[SOLVED] Pogoplug V4 won't boot after install

[senselessfull]

So I bought a pogoplug v4-a3-01 and the first thing I did was to install arch.
I followed the instructions provided here but it didn't boot.

So serial cable and this it what happens:
$this->bbcode_second_pass_code('', '


U-Boot 1.1.4 (Oct 1 2011 - 12:06:06) Cloud Engines 1.1.2 (3.4.27) PHYADDR=0

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006918B4

Soc: 88F6192 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV4A3

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 1  0
Unknown command 'usb' - try 'help'

NAND read: device 0 offset 0x100000, size 0x73d0c
474380 bytes read: OK
## Starting application at 0x00800000 ...


U-Boot 1.1.4 (Jan 13 2012 - 22:33:21) Arch Linux ARM (PPV4 r1) PHYADDR=0

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFD60

Soc: 88F6192 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV4A3

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 1  0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found

No Fat FS detected

IDE device 0 not available
....
.......................................................................................................................................................................................................................................................................................................................................................................................................

4054464 bytes read
## Booting image at 00800000 ...
Image Name: Linux-3.19.0-1-ARCH
Created: 2015-02-10 4:56:00 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4054400 Bytes = 3.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.19.0-1-ARCH (builduser@leming) (gcc version 4.9.2 20141224 (prerelease) (GCC) ) #1 PREEMPT Mon Feb 9 21:55:44 MST 2015
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Pogoplug V4
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootwait rootfstype=ext3
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 120980K/131072K available (5722K kernel code, 354K rwdata, 1720K rodata, 268K init, 698K bss, 10092K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc074ccd4 (7444 kB)
[ 0.000000] .init : 0xc074d000 - 0xc0790000 ( 268 kB)
[ 0.000000] .data : 0xc0790000 - 0xc07e88bc ( 355 kB)
[ 0.000000] .bss : 0xc07e88bc - 0xc08972b8 ( 699 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:114
[ 0.000017] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 25769803770ns
[ 11.845075] Console: colour dummy device 80x30
[ 11.845115] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[ 11.934902] pid_max: default: 32768 minimum: 301
[ 11.935044] Security Framework initialized
[ 11.935154] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 11.935181] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 11.936208] Initializing cgroup subsys memory
[ 11.936273] Initializing cgroup subsys devices
[ 11.936309] Initializing cgroup subsys freezer
[ 11.936338] Initializing cgroup subsys net_cls
[ 11.936366] Initializing cgroup subsys blkio
[ 11.936392] Initializing cgroup subsys bfqio
[ 11.936419] Initializing cgroup subsys perf_event
[ 11.936447] Initializing cgroup subsys net_prio
[ 11.936580] CPU: Testing write buffer coherency: ok
[ 11.937209] Setting up static identity map for 0x5741d0 - 0x574228
[ 11.939968] devtmpfs: initialized
[ 11.944038] pinctrl core: initialized pinctrl subsystem
[ 11.945092] NET: Registered protocol family 16
[ 11.945790] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 11.974935] cpuidle: using governor ladder
[ 12.004929] cpuidle: using governor menu
[ 12.005126] Kirkwood: MV88F6281-A1, TCLK=166666667.
[ 12.005159] Feroceon L2: Enabling L2
[ 12.005211] Feroceon L2: Cache support initialised.
[ 12.008512] Kirkwood PCIe port 0: link up
[ 12.008527] PCI: bus0 uses PCIe port 0
[ 12.008870] PCI host bridge to bus 0000:00
[ 12.008896] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 12.008914] pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
[ 12.008929] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 12.010030] PCI: bus0: Fast back to back transfers disabled
[ 12.010103] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[ 12.010136] pci 0000:00:01.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[ 12.010166] pci 0000:00:01.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[ 12.047288] vgaarb: loaded
[ 12.047773] SCSI subsystem initialized
[ 12.048504] usbcore: registered new interface driver usbfs
[ 12.048616] usbcore: registered new interface driver hub
[ 12.048704] usbcore: registered new device driver usb
[ 12.048941] pps_core: LinuxPPS API ver. 1 registered
[ 12.048955] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 12.049006] PTP clock support registered
[ 12.050578] Switched to clocksource orion_clocksource
[ 12.077300] FS-Cache: Loaded
[ 12.096036] NET: Registered protocol family 2
[ 12.097285] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 12.097322] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 12.097351] TCP: Hash tables configured (established 1024 bind 1024)
[ 12.097450] TCP: reno registered
[ 12.097469] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 12.097501] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 12.097771] NET: Registered protocol family 1
[ 12.100354] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 12.118985] VFS: Disk quotas dquot_6.5.2
[ 12.119382] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 12.122340] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 12.123905] fuse init (API version 7.23)
[ 12.127252] aufs 3.x-rcN-20150126
[ 12.130196] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 12.130227] io scheduler noop registered
[ 12.130246] io scheduler deadline registered
[ 12.130713] io scheduler cfq registered
[ 12.131386] io scheduler bfq registered (default)
[ 12.131399] BFQ I/O-scheduler version: v7r7
[ 12.131716] mv_xor mv_xor.0: Marvell shared XOR driver
