i had trouble when updating to the new oxnas kernel.
I described the problem here with 4 postings: viewtopic.php?f=29&t=2453&start=100#p28205
At first i installed on my Pogoplug Pro (which is as far as i understand a PCI device) the NOPCI kernel into NAND.
After reboot the system died on bootup.
After manually fixing the symlink to /lib/ the system booted again.
But wifi does not work - as far as i understand in fact that i patched the wrong kernel.
So i patched the NAND manually by executing:
$this->bbcode_second_pass_code('', '
#: flash_erase /dev/mtd1 0x500000 20
Erasing 128 Kibyte @ 760000 -- 100 % complete
#: nandwrite -p -s 0x500000 /dev/mtd1 boot/uImage.pci
Writing data to block 40 at offset 0x500000
Writing data to block 41 at offset 0x520000
Writing data to block 42 at offset 0x540000
Writing data to block 43 at offset 0x560000
Writing data to block 44 at offset 0x580000
Writing data to block 45 at offset 0x5a0000
Writing data to block 46 at offset 0x5c0000
Writing data to block 47 at offset 0x5e0000
Writing data to block 48 at offset 0x600000
Writing data to block 49 at offset 0x620000
Writing data to block 50 at offset 0x640000
Writing data to block 51 at offset 0x660000
Writing data to block 52 at offset 0x680000
Writing data to block 53 at offset 0x6a0000
Writing data to block 54 at offset 0x6c0000
Writing data to block 55 at offset 0x6e0000
Writing data to block 56 at offset 0x700000
Writing data to block 57 at offset 0x720000
')
But: after rebooting network does not respond.
I created a second usb stick with a new blank filesystem "Help - it stopped working" on the pogoplug archlinux installation page (http://archlinuxarm.org/platforms/armv6 ... provideov3) recommends.
This stick works, but i want to get the old stick working again. The old system runs for over two years nearly without problems
and i dont want to reinstall all services.
So i fetched the DMESG log files from /var/log for both sticks and diffed them.
As far as i understand there are no bigger problems, but there are some differences.
Here the DMESG log of the OLD usb drive i want to get working again
$this->bbcode_second_pass_code('', '
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125240KB available (3904K code, 303K data, 140K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:96
OX820_RPS_init_irq: interrupts 64 to 96
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Calibrating local timer... 350.00MHz.
CPU1: Booted secondary processor
Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
Brought up 2 CPUs
SMP: Total of 2 processors activated (558.69 BogoMIPS).
tmpfs: No value for mount option 'mode'
devtmpfs: initialized
NET: Registered protocol family 16
Number of DMA channels = 4, version = 4
Reserving a DMA channel for DirectRAID
Allocating 389 SRAM generic DMA descriptors
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Switched to NOHz mode on CPU #0
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Switched to NOHz mode on CPU #1
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
Create fragment cache
fuse init (API version 7.12)
msgmni has been set to 244
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
brd: module loaded
loop: module loaded
ox820sata: OX820 sata core.
scsi0 : oxnassata
scsi1 : oxnassata
ata1: SATA max UDMA/133 irq 50
ata2: SATA max UDMA/133 irq 50
ox820sata: reseting SATA core
ata1: SATA link down (SStatus 0 SControl 300)
ox820sata: reseting SATA core
ata2: SATA link down (SStatus 0 SControl 300)
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
NAND: Page read time 40ms
NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 125 at 0x000000fa0000
Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x000000000000-0x000000e00000 : "boot"
0x000000e00000-0x000008000000 : "rootfs"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd2 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 114 MiB
UBI: number of good PEBs: 911
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 911
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 2/1
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 306
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96
<6>probe for usb
<6>starting usb for 820
ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96
<6>initialise for OX820 series USB
<6>usb hsmph ctrl set to:0x425435e0
<6>registers:
<6>SYS_CTRL_CKEN_CTRL 0xf1e00024: 0x00000000
<6>SYS_CTRL_RSTEN_CTRL 0xf1e00028: 0x00000000
<6>SYS_CTRL_USBHSPHY_CTRL 0xf1e00084: 0x00002abd
<6>SYS_CTRL_TERTIARY_SEL 0xf1e0008c: 0x00000000
<6>SYS_CTRL_SECONDARY_SEL 0xf1e00014: 0x01fff018
<6>SYS_CTRL_REF300_DIV 0xf1e000f8: 0x00001900
<6>SYS_CTRL_USB_CTRL 0xf1e00090: 0x00000042
<6>@ed200000 Device ID register 42fa05
oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
oxnas-ehci oxnas-ehci.0: reset
hcs_params 0x1210012 dbg=2 ind cc=0 pcc=0 ordered ports=2
oxnas-ehci oxnas-ehci.0: reset
hcc_params 0006 thresh 0 uframes 256/512/1024 park
oxnas-ehci oxnas-ehci.0: park 0
oxnas-ehci oxnas-ehci.0: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
oxnas-ehci oxnas-ehci.0: ...powerdown ports...
oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
oxnas-ehci oxnas-ehci.0: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
oxnas-ehci oxnas-ehci.0: init command 010009 (park)=0 ithresh=1 period=256 RUN
oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OXNAS EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31.6_SMP_820 ehci_hcd
usb usb1: SerialNumber: usb
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: individual port power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
drivers/usb/core/inode.c: creating file '001'
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Waiting 15sec before mounting root device...
oxnas-ehci oxnas-ehci.0: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 1: status 0101 change 0001
hub 1-0:1.0: state 7 ports 2 chg 0002 evt 0000
hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 1-1: new high speed USB device using oxnas-ehci and address 2
oxnas-ehci oxnas-ehci.0: port 1 high speed
oxnas-ehci oxnas-ehci.0: GetStatus port 1 status 8001205 POWER sig=se0 PE CONNECT
usb 1-1: default language 0x0409
usb 1-1: udev 2, busnum 1, minor = 1
usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: Product: USB2.0 Hub
usb 1-1: uevent
usb 1-1: usb_probe_device
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: uevent
hub 1-1:1.0: usb_probe_interface
hub 1-1:1.0: usb_probe_interface - got id
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hub 1-1:1.0: standalone hub
hub 1-1:1.0: ganged power switching
hub 1-1:1.0: global over-current protection
hub 1-1:1.0: Single TT
hub 1-1:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 1-1:1.0: Port indicators are supported
hub 1-1:1.0: power on to power good time: 100ms
hub 1-1:1.0: local power source is good
hub 1-1:1.0: no over-current condition exists
hub 1-1:1.0: enabling power on all ports
drivers/usb/core/inode.c: creating file '002'
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
hub 1-1:1.0: port 4: status 0101 change 0001
usb 1-1: link qh256-0001/ffc00100 start 1 [1/0 us]
hub 1-1:1.0: state 7 ports 4 chg 0010 evt 0000
hub 1-1:1.0: port 4, status 0101, change 0000, 12 Mb/s
usb 1-1.4: new high speed USB device using oxnas-ehci and address 3
usb 1-1.4: default language 0x0409
usb 1-1.4: udev 3, busnum 1, minor = 2
usb 1-1.4: New USB device found, idVendor=0781, idProduct=5205
usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.4: Product: Extreme Ducati
usb 1-1.4: Manufacturer: SanDisk Corporation
usb 1-1.4: SerialNumber: 200517415214377194CA
usb 1-1.4: uevent
usb 1-1.4: usb_probe_device
usb 1-1.4: configuration #1 chosen from 1 choice
usb 1-1.4: adding 1-1.4:1.0 (config #1, interface 0)
usb 1-1.4:1.0: uevent
usb-storage 1-1.4:1.0: usb_probe_interface
usb-storage 1-1.4:1.0: usb_probe_interface - got id
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
drivers/usb/core/inode.c: creating file '003'
hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0010
scsi 2:0:0:0: Direct-Access SanDisk Extreme Ducati 0.1 PQ: 0 ANSI: 2
usb-storage: device scan complete
sd 2:0:0:0: [sda] 8027712 512-byte logical blocks: (4.11 GB/3.82 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] Attached SCSI removable disk
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) on device 8:1.
devtmpfs: mounted
Freeing init memory: 140K
NET: Registered protocol family 3
NET: Registered protocol family 6
NET: Registered protocol family 11
NET: Registered protocol family 4
NET: Registered protocol family 5
<30>udevd[449]: starting version 175
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-1: uevent
usb 1-1.4: uevent
usb 1-1.4:1.0: uevent
usb 1-1:1.0: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-1: uevent
usb 1-1.4: uevent
usb 1-1.4:1.0: uevent
usb 1-1.4:1.0: uevent
usb 1-1.4: uevent
usb 1-1:1.0: uevent
Probing for Synopsis GMAC, unit 0
eth0: Tuning GMAC 0 RGMII timings
eth0: PHY is Realtek RTL8211D, type 0x001cc914
eth0: GMAC ver = 53, vendor ver = 18 at 0xed400000, IRQ 40
eth0: Found PHY at address 3, type 0x001cc914 -> 10/100/1000
eth0: Ethernet addr: 00:30:e0:00:00:00
probe() eth0: Leon x2 clock
rt3390sta: Unknown symbol pci_enable_device
rt3390sta: Unknown symbol __pci_register_driver
rt3390sta: Unknown symbol pci_request_regions
rt3390sta: Unknown symbol pci_unregister_driver
rt3390sta: Unknown symbol pci_bus_read_config_word
rt3390sta: Unknown symbol pci_find_capability
rt3390sta: Unknown symbol pci_set_master
rt3390sta: Unknown symbol pci_bus_write_config_word
rt3390sta: Unknown symbol pci_release_regions
rt3390sta: Unknown symbol pci_disable_device
rt3390sta: Unknown symbol pci_get_slot
rt3390sta: Unknown symbol pci_bus_read_config_byte
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
Adding 524280k swap on /swapfile. Priority:-1 extents:351 across:945864k
')
And here the DMESG log of the new usb drive i created with the new file system:
$this->bbcode_second_pass_code('', '
Brought up 2 CPUs
SMP: Total of 2 processors activated (558.69 BogoMIPS).
