ttyS0] disabled
[ 7.923898] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A
[ 8.542702] console [ttyS0] enabled
[ 8.557517] brd: module loaded
[ 8.566194] loop: module loaded
[ 8.569705] sata_mv sata_mv.0: cannot get optional clkdev
[ 8.575218] sata_mv sata_mv.0: slots 32 ports 2
[ 8.582071] scsi host0: sata_mv
[ 8.585618] scsi host1: sata_mv
[ 8.589056] ata1: SATA max UDMA/133 irq 21
[ 8.593169] ata2: SATA max UDMA/133 irq 21
[ 8.597869] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1
[ 8.604444] nand: Eon NAND 128MiB 3,3V 8-bit
[ 8.608750] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 8.616356] Scanning device for bad blocks
[ 8.625797] Bad eraseblock 100 at 0x000000c80000
[ 8.635686] Bad eraseblock 200 at 0x000001900000
[ 8.683558] 2 cmdlinepart partitions found on MTD device orion_nand
[ 8.689855] Creating 2 MTD partitions on "orion_nand":
[ 8.695012] 0x000000000000-0x000000100000 : "u-boot"
[ 8.700393] 0x000000100000-0x000008000000 : "rootfs"
[ 8.719221] libphy: orion_mdio_bus: probed
[ 8.723427] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 8.732789] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:00:11:22:33:44
[ 8.741710] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.748296] ehci-pci: EHCI PCI platform driver
[ 8.752805] ehci-orion: EHCI orion driver
[ 8.756893] orion-ehci orion-ehci.0: EHCI Host Controller
[ 8.762362] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 8.770102] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 8.788076] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 8.794766] hub 1-0:1.0: USB hub found
[ 8.798590] hub 1-0:1.0: 1 port detected
[ 8.803018] xhci_hcd 0000:00:01.0: xHCI Host Controller
[ 8.808319] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[ 8.816023] xhci_hcd 0000:00:01.0: hcc params 0x014042cb hci version 0x96 quirks 0x00000004
[ 8.825118] hub 2-0:1.0: USB hub found
[ 8.828959] hub 2-0:1.0: 2 ports detected
[ 8.833448] xhci_hcd 0000:00:01.0: xHCI Host Controller
[ 8.838738] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 3
[ 8.846223] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 8.855012] hub 3-0:1.0: USB hub found
[ 8.858834] hub 3-0:1.0: 2 ports detected
[ 8.863538] usbcore: registered new interface driver uas
[ 8.869043] usbcore: registered new interface driver usb-storage
[ 8.875115] usbcore: registered new interface driver ums-alauda
[ 8.881131] usbcore: registered new interface driver ums-cypress
[ 8.887199] usbcore: registered new interface driver ums-datafab
[ 8.893295] usbcore: registered new interface driver ums_eneub6250
[ 8.899613] usbcore: registered new interface driver ums-freecom
[ 8.905678] usbcore: registered new interface driver ums-isd200
[ 8.911688] usbcore: registered new interface driver ums-jumpshot
[ 8.917844] usbcore: registered new interface driver ums-karma
[ 8.923750] usbcore: registered new interface driver ums-onetouch
[ 8.930036] usbcore: registered new interface driver ums-realtek
[ 8.936107] usbcore: registered new interface driver ums-sddr09
[ 8.942100] usbcore: registered new interface driver ums-sddr55
[ 8.948161] usbcore: registered new interface driver ums-usbat
[ 8.954349] mousedev: PS/2 mouse device common for all mice
[ 9.108083] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 9.118071] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 9.128288] ata1.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133
[ 9.135030] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 9.158272] ata1.00: configured for UDMA/133
[ 9.178820] scsi 0:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5
[ 9.187659] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 9.195737] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 9.201099] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 9.206793] sd 0:0:0:0: [sda] Write Protect is off
[ 9.211728] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.270295] hub 1-1:1.0: USB hub found
[ 9.274488] hub 1-1:1.0: 4 ports detected
[ 9.282255] sda: sda1 sda2 sda3
[ 9.286874] sd 0:0:0:0: [sda] Attached SCSI disk
[ 9.708079] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 9.728300] ata2.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133
[ 9.735041] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 9.758271] ata2.00: configured for UDMA/133
[ 9.778422] scsi 1:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5
[ 9.787245] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[ 9.795313] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 9.800669] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 9.806253] sd 1:0:0:0: [sdb] Write Protect is off
[ 9.811162] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.871340] sdb: sdb1
[ 9.874665] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 9.968070] rtc-mv rtc-mv: internal RTC not ticking
[ 9.973083] i2c /dev entries driver
[ 9.977425] sdhci: Secure Digital Host Controller Interface driver
[ 9.983653] sdhci: Copyright(c) Pierre Ossman
[ 9.988089] sdhci-pltfm: SDHCI platform and OF driver helper
[ 9.994860] ledtrig-cpu: registered to indicate activity on CPUs
[ 10.001020] usbcore: registered new interface driver r8712u
[ 10.006813] gre: GRE over IPv4 demultiplexor driver
[ 10.011767] NET: Registered protocol family 17
[ 10.016320] Key type dns_resolver registered
[ 10.021335] registered taskstats version 1
[ 10.049952] Key type encrypted registered
[ 10.054517] console [netcon0] enabled
[ 10.058353] netconsole: network logging started
[ 10.063230] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 10.070288] hctosys: unable to open rtc device (rtc0)
[ 10.077075] Freeing unused kernel memory: 300K
:: running early hook [udev]
Starting version 246.6-1.1-arch
:: running hook [udev]
:: Triggering uevents...
:: performing fsck on '/dev/sda1'
boot: ignoring check interval, broken_system_clock set
boot: clean, 16/6024 files, 14050/24066 blocks
:: mounting '/dev/sda1' on real root
[ 11.391812] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[ 11.439837] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
:: running cleanup hook [udev]
ERROR: Root device mounted successfully, but /sbin/init does not exist.
Bailing out, you are on your own. Good luck.
sh: can't access tty; job control turned off
[rootfs ]# [ 126.738072] random: nonblocking pool is initialized
')