ok...i'am install that sugested kernel version
viewtopic.php?f=18&t=3671 (no any changes for u-boot - its the same version and configuration => can istall alarm-iconnect):
restart
and...
$this->bbcode_second_pass_code('', '
slawek@slawek-ubuntu:~/Pulpit$ ssh lulo@alarm-iconnect
The authenticity of host 'alarm-iconnect (199.133.122.11)' can't be established.
ECDSA key fingerprint is xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx:xx.
Are you sure you want to continue connecting (yes/no)? yes
Warning: Permanently added 'alarm-iconnect,199.133.122.11' (ECDSA) to the list of known hosts.
lulo@alarm-iconnect's password:
Last login: Tue Dec 11 15:44:59 2012 from build-linux.dom
[lulo@alarm-iconnect ~]$ ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 199.133.122.11 netmask 255.255.255.0 broadcast 199.133.122.255
inet6 xxxx::xxx:xxxx:xxxx:xxxx prefixlen 64 scopeid 0x20<link>
ether xx:xx:xx:xx:xx:xx txqueuelen 1000 (Ethernet)
RX packets 1716569 bytes 142119902 (135.5 MiB)
RX errors 0 dropped 88 overruns 0 frame 0
TX packets 22017193 bytes 2389420753 (2.2 GiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 11
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 16436
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 164 bytes 11910 (11.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 164 bytes 11910 (11.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet xxx.xxx.xxx.xx netmask 255.255.255.0 broadcast 199.133.122.255
inet6 xxxx::xxx:xxxx:xxxx:xxxx prefixlen 64 scopeid 0x20<link>
ether xx:xx:xx:xx:xx:xx txqueuelen 1000 (Ethernet)
RX packets 5894 bytes 584541 (570.8 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 167 bytes 20953 (20.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[lulo@alarm-iconnect ~]$ iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11abgn ESSID:"xxxxxxxx"
Mode:Managed Frequency:5.18 GHz Access Point: xx:xx:xx:xx:xx:xx
Bit Rate=216 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:on
Link Quality=62/70 Signal level=-48 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:34 Missed beacon:0
eth0 no wireless extensions.
[lulo@alarm-iconnect ~]$ cat /etc/rc.local
#!/bin/bash
#
# /etc/rc.local: Local multi-user start-up script.
#
wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant.conf && dhcpcd wlan0
[lulo@alarm-iconnect ~]$ sudo cat /etc/wpa_supplicant.conf
[sudo] password for lulo:
ap_scan=1
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="xxxxxxxx"
scan_ssid=1
proto=WPA RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
}
[lulo@alarm-iconnect ~]$ dmesg
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.6.10-0-ARCH (root@Arch Linux ARM install) (gcc version 4.7.2 (GCC) ) #1 PREEMPT Mon Dec 10 18:15:25 MST 2012
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Iomega iConnect Wireless
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat c062e9dc, node_mem_map c0700000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0xc0000@0x0(uboot),0x20000@0xa0000(env),0x300000@0x100000(zImage),0x300000@0x540000(initrd),0x1f400000@0x980000(boot) root=/dev/sdb1 rootdelay=10
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 252688k/252688k available, 9456k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc05c01ec (5857 kB)
.init : 0xc05c1000 - 0xc05ecfc4 ( 176 kB)
.data : 0xc05ee000 - 0xc06333e0 ( 277 kB)
.bss : 0xc0633404 - 0xc06ffcb4 ( 819 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 0.000000] Console: colour dummy device 80x30
[ 15.400882] Calibrating delay loop... 990.41 BogoMIPS (lpj=4952064)
[ 15.440795] pid_max: default: 32768 minimum: 301
[ 15.440936] Security Framework initialized
[ 15.440961] AppArmor: AppArmor disabled by boot time parameter
[ 15.441032] Mount-cache hash table entries: 512
[ 15.441696] Initializing cgroup subsys cpuacct
[ 15.441716] Initializing cgroup subsys devices
[ 15.441728] Initializing cgroup subsys freezer
[ 15.441737] Initializing cgroup subsys net_cls
[ 15.441745] Initializing cgroup subsys blkio
[ 15.441754] Initializing cgroup subsys perf_event
[ 15.441773] Initializing cgroup subsys bfqio
[ 15.441880] CPU: Testing write buffer coherency: ok
[ 15.442200] Setting up static identity map for 0x4410d8 - 0x441114
[ 15.443771] devtmpfs: initialized
[ 15.446038] NET: Registered protocol family 16
[ 15.447231] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 15.448000] Kirkwood: MV88F6281-A0, TCLK=200000000.
