Utilite *Appears* Frozen on Boot

[joshbradfield]

tldr: boot normal, after printing "Starting Permit User Sessions..." nothing happens.

I recently purchased a Utilite "value" box.

I followed the instructions, downloaded the latest package, formatted a new SD card, loaded the boot and root partitions etc.

uBoot appears to work fine (i'll admit i dont know how to judge this) loads the image and starts the kernel.

I get the "Welcome to Arch Linux ARM!" message, the system appears to boot normally (compared to my desktop Arch installation) but after printing "Starting Permit User Sessions..." nothing happens.

I cannot find the device on the network using nmap and my router does not recall giving out any new ip addresses.

Whats the best way to approach this problem?

[joshbradfield]

Just in case :

uBoot output:
$this->bbcode_second_pass_code('', '
U-Boot 2009.08-cm-fx6-0.91+tools (Nov 19 2013 - 15:27:59)

CPU: Freescale i.MX6 family TO6.4 at 792 MHz
Temperature: 34 C, calibration data 0x57d5095f
mx6q pll1: 792MHz
mx6q pll2: 528MHz
mx6q pll3: 480MHz
mx6q pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
nfc clock : 11000000Hz
Board: CM-FX6:[ WDOG ]
Boot Device: SD
I2C: ready
RAM Configuration:
Bank #0: 10000000 512 MB
NAND: No NAND device found!!!
0 MiB
MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2
JEDEC ID: 0xbf:0x25:0x41
Reading SPI NOR flash 0xc0000 [0x2000 bytes] -> ram 0x17e030e0
SUCCESS

In: serial
Out: serial
Err: serial
Net: got MAC address from IIM: 00:00:00:00:00:00
FEC0
Hit any key to stop autoboot: 3 2 1 0
mmc2 is current device
reading boot.scr

** Unable to read "boot.scr" from mmc 2:1 **
reading uImage-cm-fx6

4440656 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 10800000 ...
Image Name: Linux-3.0.35-16-ARCH
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4440592 Bytes = 4.2 MB
Load Address: 10008000
Entry Point: 10008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
')

[joshbradfield]

Arch Linux ARM Boot Output :

$this->bbcode_second_pass_code('', '
Starting kernel ...

