by woynitt » Sat Aug 15, 2020 9:41 pm
I've got below respond.
So if I good understand - now I should update u-boot and install OS?
$this->bbcode_second_pass_code('', 'U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Using egiga0 device
Abort
ping failed; host 192.168.1.2 is not alive
Hit any key to stop autoboot: 0
u-boot>> <INTERRUPT>
u-boot>>
u-boot>>
u-boot>>
u-boot>> printenv
arcNumber=2097
baudrate=115200
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=3
console=ttyS0,115200
ethact=egiga0
ethaddr=00:25:31:04:9D:A8
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
if_netconsole=ping $serverip
ipaddr=192.168.1.5
led_error=orange blinking
led_exit=green off
led_init=green blinking
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
preboot=run if_netconsole start_netconsole
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
serverip=192.168.1.2
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc
stderr=serial
stdin=serial
stdout=serial
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=0:1
usb_init=run usb_scan
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext2
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_scan_list=1 2 3 4
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
Environment size: 2559/131068 bytes
u-boot>>
')