[ 15.448020] Feroceon L2: Enabling L2
[ 15.448062] Feroceon L2: Cache support initialised.
[ 15.448755] initial MPP regs: 21111111 00003311 33331100 33333333 00000333 00000000 00000000
[ 15.448787] final MPP regs: 21111111 00003311 33331100 33333333 00000333 00000000 00000000
[ 15.449613] Kirkwood PCIe port 0:
[ 15.449621] link up
[ 15.449631] PCI: bus0 uses PCIe port 0
[ 15.449778] PCI host bridge to bus 0000:00
[ 15.449799] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
[ 15.449814] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 15.449827] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 15.449844] pci_bus 0000:00: busn_res: [bus 00-ff] is inserted under domain [bus 00-ff]
[ 15.449880] pci 0000:00:00.0: [11ab:6281] type 00 class 0x058000
[ 15.449910] pci 0000:00:00.0: reg 10: [mem 0xf1000000-0xf10fffff 64bit pref]
[ 15.449929] pci 0000:00:00.0: reg 18: [mem 0x00000000-0x0fffffff]
[ 15.449991] pci 0000:00:00.0: supports D1 D2
[ 15.450046] pci 0000:00:01.0: [168c:002a] type 00 class 0x028000
[ 15.450081] pci 0000:00:01.0: reg 10: [mem 0x40000000-0x4000ffff 64bit]
[ 15.450174] pci 0000:00:01.0: supports D1
[ 15.450187] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 15.450249] PCI: bus0: Fast back to back transfers disabled
[ 15.450265] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 15.450539] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[ 15.455735] bio: create slab <bio-0> at 0
[ 15.456174] vgaarb: loaded
[ 15.456464] SCSI subsystem initialized
[ 15.456636] libata version 3.00 loaded.
[ 15.456855] usbcore: registered new interface driver usbfs
[ 15.456917] usbcore: registered new interface driver hub
[ 15.457031] usbcore: registered new device driver usb
[ 15.457871] Switching to clocksource orion_clocksource
[ 15.472702] FS-Cache: Loaded
[ 15.483690] NET: Registered protocol family 2
[ 15.484279] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 15.484499] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 15.484612] TCP: Hash tables configured (established 8192 bind 8192)
[ 15.484653] TCP: reno registered
[ 15.484666] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 15.484690] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 15.484922] NET: Registered protocol family 1
[ 15.484980] PCI: CLS 32 bytes, default 32
[ 15.485902] audit: initializing netlink socket (disabled)
[ 15.485954] type=2000 audit(0.070:1): initialized
[ 15.587530] VFS: Disk quotas dquot_6.5.2
[ 15.587780] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 15.590250] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 15.591506] aufs 3.6
[ 15.591531] msgmni has been set to 493
[ 15.593264] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 15.593279] io scheduler noop registered
[ 15.593286] io scheduler deadline registered
[ 15.593322] io scheduler cfq registered
[ 15.593351] io scheduler bfq registered (default)
[ 15.593455] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 15.593507] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 15.627960] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 15.667963] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 15.707963] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 15.747962] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 15.752736] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 15.773366] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 15.773719] console [ttyS0] enabled
[ 15.780917] brd: module loaded
[ 15.784569] loop: module loaded
[ 15.785808] NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit), page size: 2048, OOB size: 64
[ 15.785832] Scanning device for bad blocks
[ 16.150945] 5 cmdlinepart partitions found on MTD device orion_nand
[ 16.150957] Creating 5 MTD partitions on "orion_nand":
[ 16.150972] 0x000000000000-0x0000000c0000 : "uboot"
[ 16.151382] 0x0000000a0000-0x0000000c0000 : "env"
[ 16.151733] 0x000000100000-0x000000400000 : "zImage"
[ 16.152050] 0x000000540000-0x000000840000 : "initrd"
[ 16.152369] 0x000000980000-0x00001fd80000 : "boot"
[ 16.154052] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 16.154162] libphy: mv643xx_eth smi: probed
[ 16.156158] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address xx:xx:xx:xx:xx:xx
[ 16.156211] pch_gbe: EG20T PCH Gigabit Ethernet Driver - version 1.01
[ 16.156292] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 16.156356] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 16.156389] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 16.177939] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 16.197927] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 16.198603] hub 1-0:1.0: USB hub found
[ 16.198630] hub 1-0:1.0: 1 port detected
[ 16.199061] Initializing USB Mass Storage driver...