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.35-16-ARCH (nobody@root-chroot-copy) (gcc version 4.8.2 20131219 (prerelease) (GCC) ) #1 SMP Sun May 25 17:19:33 MDT 2014
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Compulab CM-FX6
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU identified as i.MX6DL/SOLO, silicon rev 1.1
[ 0.000000] PERCPU: Embedded 7 pages/cpu @cbc05000 s6336 r8192 d14144 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113664
[ 0.000000] Kernel command line: console=ttymxc3,115200 root=/dev/mmcblk0p2 rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 2097152 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 448MB = 448MB total
[ 0.000000] Memory: 443004k/443004k available, 81284k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xf4600000 - 0xffe00000 ( 184 MB)
[ 0.000000] vmalloc : 0xe0800000 - 0xf2000000 ( 280 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0046000 ( 248 kB)
[ 0.000000] .text : 0xc0046000 - 0xc08191a8 (8013 kB)
[ 0.000000] .data : 0xc081a000 - 0xc08742a0 ( 361 kB)
[ 0.000000] .bss : 0xc08742c4 - 0xc08f01cc ( 496 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:624
[ 0.000000] MXC GPIO hardware
[ 0.000000] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
[ 0.000000] Set periph_clk's parent to pll2_pfd_400M!
[ 0.000000] arm_max_freq=1GHz
[ 0.000000] MXC_Early serial console at MMIO 0x21f0000 (options '115200')
[ 0.000000] bootconsole [ttymxc3] enabled
[ 0.000000] Console: colour dummy device 80x30
[ 0.239889] Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
[ 0.328202] pid_max: default: 32768 minimum: 301
[ 0.333046] Security Framework initialized
[ 0.337279] Mount-cache hash table entries: 512
[ 0.342586] Initializing cgroup subsys cpuacct
[ 0.347095] Initializing cgroup subsys memory
[ 0.351528] Initializing cgroup subsys devices
[ 0.355989] Initializing cgroup subsys freezer
[ 0.360446] Initializing cgroup subsys blkio
[ 0.364764] Initializing cgroup subsys perf_event
[ 0.369610] CPU: Testing write buffer coherency: ok
[ 0.374678] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.383421] Brought up 1 CPUs
[ 0.386403] SMP: Total of 1 processors activated (1581.05 BogoMIPS).
[ 0.393425] devtmpfs: initialized
[ 0.416176] print_constraints: dummy:
[ 0.420214] NET: Registered protocol family 16
[ 0.426020] print_constraints: vddpu: 725 <--> 1300 mV at 1150 mV fast normal
[ 0.433426] print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
[ 0.441029] print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
[ 0.448520] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
[ 0.456144] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
[ 0.463617] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
[ 0.511227] cpu regulator mode:ldo_enable
[ 0.516939] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.523779] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
[ 0.531111] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.536989] L310 cache controller enabled
[ 0.541012] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02050000, Cache size: 524288 B
[ 0.553921] bio: create slab <bio-0> at 0
[ 0.559432] mxs-dma mxs-dma-apbh: initialized
[ 0.563919] print_constraints: ads7846_vcc: 3300 mV
[ 0.569000] print_constraints: vmmc: 3300 mV
[ 0.573597] vgaarb: loaded
[ 0.576561] SCSI subsystem initialized
[ 0.580761] spi_imx imx6q-ecspi.0: probed
[ 0.584955] spi_imx imx6q-ecspi.1: probed
[ 0.589182] usbcore: registered new interface driver usbfs
[ 0.594717] usbcore: registered new interface driver hub
[ 0.600147] usbcore: registered new device driver usb
[ 0.605211] Freescale USB OTG Driver loaded, $Revision: 1.55 $
[ 0.631141] imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
[ 0.638963] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.645826] Switching to clocksource mxc_timer1
[ 0.656506] NET: Registered protocol family 2
[ 0.661094] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.668673] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.676128] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.682955] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.689499] TCP reno registered
[ 0.692662] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.698534] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.705204] NET: Registered protocol family 1
[ 0.709886] RPC: Registered named UNIX socket transport module.
[ 0.715846] RPC: Registered udp transport module.
[ 0.720572] RPC: Registered tcp transport module.
[ 0.725287] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.731958] _regulator_get: etb supply vcore not found, using dummy regulator
[ 0.739332] _regulator_get: etm.0 supply vcore not found, using dummy regulator
[ 0.746805] Static Power Management for Freescale i.MX6
[ 0.752056] wait mode is enabled for i.MX6
[ 0.756221] cpaddr = e0820000 suspend_iram_base=e08ac000
[ 0.761632] PM driver module loaded
[ 0.765286] IMX usb wakeup probe
[ 0.768859] add wake up source irq 75
[ 0.777587] IMX usb wakeup probe
[ 0.781005] i.MXC CPU frequency driver
[ 0.795830] VFS: Disk quotas dquot_6.5.2