[ 12.170708] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 12.210689] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 12.210957] mv_xor mv_xor.1: Marvell shared XOR driver
[ 12.250670] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 12.290669] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 12.298598] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 12.300173] console [ttyS0] disabled
[ 12.320260] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[ 12.876406] console [ttyS0] enabled
[ 12.893784] brd: module loaded
[ 12.903456] loop: module loaded
[ 12.907115] sata_mv sata_mv.0: cannot get optional clkdev
[ 12.912626] sata_mv sata_mv.0: slots 32 ports 1
[ 12.919707] scsi host0: sata_mv
[ 12.923469] ata1: SATA max UDMA/133 irq 21
[ 12.928989] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 12.935512] nand: Hynix H27U1G8F2BTR-BC
[ 12.939340] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 12.946916] Scanning device for bad blocks
[ 13.016372] Creating 5 MTD partitions on "orion_nand":
[ 13.021585] 0x000000000000-0x000000200000 : "u-boot"
[ 13.027244] 0x000000200000-0x000000500000 : "uImage"
[ 13.032912] 0x000000500000-0x000000800000 : "uImage2"
[ 13.038586] 0x000000800000-0x000001000000 : "failsafe"
[ 13.044383] 0x000001000000-0x000008000000 : "root"
[ 13.058934] libphy: orion_mdio_bus: probed
[ 13.063227] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 13.280616] ata1: SATA link down (SStatus 0 SControl F300)
[ 14.144932] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:2c:10
[ 14.153993] xhci_hcd 0000:00:01.0: xHCI Host Controller
[ 14.159236] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 1
[ 14.169332] hub 1-0:1.0: USB hub found
[ 14.173187] hub 1-0:1.0: 2 ports detected
[ 14.178073] xhci_hcd 0000:00:01.0: xHCI Host Controller
[ 14.183373] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[ 14.192120] hub 2-0:1.0: USB hub found
[ 14.195899] hub 2-0:1.0: 2 ports detected
[ 14.200983] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 14.207488] ehci-pci: EHCI PCI platform driver
[ 14.212077] ehci-orion: EHCI orion driver
[ 14.216183] orion-ehci orion-ehci.0: EHCI Host Controller
[ 14.221658] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 3
[ 14.229408] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 14.250625] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 14.257856] hub 3-0:1.0: USB hub found
[ 14.261702] hub 3-0:1.0: 1 port detected
[ 14.266525] usbcore: registered new interface driver uas
[ 14.272301] usbcore: registered new interface driver usb-storage
[ 14.278367] usbcore: registered new interface driver ums-alauda
[ 14.284409] usbcore: registered new interface driver ums-cypress
[ 14.290471] usbcore: registered new interface driver ums-datafab
[ 14.296787] usbcore: registered new interface driver ums_eneub6250
[ 14.303056] usbcore: registered new interface driver ums-freecom
[ 14.309114] usbcore: registered new interface driver ums-isd200
[ 14.315114] usbcore: registered new interface driver ums-jumpshot
[ 14.321288] usbcore: registered new interface driver ums-karma
[ 14.327172] usbcore: registered new interface driver ums-onetouch
[ 14.333380] usbcore: registered new interface driver ums-realtek
[ 14.339453] usbcore: registered new interface driver ums-sddr09
[ 14.345461] usbcore: registered new interface driver ums-sddr55
[ 14.351463] usbcore: registered new interface driver ums-usbat
[ 14.357914] mousedev: PS/2 mouse device common for all mice
[ 14.580655] usb 3-1: new high-speed USB device number 2 using orion-ehci
[ 14.732843] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 14.739333] scsi host1: usb-storage 3-1:1.0
[ 15.370622] rtc-mv rtc-mv: internal RTC not ticking
[ 15.375692] i2c /dev entries driver
[ 15.379869] Driver 'mmcblk' needs updating - please use bus_type methods
[ 15.386744] sdhci: Secure Digital Host Controller Interface driver
[ 15.392922] sdhci: Copyright(c) Pierre Ossman
[ 15.397362] mvsdio mvsdio: no pins associated
[ 15.440888] sdhci-pltfm: SDHCI platform and OF driver helper
[ 15.450403] ledtrig-cpu: registered to indicate activity on CPUs
[ 15.456661] usbcore: registered new interface driver r8712u
[ 15.462602] gre: GRE over IPv4 demultiplexor driver
[ 15.467546] TCP: cubic registered
[ 15.470944] NET: Registered protocol family 17
[ 15.475577] Key type dns_resolver registered
[ 15.482299] registered taskstats version 1
[ 15.488283] console [netcon0] enabled
[ 15.492039] netconsole: network logging started
[ 15.497192] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 15.504345] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 15.512448] Waiting for root device /dev/sda1...
[ 15.741697] scsi 1:0:0:0: Direct-Access SanDisk Cruzer Blade 1.20 PQ: 0 ANSI: 5
[ 15.751677] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 15.757233] sd 1:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 15.766334] sd 1:0:0:0: [sda] Write Protect is off
[ 15.771959] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 15.787444] sda: sda1
[ 15.793585] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 15.842226] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[ 15.871728] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 15.879439] VFS: Mounted root (ext3 filesystem) on device 8:1.
[ 15.889414] devtmpfs: mounted
[ 15.893729] Freeing unused kernel memory: 268K (c074d000 - c0790000)
[ 15.945048] Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[ 15.958127] CPU: 0 PID: 1 Comm: swapper Not tainted 3.19.0-1-ARCH #1
[ 15.964450] Hardware name: Pogoplug V4
[ 15.968221] [<c000f040>] (unwind_backtrace) from [<c000c594>] (show_stack+0x10/0x14)
[ 15.975942] [<c000c594>] (show_stack) from [<c056ab04>] (panic+0x88/0x1f8)
[ 15.982798] [<c056ab04>] (panic) from [<c056a1a0>] (kernel_init+0xc8/0xec)
[ 15.989647] [<c056a1a0>] (kernel_init) from [<c0009638>] (ret_from_fork+0x14/0x3c)
[ 15.997190] ---[ end Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
')
Do you have any idea to why that happens?
I checked and there is a init in /sbin/init and it points to systemd.