[ 16.199176] usbcore: registered new interface driver usb-storage
[ 16.199185] USB Mass Storage support registered.
[ 16.199285] usbcore: registered new interface driver libusual
[ 16.199630] mousedev: PS/2 mouse device common for all mice
[ 16.199919] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 16.200325] orion_wdt: Initial timeout 21 sec
[ 16.200461] sdhci: Secure Digital Host Controller Interface driver
[ 16.200470] sdhci: Copyright(c) Pierre Ossman
[ 16.200539] sdhci-pltfm: SDHCI platform and OF driver helper
[ 16.200703] Registered led device: iconnect:led_level
[ 16.200827] Registered led device: iconnect:blue:power
[ 16.200940] Registered led device: iconnect:red:power
[ 16.201050] Registered led device: iconnect:blue:usb1
[ 16.201160] Registered led device: iconnect:blue:usb2
[ 16.201280] Registered led device: iconnect:blue:usb3
[ 16.201405] Registered led device: iconnect:blue:usb4
[ 16.201517] Registered led device: iconnect:blue:otb
[ 16.201749] usbcore: registered new interface driver r8712u
[ 16.202025] gre: GRE over IPv4 demultiplexor driver
[ 16.202175] TCP: cubic registered
[ 16.202188] NET: Registered protocol family 17
[ 16.202286] lib80211: common routines for IEEE802.11 drivers
[ 16.202297] lib80211_crypt: registered algorithm 'NULL'
[ 16.202361] Key type dns_resolver registered
[ 16.203007] registered taskstats version 1
[ 16.203974] console [netcon0] enabled
[ 16.203984] netconsole: network logging started
[ 16.204355] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 16.204658] rtc-mv rtc-mv: setting system clock to 2012-12-11 14:34:32 UTC (1355236472)
[ 16.205047] Waiting 10sec before mounting root device...
[ 16.517933] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 16.669031] hub 1-1:1.0: USB hub found
[ 16.669242] hub 1-1:1.0: 4 ports detected
[ 16.948119] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[ 17.060286] scsi0 : usb-storage 1-1.1:1.0
[ 17.158120] usb 1-1.2: new high-speed USB device number 4 using orion-ehci
[ 17.350962] scsi1 : usb-storage 1-1.2:1.0
[ 18.058733] scsi 0:0:0:0: Direct-Access ST925031 5AS PQ: 0 ANSI: 2 CCS
[ 18.059681] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 18.060547] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 18.061157] sd 0:0:0:0: [sda] Write Protect is off
[ 18.061176] sd 0:0:0:0: [sda] Mode Sense: 00 38 00 00
[ 18.061777] sd 0:0:0:0: [sda] Asking for cache data failed
[ 18.067317] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 18.076142] sd 0:0:0:0: [sda] Asking for cache data failed
[ 18.081691] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 18.088595] sda: sda1 sda2
[ 18.091018] sd 0:0:0:0: [sda] Asking for cache data failed
[ 18.096549] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 18.102710] sd 0:0:0:0: [sda] Attached SCSI disk
[ 18.557085] scsi 1:0:0:0: Direct-Access ADATA USB Flash Drive 1100 PQ: 0 ANSI: 0 CCS
[ 18.557842] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 18.559905] sd 1:0:0:0: [sdb] 7913472 512-byte logical blocks: (4.05 GB/3.77 GiB)
[ 18.560516] sd 1:0:0:0: [sdb] Write Protect is off
[ 18.560534] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 18.561142] sd 1:0:0:0: [sdb] No Caching mode page present
[ 18.566677] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 18.576024] sd 1:0:0:0: [sdb] No Caching mode page present
[ 18.581565] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 18.588713] sdb: sdb1
[ 18.591520] sd 1:0:0:0: [sdb] No Caching mode page present
[ 18.597050] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 18.603208] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 26.213022] EXT3-fs (sdb1): warning: maximal mount count reached, running e2fsck is recommended
[ 26.213120] kjournald starting. Commit interval 5 seconds
[ 26.214146] EXT3-fs (sdb1): using internal journal
[ 26.214160] EXT3-fs (sdb1): mounted filesystem with writeback data mode
[ 26.214201] VFS: Mounted root (ext3 filesystem) on device 8:17.