[ 0.800091] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.808720] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.815532] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.822117] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[ 0.832330] msgmni has been set to 865
[ 0.840164] alg: No test for fcrypt (fcrypt-generic)
[ 0.850360] alg: No test for stdrng (krng)
[ 0.854891] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.862492] io scheduler noop registered
[ 0.866425] io scheduler deadline registered
[ 0.870846] io scheduler cfq registered (default)
[ 0.876356] imx-sdma imx-sdma: loaded firmware 1.1
[ 0.882953] imx-sdma imx-sdma: initialized
[ 0.976083] Serial: IMX driver
[ 0.979249] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
[ 0.986114] imx-uart.3: ttymxc3 at MMIO 0x21f0000 (irq = 61) is a IMX
[ 0.992611] console [ttymxc3] enabled, bootconsole disabled
[ 0.992611] console [ttymxc3] enabled, bootconsole disabled
[ 1.004097] imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
[ 1.010875] imx-uart.4: ttymxc4 at MMIO 0x21f4000 (irq = 62) is a IMX
[ 1.022962] brd: module loaded
[ 1.027877] loop: module loaded
[ 1.031107] at24 2-0050: 256 byte at24 EEPROM, writable, 16 bytes/write
[ 1.038399] Loading iSCSI transport class v2.0-870.
[ 1.043540] iscsi: registered transport (tcp)
[ 1.048768] m25p80 spi0.0: found sst25vf016b, expected m25p80
[ 1.054610] m25p80 spi0.0: sst25vf016b (2048 Kbytes)
[ 1.059578] Creating 3 MTD partitions on "spi_flash":
[ 1.064646] 0x000000000000-0x0000000c0000 : "uboot"
[ 1.070502] 0x0000000c0000-0x000000100000 : "uboot environment"
[ 1.077194] 0x000000100000-0x000000200000 : "reserved"
[ 1.083519] No NAND device found.
[ 1.086843] Chip scan failed
[ 1.089798] GPMI NAND driver registered. (IMX)
[ 1.094740] FEC Ethernet Driver
[ 1.099962] fec_enet_mii_bus: probed
[ 1.104278] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.110940] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 1.117570] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 1.150425] fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
[ 1.170411] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 1.176524] hub 1-0:1.0: USB hub found
[ 1.180284] hub 1-0:1.0: 1 port detected
[ 1.184422] add wake up source irq 72
[ 1.188131] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[ 1.194774] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
[ 1.230424] fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
[ 1.250411] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[ 1.256455] hub 2-0:1.0: USB hub found
[ 1.260214] hub 2-0:1.0: 1 port detected
[ 1.264363] Initializing USB Mass Storage driver...
[ 1.269315] usbcore: registered new interface driver usb-storage
[ 1.275338] USB Mass Storage support registered.
[ 1.279957] ARC USBOTG Device Controller driver (1 August 2005)
[ 1.286561] mousedev: PS/2 mouse device common for all mice
[ 1.292323] =======snvs_pwrkey_probe() lp_cr 0x20
[ 1.297203] =======snvs_pwrkey_probe() lp_cr 0x20
[ 1.302234] input: snvs_power_key as /devices/virtual/input/input0
[ 1.308635] i.MX6 powerkey probe
[ 1.312101] i2c-core: driver [isl29023] using legacy suspend method
[ 1.318370] i2c-core: driver [isl29023] using legacy resume method
[ 1.324645] i2c /dev entries driver
[ 1.328984] at24 3-0050: 256 byte at24 EEPROM, writable, 16 bytes/write
[ 1.337793] CM-FX6: Detected SB-FX6m (Utilite) base board
[ 1.346564] rtc-em3027 3-0056: rtc core: registered rtc-em3027 as rtc0
[ 1.356844] iMX6 PCIe PCIe RC mode imx_pcie_pltfm_probe entering.
[ 1.470412] PCIE: imx_pcie_pltfm_probe start link up.
[ 1.580413] usb 2-1: new high speed USB device number 2 using fsl-ehci
[ 1.731858] hub 2-1:1.0: USB hub found
[ 1.735727] hub 2-1:1.0: 4 ports detected
[ 2.020493] usb 2-1.1: new low speed USB device number 3 using fsl-ehci
[ 2.090464] link up failed, DB_R0:0x00ee7700, DB_R1:0x08200000!
[ 2.096385] IMX PCIe port: link down!
[ 2.100089] i2c i2c-0: Added multiplexed i2c bus 3
[ 2.105172] i2c i2c-0: Added multiplexed i2c bus 4
[ 2.109967] gpio-i2cmux gpio-i2cmux: 2 port mux on imx-i2c adapter
[ 2.117102] lirc_dev: IR Remote Control driver registered, major 251
[ 2.123563] Linux video capture interface: v2.00
[ 2.128659] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
[ 2.136885] sdhci: Secure Digital Host Controller Interface driver
[ 2.143115] sdhci: Copyright(c) Pierre Ossman
[ 2.150779] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.0] using ADMA
[ 2.158136] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.2] using ADMA
[ 2.165784] VPU initialized
[ 2.169383] mxc_asrc registered
[ 2.176767] Galcore version 4.6.9.9754
[ 2.199648] Thermal calibration data is 0x57d5095f
[ 2.204500] Thermal sensor with ratio = 181
[ 2.230408] Anatop Thermal registered as thermal_zone0
[ 2.235660] anatop_thermal_probe: default cooling device is cpufreq!
[ 2.274487] usb 2-1.3: new low speed USB device number 4 using fsl-ehci
[ 2.385641] caam caam.0: device ID = 0x0a16010000000100
[ 2.392893] caam caam.0: job rings = 2, qi = 0
[ 2.397535] alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-caam)
