pcduino3 nano - no net support

[avd]

Boot is ok, but eth0 is down.
I found similar topic viewtopic.php?f=60&t=8561&p=45848&hilit=pcduino3#p45848
Is there any chance to solve it?

this is my boot log:
$this->bbcode_second_pass_code('', '
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.0.4-2-ARCH (builduser@leming) (gcc version 4.9.2 20150304 (prerelease) (GCC) ) #1 SMP Fri May 22 19:02:31 MDT 2015
[ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: LinkSprite pcDuino3
[ 0.000000] cma: Reserved 16 MiB at 0x7f000000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat c0fcb300, node_mem_map eeef9000
[ 0.000000] Normal zone: 1710 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 67584 pages, LIFO batch:15
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] PERCPU: Embedded 12 pages/cpu @eeec8000 s17024 r8192 d23936 u49152
[ 0.000000] pcpu-alloc: s17024 r8192 d23936 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260434
[ 0.000000] Kernel command line: console=ttyS0,115200 root=PARTUUID=e796fad5-01 rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1004832K/1048576K available (10075K kernel code, 957K rwd
ata, 4116K rodata, 1040K init, 908K bss, 27360K reserved, 16384K cma-reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0de3fc0 (14192 kB)
.init : 0xc0de4000 - 0xc0ee8000 (1040 kB)
.data : 0xc0ee8000 - 0xc0fd74f0 ( 958 kB)
.bss : 0xc0fd74f0 - 0xc10ba510 ( 909 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] GIC physical location is 0x1c81000
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.000024] Switching to timer-based delay loop, resolution 41ns
[ 0.002021] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
[ 0.003192] Console: colour dummy device 80x30
[ 0.003228] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=120000)
[ 0.003246] pid_max: default: 32768 minimum: 301
[ 0.003374] Security Framework initialized
[ 0.003577] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.003591] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.004460] Initializing cgroup subsys blkio
[ 0.004491] Initializing cgroup subsys memory
[ 0.004533] Initializing cgroup subsys devices
[ 0.004552] Initializing cgroup subsys freezer
[ 0.004570] Initializing cgroup subsys net_cls
[ 0.004587] Initializing cgroup subsys perf_event
[ 0.004604] Initializing cgroup subsys net_prio
[ 0.004683] CPU: Testing write buffer coherency: ok
[ 0.004737] ftrace: allocating 36930 entries in 109 pages
[ 0.065507] /cpus/cpu@0 missing clock-frequency property
[ 0.065541] /cpus/cpu@1 missing clock-frequency property
[ 0.065556] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.065651] Setting up static identity map for 0x4090af88 - 0x4090b020
[ 0.069048] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.069163] Brought up 2 CPUs
[ 0.069186] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[ 0.069194] CPU: All CPU(s) started in HYP mode.
[ 0.069200] CPU: Virtualization extensions available.
[ 0.070093] devtmpfs: initialized
[ 0.071369] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[ 0.073058] xor: measuring software checksum speed
[ 0.120163] arm4regs : 1153.600 MB/sec
[ 0.170234] 8regs : 684.000 MB/sec
[ 0.220301] 32regs : 844.800 MB/sec
[ 0.270375] neon : 669.600 MB/sec
[ 0.270385] xor: using function: arm4regs (1153.600 MB/sec)
[ 0.170234] 8regs : 684.000 MB/sec
[ 0.220301] 32regs : 844.800 MB/sec
[ 0.270375] neon : 669.600 MB/sec
[ 0.270385] xor: using function: arm4regs (1153.600 MB/sec)
[ 0.270548] pinctrl core: initialized pinctrl subsystem
[ 0.279123] NET: Registered protocol family 16
[ 0.281129] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.291385] No ATAGs?
[ 0.291441] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.291453] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.293389] Serial: AMBA PL011 UART driver
[ 0.401137] raid6: int32x1 107 MB/s
[ 0.486058] raid6: int32x2 144 MB/s
[ 0.571607] raid6: int32x4 127 MB/s
[ 0.656829] raid6: int32x8 115 MB/s
[ 0.741453] raid6: neonx1 426 MB/s
[ 0.826602] raid6: neonx2 579 MB/s
[ 0.911840] raid6: neonx4 588 MB/s
[ 0.997018] raid6: neonx8 428 MB/s
[ 0.997027] raid6: using algorithm neonx4 (588 MB/s)
[ 0.997035] raid6: using intx1 recovery algorithm
[ 0.999493] reg-fixed-voltage ahci-5v: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@0, deferring probe
[ 0.999523] platform ahci-5v: Driver reg-fixed-voltage requests probe deferral
[ 0.999560] reg-fixed-voltage usb1-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[ 0.999576] platform usb1-vbus: Driver reg-fixed-voltage requests probe deferral
[ 0.999606] reg-fixed-voltage usb2-vbus: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0,deferring probe
[ 0.999622] platform usb2-vbus: Driver reg-fixed-voltage requests probe deferral
[ 1.004081] vgaarb: loaded
[ 1.005383] SCSI subsystem initialized
[ 1.005727] libata version 3.00 loaded.
[ 1.006116] usbcore: registered new interface driver usbfs
[ 1.006212] usbcore: registered new interface driver hub
[ 1.006294] usbcore: registered new device driver usb