[ 26.218065] devtmpfs: mounted
[ 26.218721] Freeing init memory: 172K
[ 29.542566] systemd-udevd[87]: starting version 196
[ 30.456913] cfg80211: Calling CRDA to update world regulatory domain
[ 30.529307] cryptodev: driver 1.5 loaded.
[ 30.874410] cfg80211: World regulatory domain updated:
[ 30.874428] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 30.874440] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 30.874450] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 30.874460] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 30.874470] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 30.874479] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 31.045006] cfg80211: Calling CRDA for country: PL
[ 31.079664] cfg80211: Regulatory domain changed to country: PL
[ 31.079682] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 31.079693] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 31.079702] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 31.079712] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 31.079721] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 31.430088] ath: EEPROM regdomain: 0x60
[ 31.430102] ath: EEPROM indicates we should expect a direct regpair map
[ 31.430117] ath: Country alpha2 being used: 00
[ 31.430124] ath: Regpair used: 0x60
[ 31.440542] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 31.442530] Registered led device: ath9k-phy0
[ 31.442595] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xd0b20000, irq=9
[ 32.274396] EXT3-fs (sdb1): warning: maximal mount count reached, running e2fsck is recommended
[ 32.275428] EXT3-fs (sdb1): using internal journal
[ 32.510479] kjournald starting. Commit interval 5 seconds
[ 32.511543] EXT3-fs (sda2): using internal journal
[ 32.511557] EXT3-fs (sda2): mounted filesystem with ordered data mode
[ 32.596063] Adding 523292k swap on /dev/sda1. Priority:-1 extents:1 across:523292k
[ 37.357693] mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 47.368853] NET: Registered protocol family 10
[ 50.832706] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 54.867684] wlan0: authenticate with xx:xx:xx:xx:xx:xx
[ 54.888181] wlan0: direct probe to xx:xx:xx:xx:xx:xx (try 1/3)
[ 55.097985] wlan0: send auth to xx:xx:xx:xx:xx:xx (try 2/3)
[ 55.099504] wlan0: authenticated
[ 55.117950] wlan0: associate with xx:xx:xx:xx:xx:xx (try 1/3)
[ 55.119586] wlan0: RX AssocResp from xx:xx:xx:xx:xx:xx (capab=0x11 status=0 aid=1)
[ 55.119825] wlan0: associated
[ 55.119918] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 55.120130] cfg80211: Calling CRDA for country: PL
[ 55.170224] ath: regdomain 0x8268 updated by CountryIE
[ 55.170240] ath: EEPROM regdomain: 0x8268
[ 55.170248] ath: EEPROM indicates we should expect a country code
[ 55.170258] ath: doing EEPROM country->regdmn map search
[ 55.170266] ath: country maps to regdmn code: 0x37
[ 55.170274] ath: Country alpha2 being used: PL
[ 55.170280] ath: Regpair used: 0x37
[ 55.170442] cfg80211: Regulatory domain changed to country: PL
[ 55.170451] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 55.170462] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 55.170471] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 55.170480] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 55.170489] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[lulo@alarm-iconnect ~]$ sudo lspci -vv
[sudo] password for lulo:
00:00.0 Host bridge: Marvell Technology Group Ltd. 88F6281 [Kirkwood] ARM SoC (rev 02)
Subsystem: Marvell Technology Group Ltd. Device 11ab
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at <ignored> (64-bit, prefetchable)
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [60] Express (v1) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 unlimited
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
00:01.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01)
Subsystem: Atheros Communications Inc. Device 0200
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [60] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [90] MSI-X: Enable- Count=1 Masked-
Vector table: BAR=0 offset=00000000
PBA: BAR=0 offset=00000000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
Kernel driver in use: ath9k