[ 2.407763] caam caam.0: authenc-hmac-md5-cbc-aes-caam
[ 2.415066] alg: No test for authenc(hmac(sha1),cbc(aes)) (authenc-hmac-sha1-cbc-aes-caam)
[ 2.425435] caam caam.0: authenc-hmac-sha1-cbc-aes-caam
[ 2.433815] alg: No test for authenc(hmac(sha224),cbc(aes)) (authenc-hmac-sha224-cbc-aes-caam)
[ 2.442520] caam caam.0: authenc-hmac-sha224-cbc-aes-caam
[ 2.450502] alg: No test for authenc(hmac(sha256),cbc(aes)) (authenc-hmac-sha256-cbc-aes-caam)
[ 2.461479] caam caam.0: authenc-hmac-sha256-cbc-aes-caam
[ 2.468994] alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-hmac-md5-cbc-des3_ede-caam)
[ 2.480022] caam caam.0: authenc-hmac-md5-cbc-des3_ede-caam
[ 2.488767] alg: No test for authenc(hmac(sha1),cbc(des3_ede)) (authenc-hmac-sha1-cbc-des3_ede-caam)
[ 2.497932] caam caam.0: authenc-hmac-sha1-cbc-des3_ede-caam
[ 2.507726] alg: No test for authenc(hmac(sha224),cbc(des3_ede)) (authenc-hmac-sha224-cbc-des3_ede-caam)
[ 2.517236] caam caam.0: authenc-hmac-sha224-cbc-des3_ede-caam
[ 2.523169] alg: No test for authenc(hmac(sha256),cbc(des3_ede)) (authenc-hmac-sha256-cbc-des3_ede-caam)
[ 2.534703] caam caam.0: authenc-hmac-sha256-cbc-des3_ede-caam
[ 2.546660] alg: No test for authenc(hmac(md5),cbc(des)) (authenc-hmac-md5-cbc-des-caam)
[ 2.559880] caam caam.0: authenc-hmac-md5-cbc-des-caam
[ 2.567129] alg: No test for authenc(hmac(sha1),cbc(des)) (authenc-hmac-sha1-cbc-des-caam)
[ 2.577446] caam caam.0: authenc-hmac-sha1-cbc-des-caam
[ 2.584777] alg: No test for authenc(hmac(sha224),cbc(des)) (authenc-hmac-sha224-cbc-des-caam)
[ 2.595441] caam caam.0: authenc-hmac-sha224-cbc-des-caam
[ 2.603948] alg: No test for authenc(hmac(sha256),cbc(des)) (authenc-hmac-sha256-cbc-des-caam)
[ 2.612609] caam caam.0: authenc-hmac-sha256-cbc-des-caam
[ 2.620109] caam caam.0: cbc-aes-caam
[ 2.625892] caam caam.0: cbc-3des-caam
[ 2.631759] caam caam.0: cbc-des-caam
[ 2.797061] mmc1: host does not support reading read-only switch. assuming write-enable.
[ 2.818565] mmc1: new high speed SDHC card at address e624
[ 2.824333] mmcblk0: mmc1:e624 SS04G 3.69 GiB
[ 2.830138] mmcblk0: p1 p2
[ 2.869210] platform caam_jr.0: registering rng-caam
[ 2.876929] input: PixArt USB Optical Mouse as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.1/2-1.1:1.0/input/input1
[ 2.887835] generic-usb 0003:17EF:602E.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-fsl-ehci.1-1.1/input0
[ 2.903129] input: DELL Dell USB Entry Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.3/2-1.3:1.0/input/input2
[ 2.914281] generic-usb 0003:413C:2107.0002: input,hidraw1: USB HID v1.10 Keyboard [DELL Dell USB Entry Keyboard] on usb-fsl-ehci.1-1.3/input0
[ 2.927170] usbcore: registered new interface driver usbhid
[ 2.932757] usbhid: USB HID core driver
[ 2.937191] mxc_spdif mxc_spdif.0: MXC SPDIF Audio
[ 2.942815] _regulator_get: 2-001a supply AVDD not found, using dummy regulator
[ 2.950140] _regulator_get: 2-001a supply HPVDD not found, using dummy regulator
[ 2.957566] _regulator_get: 2-001a supply DCVDD not found, using dummy regulator
[ 2.964983] _regulator_get: 2-001a supply DBVDD not found, using dummy regulator
[ 2.973071] imx_wm8731_init: success
[ 2.977515] asoc: wm8731-hifi <-> imx-ssi.1 mapping ok
[ 2.984248] asoc: mxc-spdif <-> imx-spdif-dai.0 mapping ok
[ 2.990553] ALSA device list:
[ 2.993522] #0: wm8731-audio
[ 2.996576] #1: imx-spdif
[ 2.999600] NET: Registered protocol family 26
[ 3.004778] TCP cubic registered
[ 3.008010] NET: Registered protocol family 17
[ 3.012500] lib80211: common routines for IEEE802.11 drivers
[ 3.018187] Registering the dns_resolver key type
[ 3.023670] HDMI CEC initialized
[ 3.027348] mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
[ 3.034953] mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi
[ 3.041434] mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0x1a:0xa0:0xc1
[ 3.080461] imx-ipuv3 imx-ipuv3.0: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
[ 3.158568] Console: switching to colour frame buffer device 240x67
[ 3.198575] mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver dvi
[ 3.204966] _regulator_get: get() with no identifier
[ 3.218636] mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
[ 3.228943] asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok
[ 3.235656] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 3.243365] Registering SWP/SWPB emulation handler
[ 3.248455] Bus freq driver module loaded
[ 3.252485] Bus freq driver Enabled
[ 3.257664] mxc_dvfs_core_probe
[ 3.260946] DVFS driver module loaded
[ 3.265247] registered taskstats version 1
[ 3.269856] regulator_init_complete: ads7846_vcc: incomplete constraints, leaving on
[ 3.279055] rtc-em3027 3-0056: setting system clock to 2050-07-25 23:53:28 UTC (2542406008)
[ 3.295197] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[ 3.303963] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[ 4.694899] EXT4-fs (mmcblk0p2): recovery complete
[ 4.701457] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.709581] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 4.716555] devtmpfs: mounted
[ 4.719592] Freeing init memory: 248K

