Hi Elazar,
Bingo! THank you very much!!!
Booting succesfully!!
Solution for P24 -
$this->bbcode_second_pass_code('', '
drwxr-xr-x 2 root root 4096 2011-12-20 02:24 stage1
lrwxrwxrwx 1 root root 24 2012-01-16 21:38 stage1.wrapped -> stage1/stage1.wrapped700
drwxr-xr-x 2 root root 4096 2011-12-20 02:12 u-boot
lrwxrwxrwx 1 root root 21 2012-01-15 18:15 u-boot.wrapped -> u-boot/u-boot.wrapped
drwxr-xr-x 2 root root 4096 2011-12-20 02:26 uImages
lrwxrwxrwx 1 root root 20 2012-01-16 21:33 uImage -> uImages/uImage.nopci
')
For log :
user root
password root
Only question: why led is blinking? - OK Found: depmod -a
)) No question....
Regards,
Robert
$this->bbcode_second_pass_code('', 'Welcome to minicom 2.4
OPTIONS: I18n
Compiled on Jan 25 2010, 06:49:09.
Port /dev/ttyUSB0
Press CTRL-A Z for help on special keys
Stage-1 Bootloader Mon Nov 14 22:15:13 EST 2011
Attempting to set PLLA to 700MHz ...
plla_ctrl0 : 0x0000000A
plla_ctrl1 : 0x000E0000
plla_ctrl2 : 0x001B01A0
plla_ctrl3 : 0x00000016
PLLA Set
Setup memory, testing
Reading disk 0, Image 0
Sector : 0x0000009A
Hdr len: 0x0001FB34
Hdr CRC: 0x2229BDCD
OK
Initialising disks
SATA PHY not ready for device 1
Detecting SATA busses:
Bus 0: Found first device OK
Device 0: Model: WDC WD800BEAS-00RRT0 Firm: 04.01G04 Ser#: WD-WXE208C02426
Type: Hard Disk
Capacity: 76319.0 MB = 74.5 GB (156301488 x 512)
Device 1: not available
Failed to read valid environment from disk, using built-in default
U-Boot 1.1.2 (Dec 31 2011 - 15:24:45)
U-Boot code: 60E00000 -> 60E1FB34 BSS: -> 60E5435C
RAM Configuration:
Bank #0: 60000000 128 MB
SRAM Configuration:
64KB at 0x50000000
NAND:128 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Setting Linux mem= boot arg value
IDE read: device 0 block # 288, count 1 ... 1 blocks read: OK
Hit any key to stop autoboot: 0
Loading from IDE device 0, partition 1: Name: hda1
Type: U-Boot
Image Name: Linux-2.6.31.6_SMP_820
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2159884 Bytes = 2.1 MB
Load Address: 60008000
Entry Point: 60008000
## Booting image at 60500000 ...
Image Name: Linux-2.6.31.6_SMP_820
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2159884 Bytes = 2.1 MB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux................................................................................................................................... done,.
[ 0.000000] Linux version 2.6.31.6_SMP_820 (root@ProDev) (gcc version 4.6.0 20110429 (prerelease) (GCC) ) #100 SMP Sun May 29 04:53:45 EDT 2011
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Oxsemi NAS
[ 0.000000] 1 memory region
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: root=/dev/sda2 console=ttyS0,115200 elevator=cfq mac_adr=0x00,0x30,0xe0,0x00,0x00,0x01 rootwait ubi.mtd=2,512 mem=128M ps
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB = 128MB total
[ 0.000000] Memory: 125496KB available (3692K code, 291K data, 124K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:96
[ 0.000000] OX820_RPS_init_irq: interrupts 64 to 96
[ 0.010000] Console: colour dummy device 80x30
[ 0.010000] console [ttyS0] enabled
[ 0.020000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
[ 0.260000] Security Framework initialized
[ 0.260000] Mount-cache hash table entries: 512
[ 0.270000] CPU: Testing write buffer coherency: ok
[ 0.270000] Calibrating local timer... 349.99MHz.
[ 0.340000] CPU1: Booted secondary processor
[ 0.440000] Calibrating delay loop... 279.34 BogoMIPS (lpj=1396736)
[ 0.670000] Brought up 2 CPUs
[ 0.680000] SMP: Total of 2 processors activated (558.69 BogoMIPS).
[ 0.690000] NET: Registered protocol family 16
[ 0.690000] Number of DMA channels = 4, version = 4
[ 0.700000] Reserving a DMA channel for DirectRAID
[ 0.700000] Allocating 389 SRAM generic DMA descriptors
[ 0.720000] bio: create slab <bio-0> at 0
[ 0.730000] SCSI subsystem initialized
[ 0.730000] usbcore: registered new interface driver usbfs
[ 0.740000] usbcore: registered new interface driver hub
[ 0.740000] usbcore: registered new device driver usb
[ 0.780000] NET: Registered protocol family 2
[ 0.780000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.790000] Switched to NOHz mode on CPU #0
[ 0.790000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.790000] Switched to NOHz mode on CPU #1
[ 0.800000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.810000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.810000] TCP reno registered
[ 0.820000] NET: Registered protocol family 1
[ 0.820000] Create fragment cache
[ 0.830000] fuse init (API version 7.12)
[ 0.830000] msgmni has been set to 245
[ 0.840000] alg: No test for stdrng (krng)
[ 0.850000] io scheduler noop registered
[ 0.850000] io scheduler anticipatory registered
[ 0.850000] io scheduler deadline registered
[ 0.860000] io scheduler cfq registered (default)
[ 0.880000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.890000] serial8250: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[ 0.900000] brd: module loaded
[ 0.910000] loop: module loaded
[ 0.920000] ox820sata: OX820 sata core.
