Hi,
This is my first time in Arch-Linux. But I am not new to Linux platform as I am using Ubuntu servers since 2016 and I new few beginner stuff. Due to lock-down I was bored, So I look around in my store to find something that i can work on and I found an old but working ix2-200. It was 2 Slot NAS but i used it 1 Hard drive for my Ubuntu server. So it was left with 1 drive with its firmware and due to no use for like 5-6 years that only drive also died and i was left with broken NAS ix2-200. After a lot of Googling i was unable to install its original firmware and i reset its SETENV values to default. And After that i stumbled upon these forums about installing Arch-Linux in ix2-200 and as i followed along and with few tweaks I was able to run Arch-Linux as i wanted it.
Now my OS is booted from a 16GB class 10 SDCARD using USB card reader.
And my Bay 1 and Bay 2 HDDs are mounted as separate Storages. As i will be using this storage only for kids cartoons and stuff that are easily downloadable again so i dont want RAID1 backup of these and waste my half of the storage. I know you might be thinking that is stupid using NAS for cartoons as kids can live stream, well as I am in 3rd world country we get charged alot of money for internet and on high speed internets we get charged per GB Data we use. So for me its very economical and I get to reduce to load over my internet so i can work in peace without lag.
I followed
https://kiljan.org/2016/11/15/installin ... a-ix2-200/
viewtopic.php?f=53&t=13477
Now the Problem is that my uboot shows temperature rise and decline from 25 to 51 degrees but the fan speed is always zero. And I dont want toast my hard-Drives or NAS board due to high temperature. I am looking for some help in this.
If you can point me in some direction.
The FAN rotates when i turn it with a finger. And well plugged to 12v pwer supple it rotates fine.
So the FAN is okey but uboot is not running it.
I have FTDI cable connected to serial port of NAS and below is the output of my current uboot and setenv.
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Sep 8 2009 - 09:31:54) Marvell version: 3.4.14
Mapower version: 2.0 (32MB) (2009/09/08)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:32 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0, egiga1 [PRIME]
Fan lookup table initialized.
Current remote temperature: 37
Current fan speed: 0
Hit any key to stop autoboot: 0
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x1f00000@0x100000(root)
CASset=min
MALLOC_len=1
ethprime=egiga1
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
eth1addr=00:50:43:00:02:02
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
FanHysteresis=2
FanTempStart=58
uboot_start=0x0
uboot_size=0xc0000
env_start=0xa0000
env_size=0x20000
kernel_start=0x100000
kernel_size=0x300000
initrd_start=0x540000
initrd_size=0x300000
flash_load=run make_boot_args load1 load2 boot
load1=nand read.e 0x2000000 $(kernel_start) $(kernel_size)
load2=nand read.e 0x4500000 $(initrd_start) $(initrd_size)
boot=bootm 0x2000000 0x4500000
make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=nand_mtd:;setenv bootargs $(bootargs)$(uboot_size)@$(uboot_start)(uboot),;setenv bootargs $(bootargs)$(env_size)@$(env_start)(env),;setenv bootargs $(bootargs)$(kernel_size)@$(kernel_start)(zImage),;setenv bootargs $(bootargs)$(initrd_size)@$(initrd_start)(initrd),;setenv bootargs $(bootargs)128m@0x0(flash);
iomega=123
ethaddr=AA:00:00:00:00:01
arcNumber=1682
bootargs_console=console=ttyS0,115200
bootargs_mtdparts=mtdparts=orion_nand:640k(u-boot)ro,16k(u-boot-env),-(iomega-firmware)ro
bootargs_root=root=LABEL=ROOT rw
memoffset_kernel=0x02000000
memoffset_initrd=0x08004000
bootargs_combine=setenv bootargs ${bootargs_console} ${bootargs_mtdparts} ${bootargs_root}
bootlinux=bootm ${memoffset_kernel} ${memoffset_initrd}
usb_load_firstdevice=ext2load usb 0:1 ${memoffset_kernel} /uImage; ext2load usb 0:1 ${memoffset_initrd} /uInitrd
usb_load=run bootargs_combine; usb reset; run usb_load_firstdevice; run bootlinux
sata_load_disk1=ext2load ide 0:1 ${memoffset_kernel} /uImage; ext2load ide 0:1 ${memoffset_initrd} /uInitrd
sata_load_disk2=ext2load ide 1:1 ${memoffset_kernel} /uImage; ext2load ide 1:1 ${memoffset_initrd} /uInitrd
sata_load=run bootargs_combine; ide reset; run sata_load_disk1; run sata_load_disk2; run bootlinux
bootcmd=run usb_load; run sata_load
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
hddPowerCtrl=no
enaAutoRecovery=yes
ethact=egiga1
Environment size: 2776/16380 bytes
Marvell>>