[ 1.007740] media: Linux media interface: v0.10
[ 1.007817] Linux video capture interface: v2.00
[ 1.007939] pps_core: LinuxPPS API ver. 1 registered
[ 1.007949] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.007982] PTP clock support registered
[ 1.008074] EDAC MC: Ver: 3.0.0
[ 1.009444] Advanced Linux Sound Architecture Driver Initialized.
[ 1.010310] NetLabel: Initializing
[ 1.010324] NetLabel: domain hash size = 128
[ 1.010330] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.010396] NetLabel: unlabeled traffic allowed by default
[ 1.010707] Switched to clocksource arch_sys_counter
[ 1.076722] NET: Registered protocol family 2
[ 1.077843] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 1.077946] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.078074] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.078161] TCP: reno registered
[ 1.078179] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.078238] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.078523] NET: Registered protocol family 1
[ 1.078958] RPC: Registered named UNIX socket transport module.
[ 1.078974] RPC: Registered udp transport module.
[ 1.078981] RPC: Registered tcp transport module.
[ 1.078989] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.079017] PCI: CLS 0 bytes, default 64
[ 1.080031] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 1.082509] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 1.091471] zpool: loaded
[ 1.091496] zbud: loaded
[ 1.092146] VFS: Disk quotas dquot_6.5.2
[ 1.092387] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.094459] NFS: Registering the id_resolver key type
[ 1.094530] Key type id_resolver registered
[ 1.094539] Key type id_legacy registered
[ 1.094568] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.097611] bounce: pool size: 64 pages
[ 1.097897] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.098076] io scheduler noop registered
[ 1.098093] io scheduler deadline registered
[ 1.098311] io scheduler cfq registered (default)
[ 1.099986] platform 1c13400.phy: Driver sun4i-usb-phy requests probe deferral
[ 1.105409] sun7i-a20-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 1.180323] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 1.183783] console [ttyS0] disabled
[ 1.204024] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 40, base_baud = 1500000) is a U6_16550A
[ 2.012654] console [ttyS0] enabled
[ 2.016689] Serial: AMBA driver
[ 2.021404] [drm] Initialized drm 1.1.0 20060810
[ 2.034179] loop: module loaded
[ 2.038987] Loading iSCSI transport class v2.0-870.
[ 2.044564] iscsi: registered transport (tcp)
[ 2.049955] platform 1c18000.sata: Driver ahci-sunxi requests probe deferral
[ 2.063129] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.069729] ehci-pci: EHCI PCI platform driver
[ 2.074287] ehci-platform: EHCI generic platform driver
[ 2.079783] platform 1c14000.usb: Driver ehci-platform requests probe deferral
[ 2.087147] platform 1c1c000.usb: Driver ehci-platform requests probe deferral
[ 2.094506] ehci-mxc: Freescale On-Chip EHCI Host driver
[ 2.099947] ehci-omap: OMAP-EHCI Host Controller driver
[ 2.105311] ehci-orion: EHCI orion driver
[ 2.109453] ehci-exynos: EHCI EXYNOS driver
[ 2.113783] tegra-ehci: Tegra EHCI driver
[ 2.117937] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.124165] ohci-pci: OHCI PCI platform driver
[ 2.128703] ohci-platform: OHCI generic platform driver
[ 2.134126] platform 1c14400.usb: Driver ohci-platform requests probe deferral
[ 2.141470] platform 1c1c400.usb: Driver ohci-platform requests probe deferral
[ 2.148803] ohci-exynos: OHCI EXYNOS driver
[ 2.153151] ohci-omap3: OHCI OMAP3 driver
[ 2.157388] usbcore: registered new interface driver uas
[ 2.162817] usbcore: registered new interface driver usb-storage
[ 2.168896] usbcore: registered new interface driver ums-cypress
[ 2.174993] usbcore: registered new interface driver ums_eneub6250
[ 2.181242] usbcore: registered new interface driver ums-freecom
[ 2.187325] usbcore: registered new interface driver ums-isd200
[ 2.193310] usbcore: registered new interface driver ums-usbat
[ 2.204401] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0
[ 2.211255] sunxi-rtc 1c20d00.rtc: RTC enabled
[ 2.216136] i2c /dev entries driver
[ 2.221190] axp20x 0-0034: AXP20x variant AXP209 found
[ 2.234824] input: axp20x-pek as /devices/platform/soc@01c00000/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input0
[ 2.245375] axp20x-regulator axp20x-regulator: regulators node not found
[ 2.254818] axp20x 0-0034: AXP20X driver loaded
[ 2.264012] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=1)
[ 2.273163] Driver 'mmcblk' needs updating - please use bus_type methods
[ 2.279963] sdhci: Secure Digital Host Controller Interface driver
[ 2.286158] sdhci: Copyright(c) Pierre Ossman
[ 2.291110] Synopsys Designware Multimedia Card Interface Driver
[ 2.298237] sunxi-mmc 1c0f000.mmc: No vqmmc regulator found
[ 2.304550] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[ 2.335994] sunxi-mmc 1c0f000.mmc: base:0xf00aa000 irq:26
