Pro won't boot

[kwave]

After my reboot today my pro won't come up anymore. Maybe there was something changed by the last pacman update which prevents it from booting.

$this->bbcode_second_pass_code('', '[ 0.800000] Switched to NOHz mode on CPU #1
[ 0.810000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.820000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.820000] TCP reno registered
[ 0.830000] NET: Registered protocol family 1
[ 0.830000] Create fragment cache
[ 0.860000] fuse init (API version 7.12)
[ 0.860000] msgmni has been set to 244
[ 0.870000] alg: No test for stdrng (krng)
[ 0.870000] io scheduler noop registered
[ 0.870000] io scheduler anticipatory registered
[ 0.880000] io scheduler deadline registered
[ 0.880000] io scheduler cfq registered (default)
[ 0.910000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.920000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[ 0.930000] brd: module loaded
[ 0.940000] loop: module loaded
[ 0.950000] ox820sata: OX820 sata core.
[ 0.950000] scsi0 : oxnassata
[ 0.960000] scsi1 : oxnassata
[ 0.960000] ata1: SATA max UDMA/133 irq 50
[ 0.960000] ata2: SATA max UDMA/133 irq 50
[ 0.970000] ox820sata: reseting SATA core
[ 1.330000] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.330000] ox820sata: reseting SATA core
[ 1.690000] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.690000] tun: Universal TUN/TAP device driver, 1.6
[ 1.700000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.700000] NAND: Page read time 40ms
[ 1.710000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 1.720000] Scanning device for bad blocks
[ 1.790000] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
[ 1.800000] 0x000000000000-0x000000e00000 : "boot"
[ 1.800000] 0x000000e00000-0x000008000000 : "rootfs"
[ 1.810000] UBI: attaching mtd2 to ubi0
[ 1.810000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 1.820000] UBI: logical eraseblock size: 129024 bytes
[ 1.830000] UBI: smallest flash I/O unit: 2048
[ 1.830000] UBI: sub-page size: 512
[ 1.830000] UBI: VID header offset: 512 (aligned 512)
[ 1.840000] UBI: data offset: 2048
[ 2.250000] UBI: attached mtd2 to ubi0
[ 2.250000] UBI: MTD device name: "rootfs"
[ 2.260000] UBI: MTD device size: 114 MiB
[ 2.260000] UBI: number of good PEBs: 912
[ 2.270000] UBI: number of bad PEBs: 0
[ 2.270000] UBI: max. allowed volumes: 128
[ 2.280000] UBI: wear-leveling threshold: 4096
[ 2.280000] UBI: number of internal volumes: 1
[ 2.290000] UBI: number of user volumes: 1
[ 2.290000] UBI: available PEBs: 0
[ 2.290000] UBI: total number of reserved PEBs: 912
[ 2.300000] UBI: number of PEBs reserved for bad PEB handling: 9
[ 2.310000] UBI: max/mean erase counter: 2/0
[ 2.310000] UBI: image sequence number: 0
[ 2.310000] UBI: background thread "ubi_bgt0d" started, PID 306
[ 2.310000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.310000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
[ 2.310000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
[ 2.350000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
[ 2.370000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
[ 2.370000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.380000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.390000] usb usb1: Product: OXNAS EHCI Host Controller
[ 2.390000] usb usb1: Manufacturer: Linux 2.6.31.6_SMP_820 ehci_hcd
[ 2.400000] usb usb1: SerialNumber: usb
[ 2.400000] usb usb1: configuration #1 chosen from 1 choice
[ 2.410000] hub 1-0:1.0: USB hub found
[ 2.410000] hub 1-0:1.0: 2 ports detected
[ 2.420000] Initializing USB Mass Storage driver...
[ 2.420000] usbcore: registered new interface driver usb-storage
[ 2.430000] USB Mass Storage support registered.
[ 2.430000] usbcore: registered new interface driver libusual
[ 2.440000] usbcore: registered new interface driver ums-cypress
[ 2.440000] usbcore: registered new interface driver ums-datafab
[ 2.450000] usbcore: registered new interface driver ums-freecom
[ 2.460000] usbcore: registered new interface driver ums-isd200
[ 2.460000] usbcore: registered new interface driver ums-jumpshot
[ 2.470000] usbcore: registered new interface driver ums-sddr09
[ 2.470000] usbcore: registered new interface driver ums-sddr55
[ 2.480000] usbcore: registered new interface driver ums-usbat
[ 2.490000] mice: PS/2 mouse device common for all mice
[ 2.490000] usbcore: registered new interface driver hiddev
[ 2.500000] usbcore: registered new interface driver usbhid
[ 2.510000] usbhid: v2.6:USB HID core driver
[ 2.510000] TCP cubic registered
[ 2.510000] NET: Registered protocol family 10
[ 2.520000] lo: Disabled Privacy Extensions
[ 2.520000] NET: Registered protocol family 17
[ 2.530000] RPC: Registered udp transport module.
[ 2.530000] RPC: Registered tcp transport module.
[ 2.540000] Waiting 15sec before mounting root device...
[ 2.750000] usb 1-1: new high speed USB device using oxnas-ehci and address 2
[ 2.900000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 2.900000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 2.910000] usb 1-1: Product: USB2.0 Hub
[ 2.920000] usb 1-1: configuration #1 chosen from 1 choice
[ 2.920000] hub 1-1:1.0: USB hub found
[ 2.930000] hub 1-1:1.0: 4 ports detected
[ 3.210000] usb 1-1.3: new high speed USB device using oxnas-ehci and address 3
[ 6.360000] usb 1-1.3: New USB device found, idVendor=152d, idProduct=2509
[ 6.360000] usb 1-1.3: New USB device strings: Mfr=10, Product=11, SerialNumber=3
[ 6.370000] usb 1-1.3: Product: Usb production
[ 6.380000] usb 1-1.3: Manufacturer: Jmicron Corp.
[ 6.380000] usb 1-1.3: SerialNumber: 00A123456789
[ 6.390000] usb 1-1.3: configuration #1 chosen from 1 choice
[ 6.390000] scsi2 : SCSI emulation for USB Mass Storage devices
[ 11.680000] scsi 2:0:0:0: Direct-Access ST916082 3AS 0000 PQ: 0 ANSI: 2 CCS
[ 11.700000] sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 11.700000] sd 2:0:0:0: [sda] Write Protect is off
[ 11.710000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 11.720000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 11.720000] sda: sda1 sda2
[ 11.760000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 11.760000] sd 2:0:0:0: [sda] Attached SCSI disk
[ 17.600000] kjournald starting. Commit interval 5 seconds
[ 17.600000] EXT3 FS on sda1, internal journal
[ 17.600000] EXT3-fs: recovery complete.
[ 17.600000] EXT3-fs: mounted filesystem with writeback data mode.
[ 17.600000] VFS: Mounted root (ext3 filesystem) on device 8:1.
[ 17.630000] devtmpfs: mounted
[ 17.630000] Freeing init memory: 140K