[lulo@alarm-iconnect ~]$ lsmod
Module Size Used by
ipv6 265485 16
rmd160 7253 0
sha1_generic 1753 6084
hmac 2414 0
blowfish_generic 3610 0
blowfish_common 6502 1 blowfish_generic
ath9k 84417 0
ath9k_common 1787 1 ath9k
ath9k_hw 334868 2 ath9k_common,ath9k
ath 13867 3 ath9k_common,ath9k,ath9k_hw
mac80211 335788 1 ath9k
cryptodev 30567 4
cfg80211 162158 3 ath,ath9k,mac80211
rfkill 14983 2 cfg80211
mv_cesa 10309 6084
[lulo@alarm-iconnect ~]$ iw phy0 info
Wiphy phy0
Band 1:
Capabilities: 0x11ce
HT20/HT40
SM Power Save disabled
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm) (passive scanning)
* 2472 MHz [13] (20.0 dBm) (passive scanning)
* 2484 MHz [14] (disabled)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Band 2:
Capabilities: 0x11ce
HT20/HT40
SM Power Save disabled
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
Frequencies:
* 5180 MHz [36] (20.0 dBm)
* 5200 MHz [40] (20.0 dBm) (passive scanning, no IBSS)
* 5220 MHz [44] (20.0 dBm) (passive scanning, no IBSS)
* 5240 MHz [48] (20.0 dBm) (passive scanning, no IBSS)
* 5260 MHz [52] (20.0 dBm) (passive scanning, no IBSS, radar detection)
* 5280 MHz [56] (20.0 dBm) (passive scanning, no IBSS, radar detection)
* 5300 MHz [60] (20.0 dBm) (passive scanning, no IBSS, radar detection)
* 5320 MHz [64] (20.0 dBm) (passive scanning, no IBSS, radar detection)
* 5500 MHz [100] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5520 MHz [104] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5540 MHz [108] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5560 MHz [112] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5580 MHz [116] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5600 MHz [120] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5620 MHz [124] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5640 MHz [128] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5660 MHz [132] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5680 MHz [136] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5700 MHz [140] (27.0 dBm) (passive scanning, no IBSS, radar detection)
* 5745 MHz [149] (disabled)
* 5765 MHz [153] (disabled)
* 5785 MHz [157] (disabled)
* 5805 MHz [161] (disabled)
* 5825 MHz [165] (disabled)
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
* CMAC (00-0f-ac:6)
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* P2P-client
* P2P-GO
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed, WDS, P2P-client } <= 2048, #{ AP, P2P-GO } <= 8,
total <= 2048, #channels <= 1
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* tdls_mgmt
* tdls_oper
* probe_client
* set_noack_map
* register_beacons
* testmode
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
Device supports RSN-IBSS.
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
[lulo@alarm-iconnect ~]$ iw wlan0 info
Interface wlan0
ifindex 3
wdev 0x1
addr xx:xx:xx:xx:xx:xx
type managed
wiphy 0
channel 36 (5180 MHz) HT40+
[lulo@alarm-iconnect ~]$
')
Probably everyting is ok
...no any debug messages (boot system).
TRANSFER:
(199.133.122.17 - alrm-iconnect-wifi from my iConnect
199.133.122.1 - router
199.133.122.10 - PC computer)
From router Netgear WNDR3800 (software: last gargoyle-pl by obsy -
http://openrouter.info)
162 Mb/s - speed connection after can connect alarm-iconnect-wifi to my router (different card wifi - not orginal:
viewtopic.php?f=6&t=3135 )
Real transfer read wifi (ftp - big file: 32 GiB) : 32 MB/s (
) - probably max speed usb||external usb-sata||this disk (real distance from this devices to my LAN: alarm-iconnect-wifi <=> router = 2.5 m )
(smb): 6.8-12 MB/s (
)
IMPORTANT: not installed any internal or any external antennas for my iconnect wifi card...any !
he...
P.S.
1 question:
$this->bbcode_second_pass_code('', '
lulo@alarm-iconnect ~]$ iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11abgn ESSID:"xxxxxxxx"
Mode:Managed Frequency:5.18 GHz Access Point: xx:xx:xx:xx:xx:xx
Bit Rate=216 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:on
Link Quality=62/70 Signal level=-48 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:34 Missed beacon:0
eth0 no wireless extensions.
')
$this->bbcode_second_pass_code('', '
Invalid misc:34
')
how to fix - it is important bug ?
