hai,
I have a problem in booting this DB-78200 i have burn uimage in nand flash its haging
as shown below
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-MV78200-A-BP LE
U-Boot 1.1.4 (Oct 26 2010 - 16:01:06) Marvell version: 3.3.30 - Dual CPU
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D4880
Soc: MV78200 A1 (DDR2)
CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 200Mhz
Enable 2T DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=5
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 64bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[32768kB@fe000000] [8192kB@fc000000] Flash: 40 MB
NAND:128 MB
CPU 0: ARM926 (Rev 0)
Streaming enabled
Write allocate disabled
FPU initialized to Run Fast Mode.
USB 0: host mode
USB 1: host mode
USB 2: device mode
PEX 4: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Relocate and enable second CPU
Hit any key to stop autoboot: 0
Using egiga0 device
TFTP from server 10.0.0.1; our IP address is 10.0.0.10
Filename 'uImage-2.6.22.18-ts-armv5l'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###################################
done
Bytes transferred = 2508460 (2646ac hex)
## Booting image at 02000000 ...
Image Name: Linux-2.6.22-ts-armv5l
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-MV78200-A-BP LE
U-Boot 1.1.4 (Oct 26 2010 - 16:01:06) Marvell version: 3.3.30 - Dual CPU
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D4880
Soc: MV78200 A1 (DDR2)
CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 200Mhz
Enable 2T DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=5
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 64bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
[32768kB@fe000000] [8192kB@fc000000] Flash: 40 MB
NAND:128 MB
CPU 0: ARM926 (Rev 0)
Streaming enabled
Write allocate disabled
FPU initialized to Run Fast Mode.
USB 0: host mode
USB 1: host mode
USB 2: device mode
PEX 4: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Relocate and enable second CPU
Hit any key to stop autoboot: 0
Using egiga0 device
TFTP from server 10.0.0.1; our IP address is 10.0.0.10
Filename 'uImage-2.6.22.18-ts-armv5l'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###################################
done
Bytes transferred = 2508460 (2646ac hex)
## Booting image at 02000000 ...
Image Name: Linux-2.6.22-ts-armv5l
Created: 2010-06-07 23:06:00 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2508396 Bytes = 2.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux.............................................................
................................................................................
.................. done, booting the kernel.
After this I burn the image file in nand flash
After this I rebooted the machine
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-MV78200-A-BP LE
U-Boot 1.1.4 (Oct 26 2010 - 15:59:57) Marvell version: 3.3.30
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D4880
Soc: MV78200 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 600Mhz
SysClock = 400Mhz , TClock = 200Mhz
Enable 2T
It struck at this state. pls help to reflash the nand flash procedure