Odroid C2 - Black Screen on 4k TV

[mugnipper]

Hi,

I bought the C2 especially because of his capapilities of playing 4k videos, but after installing arch my screen just stays black (my tv says no signal) for the resolution 2160p60hz420.

My TV: GRUNDIG 65 VLO 9795 SP
Infos in english: https://www.displayspecifications.com/de/model/24cbd8a

My boot.ini:
$this->bbcode_second_pass_code('', '
ODROIDC2-UBOOT-CONFIG

# Possible screen resolutions
# Uncomment only a single Line! The line with setenv written.
# At least one mode must be selected.

# Custom modeline!
# To use custom modeline you need to disable all the below resolutions
# and setup your own!
# For more information check our wiki:
# http://odroid.com/dokuwiki/doku.php?id=en:c2_hdmi_autosetting
# Example below:
# setenv m "custombuilt"
# setenv modeline "1920,1200,154000,74040,60,1920,1968,2000,2080,1200,1202,1208,1235,1,0,1"

# Auto Detection of Monitor settings based on your Screen information
# See: http://odroid.com/dokuwiki/doku.php?id=en:c2_auto_detect_display
# setenv display_autodetect "true"

# 480 Lines (720x480)
# setenv m "480i60hz" # Interlaced 60Hz
# setenv m "480i_rpt" # Interlaced for Rear Projection Televisions 60Hz
# setenv m "480p60hz" # 480 Progressive 60Hz
# setenv m "480p_rpt" # 480 Progressive for Rear Projection Televisions 60Hz

# 576 Lines (720x576)
# setenv m "576i50hz" # Interlaced 50Hz
# setenv m "576i_rpt" # Interlaced for Rear Projection Televisions 50Hz
# setenv m "576p50hz" # Progressive 50Hz
# setenv m "576p_rpt" # Progressive for Rear Projection Televisions 50Hz

# 720 Lines (1280x720)
# setenv m "720p50hz" # 50Hz
# setenv m "720p60hz" # 60Hz

# 1080 Lines (1920x1080)
# setenv m "1080i60hz" # Interlaced 60Hz
# setenv m "1080p60hz"
# setenv m "1080i50hz" # Interlaced 50Hz
# setenv m "1080p50hz" # Progressive 50Hz
# setenv m "1080p24hz" # Progressive 24Hz

# 4K (3840x2160)
# setenv m "2160p30hz" # Progressive 30Hz
# setenv m "2160p25hz" # Progressive 25Hz
# setenv m "2160p24hz" # Progressive 24Hz
# setenv m "smpte24hz" # Progressive 24Hz SMPTE
# setenv m "2160p50hz" # Progressive 50Hz
# setenv m "2160p60hz" # Progressive 60Hz
# setenv m "2160p50hz420" # Progressive 50Hz with YCbCr 4:2:0 (Requires TV/Monitor that supports it)
setenv m "2160p60hz420" # Progressive 60Hz with YCbCr 4:2:0 (Requires TV/Monitor that supports it)

### VESA modes ###
# setenv m "640x480p60hz"
# setenv m "800x480p60hz"
# setenv m "480x800p60hz"
# setenv m "800x600p60hz"
# setenv m "1024x600p60hz"
# setenv m "1024x768p60hz"
# setenv m "1280x800p60hz"
# setenv m "1280x1024p60hz"
# setenv m "1360x768p60hz"
# setenv m "1440x900p60hz"
# setenv m "1600x900p60hz"
# setenv m "1680x1050p60hz"
# setenv m "1600x1200p60hz"
# setenv m "1920x1200p60hz"
# setenv m "2560x1080p60hz"
# setenv m "2560x1440p60hz"
# setenv m "2560x1600p60hz"
# setenv m "3440x1440p60hz"

# HDMI BPP Mode
setenv m_bpp "32"
# setenv m_bpp "24"
# setenv m_bpp "16"

# HDMI DVI/VGA modes
# By default its set to HDMI, if needed change below.
# Uncomment only a single Line.
# setenv vout "dvi"
# setenv vout "vga"
setenv vout "hdmi"

# HDMI HotPlug Detection control
# Allows you to force HDMI thinking that the cable is connected.
# true = HDMI will believe that cable is always connected
# false = will let board/monitor negotiate the connection status
setenv hpd "true"
# setenv hpd "false"

# Monitor output
# Controls if HDMI PHY should output anything to the monitor
setenv monitor_onoff "false" # true or false

