[Solved] NSA-325v2 Only Power Led is lit

[9tawan]

Hi,

I made a mistake when I tried to install Arch. Now only the power led is on. Zyxel's utility does not see the NAS, and the NAS does not boot from USB key too.

Can you please suggest what could I do ?

Thank you.

[WarheadsSE]

What mistake?

Here is the information for a serial cable for this device.
http://zyxel.nas-central.org/wiki/Serial_port_(NSA325)#Hardware

[9tawan]

Well I put the HDD in the wrong direction, and didn't realize that it does not all the way in.

Anyway here's the boot message I've got from the serial console. (I've just got the cable today).

$this->bbcode_second_pass_quote('', ' ') __ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0xc80000.

Streaming disabled
Write allocate disabled


USB 0: host mode
[BlueDBG] reseting SoC Pex[0] 0 ...
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
[BlueDBG] reseting SoC Pex[1] 0 ...
[BlueDBG] reseting SoC Pex[1] 1 ...
[BlueDBG] reseting SoC Pex[1] 2 ...
[BlueDBG] reseting SoC Pex[1] 3 ...
[BlueDBG] reseting SoC Pex[1] 4 ...
[BlueDBG] reseting SoC Pex[1] 5 ...
[BlueDBG] reseting SoC Pex[1] 6 ...
[BlueDBG] reseting SoC Pex[1] 7 ...
[BlueDBG] reseting SoC Pex[1] 8 ...
[BlueDBG] reseting SoC Pex[1] 9 ...
[BlueDBG] reseting SoC Pex[1] 10 ...
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0xc80000, size 0xa00000

Bad block at 0xc80000 in erase block from 0xc80000 will be skipped
Reading data from 0x169f800 -- 100% complete.
10485760 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-2.6.31.8
Created: 2013-12-19 6:31:22 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5756136 Bytes = 5.5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux.............................................................................................................................................................................................................................................................................. done, booting the kernel.

[WarheadsSE]

At the prompt
$this->bbcode_second_pass_code('', 'run to_stock')

[9tawan]

Thank you. You've saved me.