Welcome to Arch Linux ARM!

Expecting device dev-ttymxc3.device...
[ OK ] Reached target Remote File Systems.
Expecting device sys-subsystem-net-devices-eth0.device...
[ OK ] Reached target Encrypted Volumes.
[ OK ] Reached target Paths.
[ OK ] Set up automount Arbitrary Executable File Formats F...utomount Point.
[ OK ] Reached target Swap.
[ OK ] Created slice Root Slice.
[ OK ] Listening on Device-mapper event daemon FIFOs.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on Delayed Shutdown Socket.
[ OK ] Listening on LVM2 metadata daemon socket.
[ OK ] Listening on udev Kernel Socket.
[ OK ] Listening on udev Control Socket.
[ OK ] Created slice User and Session Slice.
[ OK ] Listening on Journal Socket.
[ OK ] Created slice System Slice.
Starting Remount Root and Kernel File Systems...
Mounting POSIX Message Queue File System...
Mounting Debug File System...
Starting Apply Kernel Variables...
Starting Setup Virtual Console...
Starting Create list of required static device nodes...rrent kernel...
Starting udev Coldplug all Devices...
[ OK ] Created slice system-netctl\x2difplugd.slice.
[ OK ] Created slice system-getty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
Starting Journal Service...
[ OK ] Started Journal Service.
[ OK ] Reached target Slices.
Mounting Temporary Directory...
[ 5.912648] systemd-journald[140]: Failed to register hostname fd in event loop: Operation not permitted. Ignoring.
Expecting device dev-mmcblk0p1.device...
[ OK ] Mounted Debug File System.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Temporary Directory.
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Setup Virtual Console.
[ OK ] Started Create list of required static device nodes ...current kernel.
Starting Create Static Device Nodes in /dev...
Starting Load/Save Random Seed...
[ OK ] Started Create Static Device Nodes in /dev.
[ OK ] Started Load/Save Random Seed.
Starting udev Kernel Device Manager...
[ OK ] Reached target Local File Systems (Pre).
[ OK [ 6.405407] systemd-udevd[148]: starting version 212
] Started udev Kernel Device Manager.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Found device /sys/subsystem/net/devices/eth0.
[ OK ] Found device /dev/ttymxc3.
[ OK ] Reached target Sound Card.
[ OK ] Found device /dev/mmcblk0p1.
Mounting /boot...
[ OK ] Mounted /boot.
[ OK ] Reached target Local File Systems.
Starting Create Volatile Files and Directories...
Starting Trigger Flushing of Journal to Persistent Storage...
[ OK ] Started Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Trigger Flushing of Journal to Persistent Storage.
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Timers.
[ OK ] Reached target Basic System.
Starting Automatic wired network connection using netctl profiles...
[ OK ] Started Automatic wired network connection using netctl profiles.
Starting OpenSSH Daemon...
[ OK ] Started OpenSSH Daemon.
Starting Entropy Harvesting Daemon...
Starting Login Service...
Starting D-Bus System Message Bus...
[ OK ] Started D-Bus System Message Bus.
Starting Permit User Sessions...

')

[joshbradfield]

Ran bad blocks on the SD card
$this->bbcode_second_pass_code('', '# badblocks -vw /dev/sdb')

Finished with 0 bad blocks found (0/0/0 errors) So looks like the card is fine...

[joshbradfield]

Put ubuntu on a sd card, (from the utilite webpage) booted with no issues...

[pepedog]

I don't have a value box, only a pro, so can't help, sorry