[ 2.341646] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.348825] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.355827] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.361959] usbcore: registered new interface driver usbhid
[ 2.367589] usbhid: USB HID core driver
[ 2.372037] ashmem: initialized
[ 2.382732] oprofile: using timer interrupt.
[ 2.387379] TCP: cubic registered
[ 2.391589] NET: Registered protocol family 10
[ 2.397628] mip6: Mobile IPv6
[ 2.400663] NET: Registered protocol family 17
[ 2.405336] Key type dns_resolver registered
[ 2.414471] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.420618] ThumbEE CPU extension supported.
[ 2.420643] Registering SWP/SWPB emulation handler
[ 2.421615] registered taskstats version 1
[ 2.424572] Btrfs loaded
[ 2.440801] mmc0: new high speed SDHC card at address b368
[ 2.446968] mmcblk0: mmc0:b368 NCard 7.48 GiB
[ 2.453340] mmcblk0: p1
[ 2.465829] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[ 2.473384] ahci-sunxi 1c18000.sata: SSS flag set, parallel bus scan disabled
[ 2.480557] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 2.489531] ahci-sunxi 1c18000.sata: flags: ncq sntf stag pm led clo only pio slum part ccc
[ 2.499120] scsi host0: ahci-sunxi
[ 2.502962] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 29
[ 2.512016] ehci-platform 1c14000.usb: EHCI Host Controller
[ 2.517999] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[ 2.526029] ehci-platform 1c14000.usb: irq 27, io mem 0x01c14000
[ 2.540733] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[ 2.547093] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.553902] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.561134] usb usb1: Product: EHCI Host Controller
[ 2.566021] usb usb1: Manufacturer: Linux 4.0.4-2-ARCH ehci_hcd
[ 2.571948] usb usb1: SerialNumber: 1c14000.usb
[ 2.577354] hub 1-0:1.0: USB hub found
[ 2.581208] hub 1-0:1.0: 1 port detected
[ 2.586657] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 2.592643] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[ 2.600729] ehci-platform 1c1c000.usb: irq 30, io mem 0x01c1c000
[ 2.615743] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 2.622094] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.628903] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.636134] usb usb2: Product: EHCI Host Controller
[ 2.641022] usb usb2: Manufacturer: Linux 4.0.4-2-ARCH ehci_hcd
[ 2.646948] usb usb2: SerialNumber: 1c1c000.usb
[ 2.652305] hub 2-0:1.0: USB hub found
[ 2.656152] hub 2-0:1.0: 1 port detected
[ 2.661588] ohci-platform 1c14400.usb: Generic Platform OHCI controller
[ 2.668590] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
[ 2.676606] ohci-platform 1c14400.usb: irq 28, io mem 0x01c14400
[ 2.739967] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.746782] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.754012] usb usb3: Product: Generic Platform OHCI controller
[ 2.759951] usb usb3: Manufacturer: Linux 4.0.4-2-ARCH ohci_hcd
[ 2.765885] usb usb3: SerialNumber: 1c14400.usb
[ 2.771563] hub 3-0:1.0: USB hub found
[ 2.775365] hub 3-0:1.0: 1 port detected
[ 2.780886] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[ 2.787888] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[ 2.795907] ohci-platform 1c1c400.usb: irq 31, io mem 0x01c1c400
[ 2.835738] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.859977] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.866795] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.874027] usb usb4: Product: Generic Platform OHCI controller
[ 2.879969] usb usb4: Manufacturer: Linux 4.0.4-2-ARCH ohci_hcd
[ 2.885902] usb usb4: SerialNumber: 1c1c400.usb
[ 2.891419] hub 4-0:1.0: USB hub found
[ 2.895223] hub 4-0:1.0: 1 port detected
[ 2.901447] input: gpio_keys as /devices/platform/gpio_keys/input/input1
[ 2.908463] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01 00:00:16 UTC (16)
[ 2.916501] sr_init: No PMIC hook to init smartreflex
[ 2.921792] sr_init: platform driver register failed for SR
[ 2.933894] Unable to find PPMU node
[ 2.937562] exynos5-bus-int: probe of exynos5-bus-int failed with error -2
[ 2.944534] PM: Hibernation image not present or could not be loaded.
[ 2.944566] vcc5v0: disabling
[ 2.947556] vcc3v0: disabling
[ 2.950669] ALSA device list:
[ 2.953657] No soundcards found.
[ 2.958783] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities
[ 2.967847] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities
[ 3.389806] random: nonblocking pool is initialized
[ 3.400289] EXT4-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is recommended
[ 3.417670] EXT4-fs (mmcblk0p1): recovery complete
[ 3.428579] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 3.436753] VFS: Mounted root (ext4 filesystem) on device 179:1.
[ 3.446130] devtmpfs: mounted
[ 3.451085] Freeing unused kernel memory: 1040K (c0de4000 - c0ee8000)
[ 3.711528] systemd[1]: systemd 219 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD +IDN)
[ 3.730050] systemd[1]: Detected architecture 'arm'.