tmpfs: No value for mount option 'mode'
devtmpfs: initialized
NET: Registered protocol family 16
Number of DMA channels = 4, version = 4
Reserving a DMA channel for DirectRAID
Allocating 389 SRAM generic DMA descriptors
PCIeA version/deviceID 082510b5
PCIeB version/deviceID 082510b5
ox820_pci_preinit() PCIEB link up timeout (00001814)
ox820_pcie_setup_resources() Enabling PCIe Pre-Emphasis
ox820_pciea_setup_resources() resource c781b140
ox820_pciea_setup_resources() io: 0x4be00000 - 0x4befffff
ox820_pciea_setup_resources() non-pre: 0x48000000 - 0x49ffffff
ox820_pciea_setup_resources() pre: 0x4a000000 - 0x4bdfffff
pci 0000:00:00.0: reg 10 32bit mmio: [0x000000-0x00ffff]
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Switched to NOHz mode on CPU #0
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Switched to NOHz mode on CPU #1
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
Create fragment cache
fuse init (API version 7.12)
msgmni has been set to 244
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
brd: module loaded
loop: module loaded
ox820sata: OX820 sata core.
scsi0 : oxnassata
scsi1 : oxnassata
ata1: SATA max UDMA/133 irq 50
ata2: SATA max UDMA/133 irq 50
ox820sata: reseting SATA core
ata1: SATA link down (SStatus 0 SControl 300)
ox820sata: reseting SATA core
ata2: SATA link down (SStatus 0 SControl 300)
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
NAND: Page read time 40ms
NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 125 at 0x000000fa0000
Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x000000000000-0x000000e00000 : "boot"
0x000000e00000-0x000008000000 : "rootfs"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd2 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 114 MiB
UBI: number of good PEBs: 911
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 911
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 2/1
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 313
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96
<6>probe for usb
<6>starting usb for 820
ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96
<6>initialise for OX820 series USB
<6>usb hsmph ctrl set to:0x2a5435e0
<6>registers:
<6>SYS_CTRL_CKEN_CTRL 0xf1e00024: 0x00000000
<6>SYS_CTRL_RSTEN_CTRL 0xf1e00028: 0x00000000
<6>SYS_CTRL_USBHSPHY_CTRL 0xf1e00084: 0x00002abd
<6>SYS_CTRL_TERTIARY_SEL 0xf1e0008c: 0x00000000
<6>SYS_CTRL_SECONDARY_SEL 0xf1e00014: 0x01fff018
<6>SYS_CTRL_REF300_DIV 0xf1e000f8: 0x00001900
<6>SYS_CTRL_USB_CTRL 0xf1e00090: 0x00000042
<6>@ed200000 Device ID register 42fa05
oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
oxnas-ehci oxnas-ehci.0: reset
hcs_params 0x1210012 dbg=2 ind cc=0 pcc=0 ordered ports=2
oxnas-ehci oxnas-ehci.0: reset
hcc_params 0006 thresh 0 uframes 256/512/1024 park
oxnas-ehci oxnas-ehci.0: park 0
oxnas-ehci oxnas-ehci.0: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
oxnas-ehci oxnas-ehci.0: ...powerdown ports...
oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
oxnas-ehci oxnas-ehci.0: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
oxnas-ehci oxnas-ehci.0: init command 010009 (park)=0 ithresh=1 period=256 RUN
oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OXNAS EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31.6_SMP_820 ehci_hcd
usb usb1: SerialNumber: usb
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: individual port power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
drivers/usb/core/inode.c: creating file '001'
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Waiting 15sec before mounting root device...
