Will not reboot into Arch, but will poweron to Arch.

[jmcgee3]

I've actually had this problem in the past never got to use this Pogoplug E02 Pink. In between, I wiped everything out and started out twice using official instructions. I'm not sure where it goes awry, maybe when I install Webmin. I only have USB stick inserted, no hard drive.

In any case I finally got netboot running, this is what it looks like when coming up from powered off state (and boots correctly)
$this->bbcode_second_pass_code('', 'jmcgee@jmcgee-desktop:~$ nc.traditional -l -u -p 6666

U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt

** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 727
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 716
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
2888208 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
** File not found /boot/uInitrd
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.1.10-20-ARCH
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2888144 Bytes = 2.8 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...
')

but if I type reboot into Pogoplug SSH session, this is what it looks like on reboot. It dumps me to the pogoplug original software with that login. I can kill power and get back to archarmlinux.

$this->bbcode_second_pass_code('', 'jmcgee@jmcgee-desktop:~$ nc.traditional -l -u -p 6666

U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... EHCI timed out on TD - token=0x80008c80
unable to get device descriptor (error=-1)
3 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 727
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 716
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ......... done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...')