INIT: version 2.88 booting

kill: usage: kill [-s sigspec | -n signum | -sigspec] pid | jobspec ... or kill -l [sigspec]

> Arch Linux ARM

> http://www.archlinuxarm.org

------------------------------
[ 20.430000] <30>systemd-udevd[361]: starting version 196
:: Mounting Root Read-Only .[s.[71G [BUSY] .[71G [FAIL]
:: Adjusting system time and setting kernel timezone .[s.[71G [BUSY] .[71G [DONE]
:: Starting UDev Daemon .[s.[71G [BUSY] .[71G [FAIL]
:: Triggering UDev uevents .[s.[71G [BUSY] .[71G [DONE]
:: Loading User-specified Modules .[s.[71G [BUSY] [ 21.580000] Probing for Synopsis GMAC, unit 0
[ 21.590000] eth0: Tuning GMAC 0 RGMII timings
[ 21.600000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
[ 21.600000] eth0: GMAC ver = 53, vendor ver = 18 at 0xed400000, IRQ 40
[ 21.610000] eth0: Found PHY at address 3, type 0x001cc914 -> 10/100/1000
[ 21.620000] eth0: Ethernet addr: 00:30:e0:00:00:00
[ 21.620000] probe() eth0: Leon x2 clock
.[71G [FAIL]
:: Waiting for UDev uevents to be processed .[s.[71G [BUSY] .[71G [DONE]
:: Bringing up loopback interface .[s.[71G [BUSY] .[71G [DONE]
:: Checking Filesystems .[s.[71G [BUSY] .[71G [DONE]
:: Remounting Root .[s.[71G [BUSY] .[71G [DONE]
:: Mounting Local Filesystems .[s.[71G [BUSY] [ 22.500000] kjournald starting. Commit interval 5 seconds
[ 22.510000] EXT3 FS on sda2, internal journal
[ 22.520000] EXT3-fs: recovery complete.
[ 22.520000] EXT3-fs: mounted filesystem with writeback data mode.
.[71G [DONE]
:: Activating Swap .[s.[71G [BUSY] [ 23.700000] Adding 524280k swap on /swapfile.img. Priority:-1 extents:136 across:711204k
.[71G [DONE]
:: Configuring Time Zone .[s.[71G [BUSY] .[71G [DONE]
:: Initializing Random Seed .[s.[71G [BUSY] .[71G [DONE]
:: Removing Leftover Files .[s.[71G [BUSY] /etc/rc.d/functions: line 509: /usr/lib/initscripts/arch-tmpfiles: No such file or directory
.[71G [FAIL]
:: Setting Hostname: plug .[s.[71G [BUSY] .[71G [DONE]
:: Setting Consoles to UTF-8 mode .[s.[71G [BUSY] .[71G [DONE]
:: Loading Keyboard Map: us .[s.[71G [BUSY] .[71G [DONE]
:: Saving dmesg Log .[s.[71G [BUSY] .[71G [DONE]

INIT: Entering runlevel: 3

[ 26.230000] <30>systemd-udevd[841]: starting version 196
[ 27.460000] <30>systemd-udevd[851]: starting version 196
:: Setting MAC address .[s.[71G [BUSY] [ 27.620000] Turning off blinking LED.
AMBER
GREEN
[ 27.840000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
[ 27.840000] CoPro offload is active on eth0
[ 27.850000] Alloc'ing ARM descs 8192 bytes
[ 27.850000] Alloc'ing CoPro parameters 36 bytes
[ 27.860000] gmac gmac.0: firmware: requesting gmac_copro_firmware
[ 27.930000] open() eth0: Failed to load CoPro firmware')

Seems like it doesn't mount the root fs anymore. right? I googled a lot and found this https://github.com/archlinuxarm/PKGBUILDs/issues/211 post. In my sysinit this issue is fixed already.

So how to fix this?

[dinjo]

i did a update last night and rebooted I'll check today whether its ok or not