Bricked my goflex home on ubit v0.6 (solved by peaslaker)

This forum is for Marvell Kirkwood devices such as the GoFlex Home/Net, PogoPlug v1/v2, SheevaPlug, and ZyXEL devices.

Re: Bricked my goflex home on ubit v0.6 (solved by peaslaker

Postby martymoose » Sun Aug 21, 2011 9:15 pm

ok more reading
more wasted weekend
i have read jeffs and the other guides out there
i can read the boot from a linux terminal netconsole

but following all the instructions
i carnt get it to boot from anything ubs or harddrive
comes up with error like this about block error

sorry about the formating is was pasted into something first that screwed formating

$this->bbcode_second_pass_code('', 'U-Boot 2010.09 (Feb 16 2011 – 18:44:23)
UBIT v0.6 by Jeff Doozan and Peter Carmichael (Re)start USB…
USB:Register 10011 NbrPorts 1
USB EHCI 1.00 scanning bus for devices…
2 USB Device(s) found scanning bus for storage devices…
1 Storage Device(s) found
Hit any key to stop autoboot:
0 UBIFS error (pid 0):
ubifs_get_sb:
cannot open “ubi:fast”, error -19 Error reading superblock on volume ‘ubi:fast’!
UBIFS not mounted, use ubifs mount to mount volume first!
Loading file “/boot/uImage” from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem… **
Bad ext2 partition or disk – usb 0:1 **
Loading file “/uInitrd” from usb device 0:1(usbda1)
Failed to mount ext2 filesystem… **
Bad ext2 partition or disk – usb 0:1 **
reading /boot/uImage
** Unable to read “/boot/uImage” from usb 0:1 ** reading /uInitrd
** Unable to read “/uInitrd” from usb 0:1 ** **
Block device usb 1 not supported **
Block device usb 1 not supported
** Invalid boot device **
** Invalid boot device ** **
Block device usb 2 not supported **
Block device usb 2 not supported
** Invalid boot device **
** Invalid boot device ** **
Block device usb 3 not supported **
Block device usb 3 not supported
** Invalid boot device **
** Invalid boot device **
Reset IDE: Bus 0:
OK Bus 1: not available Device 0: Model: ST32000542AS Firm: CC95 Ser#: 5XW132TA Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Loading file “/boot/uImage” from ide device 0:1 (hda1) ** ext2fs_devread() read outside partition sector -844890096 ** File not found /boot/uImage Loading file “/uInitrd” from ide device 0:1 (hda1) 4005544 bytes read UBIFS error (pid 0): ubifs_get_sb: cannot open “ubi:boot”, error -19 Error reading superblock on volume ‘ubi:boot’! UBIFS not mounted, use ubifs mount to mount volume first! reading /boot/uImage

** Unable to read “/boot/uImage” from ide 0:1 ** reading /uInitrd

** Unable to read “/uInitrd” from ide 0:1 **
** Bad partition 1 **
** Bad partition 1 **
No Powersaving mode 7F Error (no IRQ) dev 1 blk 0: status 0x7f
** Can’t read from device 1 **

** Unable to use ide 1:1 for fatload
** No Powersaving mode 7F Error (no IRQ) dev 1 blk 0: status 0x7f
** Can’t read from device 1 **
** Unable to use ide 1:1 for fatload
** UBIFS error (pid 0): ubifs_get_sb: cannot open “ubi:ramdisk”, error -19
Error reading superblock on volume ‘ubi:ramdisk’!
UBIFS not mounted, use ubifs mount to mount volume first!
Marvell>>')
its a 2tb Brick
martymoose
 
Posts: 5
Joined: Thu Aug 18, 2011 5:05 am

Re: Bricked my goflex home on ubit v0.6 (solved by peaslaker

Postby WarheadsSE » Sun Aug 21, 2011 11:34 pm

If you can get to anything its not a brick, its just not working right.
Core Developer
Remember: Arch Linux ARM is entirely community donation supported!
WarheadsSE
Developer
 
Posts: 6807
Joined: Mon Oct 18, 2010 2:12 pm

Re: Bricked my goflex home on ubit v0.6 (solved by peaslaker

Postby martymoose » Mon Aug 22, 2011 4:07 am

any ideas
i know i have to get ubit to load
but i have tried 3 usb keys to no avail
what next you reakon?
martymoose
 
Posts: 5
Joined: Thu Aug 18, 2011 5:05 am

Re: Bricked my goflex home on ubit v0.6 (solved by peaslaker

Postby martymoose » Fri Sep 02, 2011 10:05 pm

anyone?
martymoose
 
Posts: 5
Joined: Thu Aug 18, 2011 5:05 am

Re: Bricked my goflex home on ubit v0.6 (solved by peaslaker

Postby pemmafr » Wed Sep 21, 2011 10:49 pm

Hi,
i also have the same pb with mygoflex

my drive just return to stock firmware (seagate).
i've make a install on a usb disk (from linux arch for goflex home)
first my goflex boot well on usb key but it was impossible to return on goflex 'stock'
when i extract my usb key the goflex began to boot and stand for hours on green led flash
so i tried to use netconsole and my problems begans
my first key was kingston 1gb and i show that the blksize is not good (32kb!!)
so i make a tar of this key and extract to another with an ext3 2kb block
this day i put the new key in goflex (without disk 3.5)
on the first boot i was on recovery console (why i don't know)
so i found fw_setenv (witch is not in the distro arch) and make fw_setenv to modify ip @ of the netconsole on goflex
(have you done this ?)
viewtopic.php?f=23&t=200
in particular this line line :
fw_setenv preboot 'run if_netconsole start_netconsole' ?
after the reboot i came to the pb that you describe ...

to came out here's what i do :
usb start
usbboot 0:1 0 (not sure of the order type help usbboot)
boot

and my goflex boot to ubit (0.6)
by comparing the env i saw that preboot was modify in order to adjust ip for netconsole
here's my line :
fw_setenv preboot 'run ubi_start silent_boot; run nc_test nc_start; run usb_start; run if_netconsole; start_netconsole;'

you can view that all usb has return ;)

after the reboot : i was on ubit ... not on archlinux
i tried this
chain_install goflexhome
chain_revert
uboot_uptodate

there was a error message for uboot_uptodate (sorry forget to copy/paste)

so ... i reboot (my disk 1tb was in place during this phase)
and you know what : i was on original loader (from seagate)

i dont know why but for the moment i prefer this to my semi brick ;)

hope this help

good luck
pemmafr
 
Posts: 1
Joined: Wed Sep 21, 2011 10:24 pm

Previous

Return to Marvell Kirkwood

Who is online

Users browsing this forum: No registered users and 6 guests