GoFlex NET wont boot, Unable to get to Marvell prompt!

[sissycockmilker]

Hi,
Used the ArchLinux Arm instructions from http://archlinuxarm.org/platforms/armv5 ... goflex-net the device ceased to boot. Got a good working rootfs of Wheezy and it is still not booting.

Serial console, output! (While loading hitting a key to abort booting, is not working) Pl. help!

Unable to get to Marvell prompt, hitting keys like crazy but does not stop from booting!

$this->bbcode_second_pass_code('', '


U-Boot 2010.09 (Feb 16 2011 - 18:42:02)
UBIT v0.6 by Jeff Doozan and Peter Carmichael

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:silent", error -19
Error reading superblock on volume 'ubi:silent'!
UBIFS not mounted, use ubifs mount to mount volume first!
Using egiga0 device
ping failed; host 10.10.10.5 is not alive
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Marvell>> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3> ing failed; hos3

')

[WarheadsSE]

Looks like you have gibberish on your serial line. Check tx and gnd.

[sissycockmilker]

Thank you for your reply, I did check, however it reads initially and the output is the same every time.
I will do some more checking/experimenting and post here.

Thank you.

[sissycockmilker]

OMG I feel so stupid wasting a whole day trying to figure it out. Thank you so much.
I reattached the serial console and it worked.

If anyone could please help me further. Below are the environment variables.

$this->bbcode_second_pass_code('', '


U-Boot 2010.09 (Feb 16 2011 - 18:42:02)
UBIT v0.6 by Jeff Doozan and Peter Carmichael

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:silent", error -19
Error reading superblock on volume 'ubi:silent'!
UBIFS not mounted, use ubifs mount to mount volume first!
Using egiga0 device
ping failed; host 10.10.10.5 is not alive
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
Marvell>> printenv
bootcmd=run fast_boot; run usb_boot; run hd_boot; run ubi_boot
bootdelay=3
baudrate=115200
ide_start=ide reset
ubi_start=ubi part root
usb_start=usb start
nc_test=ping $ncip
nc_start=setenv stdin nc; setenv stdout nc; setenv stderr nc; version
silent_boot=run silent_rd ubi_args ubi_fallback
fast_boot=run fast_rd ubi_args ubi_fallback
usb_boot=for scan in 0 1 2 3; do run usb_args_$scan ext2_kern ext2_boot; run ext2_rd ubi_fallback; run fat_kern fat_boot; run fat_rd ubi_fallback;done
usb_args_0=boot_dev='usb 0:1'; dev_args='root=/dev/sda1 rootdelay=10'
usb_args_1=boot_dev='usb 1:1'; dev_args='root=/dev/sdb1 rootdelay=10'
usb_args_2=boot_dev='usb 2:1'; dev_args='root=/dev/sdc1 rootdelay=10'
usb_args_3=boot_dev='usb 3:1'; dev_args='root=/dev/sdd1 rootdelay=10'
hd_boot=run ide_start; for scan in 0 1; do run hd_args_$scan ext2_kern ext2_boot; run ext2_rd ubi_fallback; run fat_kern fat_boot; run fat_rd ubi_fallback; done
hd_args_0=boot_dev='ide 0:1'; dev_args='root=/dev/sda1'
hd_args_1=boot_dev='ide 1:1'; dev_args='root=/dev/sdb1'
ubi_boot=run ubi_rd ubi_args ubi_fallback
ubi_args=dev_args='ubi.mtd=root'
rescue=dev_args='ubi.mtd=root rootfstype=preboot'; boot_dev='usb 0:1'; run ext2_kern ext2_auto boot_rd; boot_dev='ide 0:1'; run ide_start ext2_kern ext2_auto boot_rd; run silent_rd ubi_fallback; run fast_rd ubi_fallback; run ubi_rd ubi_fallback
chain=nand read.e 0x800000 0x480000 0x80000; go 0x800200
ethact=egiga0
console=ttyS0,115200
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(pogoplug),-(root)
set_bootargs=setenv bootargs console=$console $mtdparts $dev_args $rd_args netconsole=@$ipaddr/eth0,@$ncipk/
ext2_kern=ext2load $boot_dev $addr_kern /boot/uImage
ext2_auto=ext2load $boot_dev $addr_rd /boot/uInitrd
ext2_rd=ext2load $boot_dev $addr_rd /uInitrd
ext2_boot=run ext2_rd boot_rd; run ext2_auto boot_auto; run boot_kern
fat_kern=fatload $boot_dev $addr_kern /boot/uImage
fat_rd=fatload $boot_dev $addr_rd /uInitrd
fat_boot=run fat_rd boot_rd
ubi_kern=ubifsmount boot; ubifsload $addr_kern /boot/uImage
ubi_rd=ubifsmount ramdisk; ubifsload $addr_rd /uInitrd
ubi_fallback=run ubi_kern boot_rd
silent_rd=ubifsmount silent; ubifsload $addr_rd /uInitrd
fast_rd=ubifsmount fast; ubifsload $addr_rd /uInitrd
boot_kern=run set_bootargs; bootm $addr_kern
boot_rd=run set_bootargs; bootm $addr_kern $addr_rd
boot_auto=rd_args='rootfstype=auto'; run boot_rd
addr_kern=0x680000
addr_rd=0x1100000
ipaddr=10.10.10.6
ncip=10.10.10.5
ncipk=10.10.10.4
serverip=10.10.10.3
led_init=green blinking
led_exit=green off
led_error=orange blinking
ethaddr=02:50:43:ca:c7:a0
preboot=run ubi_start silent_boot; run nc_test nc_start; run usb_start
stdin=serial
stdout=serial
stderr=serial
partition=nand0,0
mtddevnum=0
mtddevname=u-boot

Environment size: 2768/131068 bytes
Marvell>>

')

[sissycockmilker]

Got it all sorted!
Thank you, am able to SSH now.


*Hug*