Pogoplug E02 no IP after booting

[rampage]

got the latest rootfs for v2/E02, with new Uboot and env as follow:
$this->bbcode_second_pass_code('', '
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_device=0:1
usb_root=/dev/sda1
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
ethaddr=00:25:31:02:CD:08
arcNumber=3542
if_netconsole=ping $serverip
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
preboot=run if_netconsole start_netconsole
usb_rootfstype=ext3
usb_init=run usb_scan; setenv usb_root LABEL=ROOTFS
machid=dd6
serverip=192.168.2.100
ipaddr=192.168.2.4

')

and the netconsole says:

$this->bbcode_second_pass_code('', '
U-Boot 2014.07-tld-3 (Mar 31 2015 - 16:56:13)
Pogo E02
gcc (Debian 4.9.1-19) 4.9.1
GNU ld (GNU Binutils for Debian) 2.25
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
** File not found /rescueme **
** Unrecognized filesystem type **
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 727
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 716
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "rootfs", error -22
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'rootfs' errno=-22!

ubifsmount - mount UBIFS volume

Usage:
ubifsmount <volume-name>
- mount 'volume-name' volume
1 bytes read in 124 ms (0 Bytes/s)
Found bootable drive on usb 0:1
4120976 bytes read in 353 ms (11.1 MiB/s)
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-4.1.6-1-ARCH
Created: 2015-08-17 8:10:56 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4120912 Bytes = 3.9 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK


Starting kernel ...

')

After boot up , the front LED turns to solid green, but can't see the device in dhcp's client table, can't ping it either.
Attch the usb driver and looked into /var/log but there's no log other than sequence of ^@

[rampage]

using static ip configration solved the issue:
viewtopic.php?f=58&t=8045