# Server Mode (aka. No Graphics)
# Setting nographics to 1 will disable all video subsystem
# This mode is ideal of server type usage. (Saves ~300Mb of RAM)
setenv nographics "0"

# Meson Timer
# 1 - Meson Timer
# 0 - Arch Timer
# Using meson_timer improves the video playback however it breaks KVM (virtualization).
# Using arch timer allows KVM/Virtualization to work however you'll experience poor video
setenv mesontimer "1"

# UHS (Ultra High Speed) MicroSD mode enable/disable
setenv disableuhs "false"

# MicroSD Card Detection enable/disable
# Force the MMC controlled to believe that a card is connected.
setenv mmc_removable "true"

# USB Multi WebCam tweak
# Only enable this if you use it.
setenv usbmulticam "false"

# Disable/Enable ODROID-VU7 Touchscreen
setenv disable_vu7 "true"

# Default Console Device Setting
setenv condev "console=ttyS0,115200n8 console=tty0" # on both

# CPU Frequency / Cores control
###########################################
### WARNING!!! WARNING!!! WARNING!!!
# Before changing anything here please read the wiki entry:
# http://odroid.com/dokuwiki/doku.php?id=en:c2_set_cpu_freq
#
# MAX CPU's
# setenv maxcpus "1"
# setenv maxcpus "2"
# setenv maxcpus "3"
setenv maxcpus "4"

# MAX Frequency
# setenv max_freq "2016" # 2.016GHz
# setenv max_freq "1944" # 1.944GHz
# setenv max_freq "1944" # 1.944GHz
# setenv max_freq "1920" # 1.920GHz
# setenv max_freq "1896" # 1.896GHz
# setenv max_freq "1752" # 1.752GHz
# setenv max_freq "1680" # 1.680GHz
# setenv max_freq "1656" # 1.656GHz
setenv max_freq "1536" # 1.536GHz



###########################################

# Boot Arguments
if test "${display_autodetect}" = "true"; then usb pwren; hdmitx edid; fi
if test "${m}" = "custombuilt"; then setenv cmode "modeline=${modeline}"; fi
if test "${disable_vu7}" = "false"; then setenv hid_quirks "usbhid.quirks=0x0eef:0x0005:0x0004"; fi

setenv bootargs "root=/dev/mmcblk0p1 rootwait rw ${condev} no_console_suspend hdmimode=${m} ${cmode} m_bpp=${m_bpp} vout=${vout} fsck.repair=yes net.ifnames=0 elevator=noop disablehpd=${hpd} max_freq=${max_freq} maxcpus=${maxcpus} monitor_onoff=${monitor_onoff} disableuhs=${disableuhs} mmc_removable=${mmc_removable} usbmulticam=${usbmulticam} ${hid_quirks}"

# Booting

setenv loadaddr "0x11000000"
setenv dtb_loadaddr "0x1000000"
setenv initrd_loadaddr "0x13000000"

load mmc 0:1 ${loadaddr} /boot/Image
load mmc 0:1 ${dtb_loadaddr} /boot/dtbs/meson64_odroidc2.dtb

fdt addr ${dtb_loadaddr}
if test "${mesontimer}" = "0"; then fdt rm /meson_timer; fdt rm /cpus/cpu@0/timer; fdt rm /cpus/cpu@1/timer; fdt rm /cpus/cpu@2/timer; fdt rm /cpus/cpu@3/timer; fi
if test "${mesontimer}" = "1"; then fdt rm /timer; fi

if test "${nographics}" = "1"; then fdt rm /reserved-memory; fdt rm /aocec; fi
if test "${nographics}" = "1"; then fdt rm /meson-fb; fdt rm /amhdmitx; fdt rm /picdec; fdt rm /ppmgr; fi
if test "${nographics}" = "1"; then fdt rm /meson-vout; fdt rm /mesonstream; fdt rm /meson-fb; fi
if test "${nographics}" = "1"; then fdt rm /deinterlace; fdt rm /codec_mm; fi

load mmc 0:1 ${initrd_loadaddr} /boot/initramfs-linux.img

booti ${loadaddr} ${initrd_loadaddr}:${filesize} ${dtb_loadaddr}
')

2160p30Hz works as a resolution but looks a bit distorted.

I previously tried ubuntu there the setting ( setenv m "2160p60hz420") works in combination with commenting out auto_detection, I also tried 2160p60hz but that does not work on arch neither ubuntu.

Anyone an idea what is wrong or what I could try?

Thanks!