[ 3.747484] systemd[1]: Set hostname to <alarm>.
[ 3.999496] systemd[1]: Unit type .busname is not supported on this system.
[ 4.274602] systemd[1]: Cannot add dependency job for unit org.freedesktop.resolve1.busname, ignoring: Unit org.freedesktop.resolve1.busname failed to load: No such file or directory.
[ 4.291531] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
[ 4.320934] systemd[1]: Reached target Encrypted Volumes.
[ 4.326630] systemd[1]: Starting Encrypted Volumes.
[ 4.340906] systemd[1]: Reached target Remote File Systems.
[ 4.346674] systemd[1]: Starting Remote File Systems.
[ 4.360955] systemd[1]: Created slice Root Slice.
[ 4.365927] systemd[1]: Starting Root Slice.
[ 4.380951] systemd[1]: Created slice System Slice.
[ 4.386129] systemd[1]: Starting System Slice.
[ 4.400944] systemd[1]: Listening on Journal Socket.
[ 4.406194] systemd[1]: Starting Journal Socket.
[ 4.411575] systemd[1]: Mounted Huge Pages File System.
[ 4.421300] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 4.441965] systemd[1]: Mounting Debug File System...
[ 4.470210] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 4.548577] systemd[1]: Listening on Journal Audit Socket.
[ 4.565958] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 4.572312] systemd[1]: Starting LVM2 metadata daemon socket.
[ 4.585936] systemd[1]: Listening on udev Control Socket.
[ 4.605909] systemd[1]: Listening on Delayed Shutdown Socket.
[ 4.611867] systemd[1]: Starting Delayed Shutdown Socket.
[ 4.625904] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 4.632648] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 4.650919] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 4.658092] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 4.675919] systemd[1]: Listening on Journal Socket (/dev/log).
[ 4.682055] systemd[1]: Starting Journal Socket (/dev/log).
[ 4.692191] systemd[1]: Starting Journal Service...
[ 4.711073] systemd[1]: Starting Setup Virtual Console...
[ 4.726628] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 4.735461] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 4.756011] systemd[1]: Created slice User and Session Slice.
[ 4.762710] systemd[1]: Starting User and Session Slice.
[ 4.781015] systemd[1]: Reached target Slices.
[ 4.785681] systemd[1]: Starting Slices.
[ 4.796374] systemd[1]: Mounting Temporary Directory...
[ 4.799524] systemd-journald[90]: Failed to set file attributes: Inappropriate ioctl for device
[ 4.831077] systemd[1]: Listening on networkd rtnetlink socket.
[ 4.837332] systemd[1]: Starting networkd rtnetlink socket.
[ 4.855982] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 4.865653] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 4.878567] systemd[1]: Mounting POSIX Message Queue File System...
[ 4.897200] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 4.911010] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 4.931014] systemd[1]: Reached target Paths.
[ 4.940839] systemd[1]: Starting Paths.
[ 4.990438] systemd-journald[90]: File /var/log/journal/a8f70f8291e44e469497f6c3d4961999/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 5.007095] systemd[1]: Started Load Kernel Modules.
[ 5.012999] systemd[1]: Mounted Configuration File System.
[ 5.018875] systemd[1]: Mounted FUSE Control File System.
[ 5.036228] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 5.042990] systemd[1]: Starting system-serial\x2dgetty.slice.
[ 5.061055] systemd[1]: Listening on udev Kernel Socket.
[ 5.066609] systemd[1]: Starting udev Kernel Socket.
[ 5.076565] systemd[1]: Starting udev Coldplug all Devices...
[ 5.111087] systemd[1]: Created slice system-getty.slice.
[ 5.116777] systemd[1]: Starting system-getty.slice.
[ 5.126457] systemd[1]: Starting Apply Kernel Variables...
[ 5.149305] systemd[1]: Started Set Up Additional Binary Formats.
[ 5.166056] systemd[1]: Reached target Swap.
[ 5.170568] systemd[1]: Starting Swap.
[ 5.201058] systemd[1]: Mounted POSIX Message Queue File System.
[ 5.226094] systemd[1]: Mounted Debug File System.
[ 5.241103] systemd[1]: Mounted Temporary Directory.
[ 5.261092] systemd[1]: Started Remount Root and Kernel File Systems.
[ 5.286081] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 5.306051] systemd[1]: Started Setup Virtual Console.
[ 5.331152] systemd[1]: Started Apply Kernel Variables.
[ 5.356148] systemd[1]: Started Journal Service.
[ 5.775238] systemd-journald[90]: Received request to flush runtime journal from PID 1
[ 8.175310] stmmaceth 1c50000.ethernet: no regulator found
[ 8.242967] stmmaceth 1c50000.ethernet: no reset control found
[ 8.276408] Ring mode enabled
[ 8.279487] No HW DMA feature register supported
[ 8.284105] Normal descriptors
[ 8.287515] TX Checksum insertion supported
[ 8.441547] libphy: stmmac: probed
[ 8.444975] eth0: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[ 8.451371] eth0: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
[ 10.024495] stmmac_hw_setup: DMA engine initialization failed
[ 10.030308] stmmac_open: Hw setup failed

