USB HUB Issue

[Fma965]

USB HUB Issue - Go Flex Home


Currently i have archlinuxarm on my usb pen, and boots fine.

I now need to use a non powered usb hub as i want to set up a pvr backend. when i plug the usb in to the hub it no longer boots, any ideas on how to make it boot when the pen is plugged in through the non powered usb hub?

Thanks.

[Fma965]

FW Printenv

$this->bbcode_second_pass_code('', 'ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd;$
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_boo$
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bo$
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then $
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootfstype=ext2
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000$
ethaddr=00:10:75:2d:97:83
usb_custom_params=ignore_loglevel netconsole=6665@10.10.10.3/eth0,6666@10.10.10.4/
arcNumber=3338
sata_device=0:1
sata_root=/dev/sda1
sata_rootfstype=ext3
sata_rootdelay=10
sata_set_bootargs=setenv bootargs console=$console root=$sata_root rootdelay=$sata_rootdelay rootfstype=$sata_rootfstype $mtdparts $sata_custom_params
sata_boot=ide reset; mw 0x800000 0 1; ext2load ide $sata_device 0x800000 /boot/uImage; if ext2load ide $sata_device 0x1100000 /boot/uInitrd; then bootm 0x80$
sata_bootcmd=run sata_set_bootargs; run sata_boot
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run sata_bootcmd; run rescue_bootcmd; run pogo_bootcmd; reset
usb_set_bootargs=setenv bootargs console=$console root=/dev/disk/by-label/urootfs rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_$
set_bootargs_rescue=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts
bootcmd_rescue=run set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
bootcmd_pogo=run bootcmd_rescue
rescue_installed=1
usb_rootdelay=10
')