2 question:
$this->bbcode_second_pass_code('', '
[lulo@alarm-iconnect ~]$ cat /sys/block/sdb/queue/scheduler
noop deadline cfq [bfq]
[lulo@alarm-iconnect ~]$
')
Probably bfq not working for my iConnect (old u-boot)
$this->bbcode_second_pass_code('', '
[lulo@alarm-iconnect ~]$ sudo fw_printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
bootargs=console=ttyS0,115200 ramdisk=32768 mtdparts=orion_nand:0xc0000@0x0(uboot),0x20000@0xa0000(env),0x300000@0x100000(zImage),0x300000@0x540000(initrd),0x1f400000@0x980000(boot)
ethprime=egiga0
ethact=egiga0
serverip=192.168.100.70
ipaddr=192.168.100.71
usbstart=usb start
run_diag=yes
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x1ff00000@0x100000(root)
CASset=min
MALLOC_len=1
bootargs_root=root=/dev/nfs rw
bootargs_end=:::orion:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethaddr=xx:xx:xx:xx:xx:xx
ethmtu=1500
eth1addr=xx:xx:xx:xx:xx:xx
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(xx:xx:xx:xx:xx:xx,x:x:x:x),mtu=1500
usb0Mode=host
yuk_ethaddr=xx:xx:xx:xx:xx:xx
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
uboot_start=0x0
uboot_size=0xc0000
env_start=0xa0000
env_size=0x20000
kernel_start=0x100000
kernel_size=0x300000
initrd_start=0x540000
initrd_size=0x300000
flash_load=run make_boot_args load1 load2 boot
load1=nand read.e 0x2000000 $(kernel_start) $(kernel_size)
load2=nand read.e 0x4500000 $(initrd_start) $(initrd_size)
boot=bootm 0x2000000 0x4500000
nandEcc=1bit
iomega=123
make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:;setenv bootargs $(bootargs)$(uboot_size)@$(uboot_start)(uboot),;setenv bootargs $(bootargs)$(env_size)@$(env_start)(env),;setenv bootargs $(bootargs)$(kernel_size)@$(kernel_start)(zImage),;setenv bootargs $(bootargs)$(initrd_size)@$(initrd_start)(initrd),;setenv bootargs $(bootargs)$(boot_size)@$(boot_start)(boot)
boot_start=0x980000
boot_size=0x1f400000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
hddPowerCtrl=no
enaAutoRecovery=yes
pcieTune=no
usb_scan_1=setenv usb 0:1; setenv dev sda1
usb_scan_2=setenv usb 1:1; setenv dev sdb1
usb_scan_3=setenv usb 2:1; setenv dev sdc1
usb_scan_4=setenv usb 3:1; setenv dev sdd1
usb_scan_5=setenv usb 0:1; setenv dev sda2
usb_scan_6=setenv usb 1:1; setenv dev sdb2
usb_scan_7=setenv usb 2:1; setenv dev sdc2
usb_scan_8=setenv usb 3:1; setenv dev sdd2
bootcmd_usb_1=run usb_scan_1;run make_usb_bootargs;ext2load usb $(usb) 0x00800000 /boot/uImage;bootm 0x00800000
bootcmd_usb_2=run usb_scan_2;run make_usb_bootargs;ext2load usb $(usb) 0x00800000 /boot/uImage;bootm 0x00800000
bootcmd_usb_3=run usb_scan_3;run make_usb_bootargs;ext2load usb $(usb) 0x00800000 /boot/uImage;bootm 0x00800000
bootcmd_usb_4=run usb_scan_4;run make_usb_bootargs;ext2load usb $(usb) 0x00800000 /boot/uImage;bootm 0x00800000
bootcmd_usb_5=run usb_scan_5;run make_usb_bootargs;ext2load usb $(usb) 0x00800000 /uImage;bootm 0x00800000
bootcmd_usb_6=run usb_scan_6;run make_usb_bootargs;ext2load usb $(usb) 0x00800000 /uImage;bootm 0x00800000
bootcmd_usb_7=run usb_scan_7;run make_usb_bootargs;ext2load usb $(usb) 0x00800000 /uImage;bootm 0x00800000
bootcmd_usb_8=run usb_scan_8;run make_usb_bootargs;ext2load usb $(usb) 0x00800000 /uImage;bootm 0x00800000
make_usb_bootargs=run make_boot_args;setenv bootargs $(bootargs) root=/dev/$(dev) rootdelay=10
bootcmd_usb=usb start;run bootcmd_usb_1;run bootcmd_usb_2;run bootcmd_usb_3;run bootcmd_usb_4;run bootcmd_usb_5;run bootcmd_usb_6;run bootcmd_usb_7;run bootcmd_usb_8
bootcmd=run bootcmd_usb; run flash_load
arcNumber=2870
[lulo@alarm-iconnect ~]$
')