//------------------- no net connection!!!

[root@alarm ~]# ifconfig
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 160 bytes 12640 (12.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 160 bytes 12640 (12.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

[root@alarm ~]# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 02:07:07:43:22:60 brd ff:ff:ff:ff:ff:ff

[root@alarm ~]# ip link set eth0 up
[ 3465.168033] stmmac_hw_setup: DMA engine initialization failed
[ 3465.173824] stmmac_open: Hw setup failed
RTNETLINK answers: Device or resource busy
')

[thermionix]

also having issues with a pcDuino3 Nano
$this->bbcode_second_pass_code('', 'RTNETLINK answers: Device or resource busy')

any advice would be super appreciated!

[thermionix]

Ok, fixed!
Recompiled u-Boot from mainline, to suit the board

$this->bbcode_second_pass_code('', 'git clone git://git.denx.de/u-boot.git
cd u-boot
make CROSS_COMPILE=arm-linux-gnueabihf- Linksprite_pcDuino3_Nano_defconfig
make CROSS_COMPILE=arm-linux-gnueabihf-

mkdir -p ../u-boot-output
cp u-boot-sunxi-with-spl.bin spl/sunxi-spl.bin u-boot.img ../u-boot-output

cp u-boot.dtb ../u-boot-output/sun7i-a20-pcduino3-nano.dtb

# Zero and Write the new bootloader to the sdcard:
sudo dd if=/dev/zero of=/dev/sdX bs=1M count=8
sudo dd if=u-boot-sunxi-with-spl.bin of=/dev/sdX bs=1024 seek=8
sync

# Also copy sun7i-a20-pcduino3-nano.dtb into /boot/dtbs')

Note1 - I zero'd more of the sdcard than may be needed - my root partition is on an SSD

Note2 - on arch, the cross compiler I'm using is the only one currently re-added to the aur since the switch to aur4 - arm-frc-linux-gnueabi-gcc

I'll submit a pull-request to the ArchLinuxArm to include pcduino3-nano in the uBoot compilation of supported boards

[thermionix]

I've temporarily added them to a github repo;

https://github.com/Thermionix/arch-satn ... Duino-Nano