oxnas-ehci oxnas-ehci.0: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 1: status 0101 change 0001
hub 1-0:1.0: state 7 ports 2 chg 0002 evt 0000
hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 1-1: new high speed USB device using oxnas-ehci and address 2
oxnas-ehci oxnas-ehci.0: port 1 high speed
oxnas-ehci oxnas-ehci.0: GetStatus port 1 status 8001205 POWER sig=se0 PE CONNECT
usb 1-1: default language 0x0409
usb 1-1: udev 2, busnum 1, minor = 1
usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: Product: USB2.0 Hub
usb 1-1: uevent
usb 1-1: usb_probe_device
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: uevent
hub 1-1:1.0: usb_probe_interface
hub 1-1:1.0: usb_probe_interface - got id
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hub 1-1:1.0: standalone hub
hub 1-1:1.0: ganged power switching
hub 1-1:1.0: global over-current protection
hub 1-1:1.0: Single TT
hub 1-1:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 1-1:1.0: Port indicators are supported
hub 1-1:1.0: power on to power good time: 100ms
hub 1-1:1.0: local power source is good
hub 1-1:1.0: no over-current condition exists
hub 1-1:1.0: enabling power on all ports
drivers/usb/core/inode.c: creating file '002'
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
hub 1-1:1.0: port 4: status 0101 change 0001
usb 1-1: link qh256-0001/ffc00100 start 1 [1/0 us]
hub 1-1:1.0: state 7 ports 4 chg 0010 evt 0000
hub 1-1:1.0: port 4, status 0101, change 0000, 12 Mb/s
usb 1-1.4: new high speed USB device using oxnas-ehci and address 3
usb 1-1.4: default language 0x0409
usb 1-1.4: udev 3, busnum 1, minor = 2
usb 1-1.4: New USB device found, idVendor=090c, idProduct=1000
usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.4: SerialNumber: 12071685012151
usb 1-1.4: uevent
usb 1-1.4: usb_probe_device
usb 1-1.4: configuration #1 chosen from 1 choice
usb 1-1.4: adding 1-1.4:1.0 (config #1, interface 0)
usb 1-1.4:1.0: uevent
usb-storage 1-1.4:1.0: usb_probe_interface
usb-storage 1-1.4:1.0: usb_probe_interface - got id
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
drivers/usb/core/inode.c: creating file '003'
hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0010
scsi 2:0:0:0: Direct-Access PQ: 0 ANSI: 4
usb-storage: device scan complete
sd 2:0:0:0: [sda] 62259200 512-byte logical blocks: (31.8 GB/29.6 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] Attached SCSI removable disk
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) on device 8:1.
devtmpfs: mounted
Freeing init memory: 144K
NET: Registered protocol family 3
NET: Registered protocol family 6
NET: Registered protocol family 11
NET: Registered protocol family 4
NET: Registered protocol family 5
<30>systemd-udevd[505]: starting version 196
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-1: uevent
usb 1-1.4: uevent
usb 1-1.4:1.0: uevent
usb 1-1:1.0: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-1: uevent
usb usb1: uevent
usb usb1: uevent
usb usb1: uevent
usb 1-1.4: uevent
usb 1-1:1.0: uevent
usb 1-1: uevent
usb 1-1: uevent
usb 1-1: uevent
usb 1-1.4:1.0: uevent
usb 1-1.4: uevent
usb 1-1.4: uevent
usb 1-1.4:1.0: uevent
usb 1-1.4:1.0: uevent
usb 1-1.4: uevent
Probing for Synopsis GMAC, unit 0
eth0: Tuning GMAC 0 RGMII timings
eth0: PHY is Realtek RTL8211D, type 0x001cc914
eth0: GMAC ver = 53, vendor ver = 18 at 0xed400000, IRQ 40
eth0: Found PHY at address 3, type 0x001cc914 -> 10/100/1000
eth0: Ethernet addr: 00:30:e0:00:00:00
probe() eth0: Leon x2 clock
EXT3 FS on sda1, internal journal
Turning off blinking LED.
eth0: PHY is Realtek RTL8211D, type 0x001cc914
CoPro offload is active on eth0
Alloc'ing ARM descs 8192 bytes
Alloc'ing CoPro parameters 36 bytes
gmac gmac.0: firmware: requesting gmac_copro_firmware
CoPro: Programming start address as 0xd000e000
eth0: Resetting GMAC
eth0: GMAC reset complete
eth0: Setting Rx flow control thresholds for LAN port
eth0: PHY is Realtek RTL8211D, type 0x001cc914
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
eth0: link up, 100Mbps, full-duplex, using pause, lpa 0x45E1
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
')
I recommend to copy both logs into a diff program like meld (linux) or winmerge (windows) to see the differences.
Do you have some ideas what i made wrong?
Thank you in advance, i am sure, it can be recovered
