---[ cut here]----

[Socaltom]

Ok what is this? How do I reinstall the kernel? I've had some disk errors that could be related.

$this->bbcode_second_pass_code('', '
[ 43.690000] WARNING: at kernel/softirq.c:143 local_bh_enable_ip+0x70/0xa0()
[ 43.690000] Modules linked in: gmac rt3390sta mii [last unloaded: xce]
[ 43.690000] [<c002e1fc>] (unwind_backtrace+0x0/0xe0) from [<c0048ac4>] (warn_ slowpath_common+0x48/0x60)
[ 43.690000] [<c0048ac4>] (warn_slowpath_common+0x48/0x60) from [<c004dea0>] ( local_bh_enable_ip+0x70/0xa0)
[ 43.690000] [<c004dea0>] (local_bh_enable_ip+0x70/0xa0) from [<bf0d4d44>] (Rt mpAsicSendCommandToMcu+0x458/0x4a4 [rt3390sta])
[ 43.690000] [<bf0d4d44>] (RtmpAsicSendCommandToMcu+0x458/0x4a4 [rt3390sta]) f rom [<bf064738>] (T.1819+0x2c/0x38 [rt3390sta])
[ 43.690000] [<bf064738>] (T.1819+0x2c/0x38 [rt3390sta]) from [<bf0708b4>] (As icAdjustTxPower+0x26c/0x2d5c [rt3390sta])
[ 43.690000] [<bf0708b4>] (AsicAdjustTxPower+0x26c/0x2d5c [rt3390sta]) from [< bf02a45c>] (STAMlmePeriodicExec+0x254/0xb90 [rt3390sta])
[ 43.690000] [<bf02a45c>] (STAMlmePeriodicExec+0x254/0xb90 [rt3390sta]) from [ <bf02b22c>] (MlmePeriodicExec+0x494/0x6ac [rt3390sta])
[ 43.780000] [<bf02b22c>] (MlmePeriodicExec+0x494/0x6ac [rt3390sta]) from [<bf 05d854>] (rtmp_timer_MlmePeriodicExec+0x1c/0x38 [rt3390sta])
[ 43.780000] [<bf05d854>] (rtmp_timer_MlmePeriodicExec+0x1c/0x38 [rt3390sta]) from [<c0052878>] (run_timer_softirq+0x118/0x200)
[ 43.780000] [<c0052878>] (run_timer_softirq+0x118/0x200) from [<c004dd40>] (_ _do_softirq+0xa8/0x140)
[ 43.780000] [<c004dd40>] (__do_softirq+0xa8/0x140) from [<c004e198>] (irq_exi t+0x84/0xa0)
[ 43.780000] [<c004e198>] (irq_exit+0x84/0xa0) from [<c0028290>] (do_local_tim er+0x54/0x70)
[ 43.780000] [<c0028290>] (do_local_timer+0x54/0x70) from [<c0028af8>] (__irq_ svc+0x38/0xc0)
[ 43.780000] Exception stack(0xc03cff50 to 0xc03cff98)
[ 43.780000] ff40: 00000001 00000000 c03cf f98 00000000
[ 43.780000] ff60: c03ce000 c03f5664 c03d40c4 c03ce000 c0022000 c0023180 c03d3 e08 c03f53e0
[ 43.780000] ff80: 00000000 c03cff98 c0029a1c c0029a20 60000013 ffffffff
[ 43.780000] [<c0028af8>] (__irq_svc+0x38/0xc0) from [<c0029a20>] (default_idl e+0x24/0x28)
[ 43.880000] [<c0029a20>] (default_idle+0x24/0x28) from [<c0029be8>] (cpu_idle +0x6c/0xa4)
[ 43.880000] [<c0029be8>] (cpu_idle+0x6c/0xa4) from [<c0008a10>] (start_kernel +0x31c/0x384)
[ 43.880000] [<c0008a10>] (start_kernel+0x31c/0x384) from [<60008084>] (0x6000 8084)

')

[WarheadsSE]

Why is it trying to unload sounds like it's time to get a few things from an updated tarball (oxnas-led module for example, to not us XCE) but that looks like the wireless driver taking a crap.

[Socaltom]

I disabled the wireless and the messages went away. Where can I get a clean version of the driver just to make sure mine isn't messed up?
Tom

[WarheadsSE]

Did the device halt all together? Because that error message is pretty consistent with the driver in 2.6.31 from CE

[Socaltom]

no i didnt notice any problems, it even showed up on my router. i only checked dmesg because i was checking on the ipv6 errors for the other thread.

Tom

[Socaltom]

$this->bbcode_second_pass_quote('WarheadsSE', 'W')hy is it trying to unload sounds like it's time to get a few things from an updated tarball (oxnas-led module for example, to not us XCE) but that looks like the wireless driver taking a crap.

[WarheadsSE]

once you have updated the set-oxnas-mac, then yes, xce is removable.

[Socaltom]

i copied over the whole lot of modules, did depmod - a the rebooted. then it reported my network settings were depracated. i updated rc.conf from the tarball and cleared that. then i had the blinking light issue. so i copied over the set-oxnas-mac from the tarball and ran it. all seems to be fine now.
Tom