But that shouldn't be a problem, should it?
Any help is really appreciated.

[WarheadsSE]

Add to command line/bootargs:
$this->bbcode_second_pass_code('', 'init=/usr/lib/systemd/systemd')

This should at least get you booting. If that doesn't work, we've got some larger issues with your drive, apparently.

[senselessfull]

You want to have
$this->bbcode_second_pass_code('', '
optargs=init=/usb/lib/systemd/systemd
')

Though, that might be "extraargs"

EDIT:
um, who changed my reply instead of posting a new response?

[senselessfull]

I tried adding
optargs=init=/usr/lib/systemd/systemd
and
extraargs=init=/usr/lib/systemd/systemd

to /boot/uEnv.txt and nothing changed.

Where am I supposed to add those entries to?
EDIT:
So I added init=/usr/lib/systemd/systemd to my bootargs in the u-boot enivronment (and saved them) but it still panics at boot.

Also ls just return that the mtdids are not defined, should that be like that?

[WarheadsSE]

I am getting the feeling it doesn't like your USB stick's rootfs. It is that Cruzer, yes?

[senselessfull]

Yes, you guessed it exactly right. It one of those cruzer blades.

I'll try with another stick right now.

EDIT:
Yes, another edit. I know.
BUT, it works now with another USB stick, it's still from sandisk but not a cruzr. It's a Ultra 3.0.

By the way, the reinstallation tutorial calls for ext4 but that didn't work at all. Even tried ext2 but the onyl thing that worked was ext3. So we shoudl probably update that part.
Another noname stick also didn't work with ext4, so it might not just be connected to sandisk.

But thanks for the help