[ 0.920000] scsi0 : oxnassata
[ 0.920000] scsi1 : oxnassata
[ 0.930000] ata1: SATA max UDMA/133 irq 50
[ 0.930000] ata2: SATA max UDMA/133 irq 50
[ 0.940000] ox820sata: reseting SATA core
[ 1.460000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.520000] ata1.00: ATA-7: WDC WD800BEAS-00RRT0, 04.01G04, max UDMA/133
[ 1.520000] ata1.00: 156301488 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 1.530000] ata1.00: configured for UDMA/133
[ 1.540000] ox820sata: reseting SATA core
[ 2.250000] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.250000] scsi 0:0:0:0: Direct-Access ATA WDC WD800BEAS-00 04.0 PQ: 0 ANSI: 5
[ 2.260000] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 2.270000] sd 0:0:0:0: [sda] Write Protect is off
[ 2.270000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.280000] tun: Universal TUN/TAP device driver, 1.6
[ 2.280000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.280000] NAND: Page read time 40ms
[ 2.280000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[ 2.280000] Scanning device for bad blocks
[ 2.350000] sda:
[ 2.350000] Creating 2 MTD partitions on "NAND 128MiB 3,3V 8-bit":
[ 2.360000] 0x000000000000-0x000000e00000 : "boot"
[ 2.360000] 0x000000e00000-0x000008000000 : "rootfs"
[ 2.370000] UBI: attaching mtd2 to ubi0
[ 2.370000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 2.380000] UBI: logical eraseblock size: 129024 bytes
[ 2.380000] UBI: smallest flash I/O unit: 2048
[ 2.390000] UBI: sub-page size: 512
[ 2.390000] UBI: VID header offset: 512 (aligned 512)
[ 2.400000] UBI: data offset: 2048
[ 2.810000] sda1 sda2
[ 2.810000] UBI: attached mtd2 to ubi0
[ 2.820000] UBI: MTD device name: "rootfs"
[ 2.820000] UBI: MTD device size: 114 MiB
[ 2.830000] UBI: number of good PEBs: 912
[ 2.830000] UBI: number of bad PEBs: 0
[ 2.840000] UBI: max. allowed volumes: 128
[ 2.840000] UBI: wear-leveling threshold: 4096
[ 2.850000] UBI: number of internal volumes: 1
[ 2.850000] UBI: number of user volumes: 1
[ 2.860000] UBI: available PEBs: 0
[ 2.860000] UBI: total number of reserved PEBs: 912
[ 2.860000] UBI: number of PEBs reserved for bad PEB handling: 9
[ 2.870000] UBI: max/mean erase counter: 2/0
[ 2.880000] UBI: image sequence number: 0
[ 2.880000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.880000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.890000] oxnas-ehci oxnas-ehci.0: OXNAS EHCI Host Controller
[ 2.900000] oxnas-ehci oxnas-ehci.0: new USB bus registered, assigned bus number 1
[ 2.900000] UBI: background thread "ubi_bgt0d" started, PID 301
[ 2.930000] oxnas-ehci oxnas-ehci.0: irq 39, io mem 0x00000000
[ 2.950000] oxnas-ehci oxnas-ehci.0: USB 0.0 started, EHCI 1.00
[ 2.950000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.960000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.960000] usb usb1: Product: OXNAS EHCI Host Controller
[ 2.970000] usb usb1: Manufacturer: Linux 2.6.31.6_SMP_820 ehci_hcd
[ 2.980000] usb usb1: SerialNumber: usb
[ 2.980000] usb usb1: configuration #1 chosen from 1 choice
[ 2.990000] hub 1-0:1.0: USB hub found
[ 2.990000] hub 1-0:1.0: 2 ports detected
[ 3.000000] Initializing USB Mass Storage driver...
[ 3.000000] usbcore: registered new interface driver usb-storage
[ 3.010000] USB Mass Storage support registered.
[ 3.010000] mice: PS/2 mouse device common for all mice
[ 3.020000] TCP cubic registered
[ 3.020000] NET: Registered protocol family 10
[ 3.030000] NET: Registered protocol family 17
[ 3.030000] RPC: Registered udp transport module.
[ 3.040000] RPC: Registered tcp transport module.
[ 3.140000] kjournald starting. Commit interval 5 seconds
[ 3.140000] EXT3 FS on sda2, internal journal
[ 3.150000] EXT3-fs: mounted filesystem with writeback data mode.
[ 3.150000] VFS: Mounted root (ext3 filesystem) on device 8:2.
[ 3.160000] Freeing init memory: 124K
[ 3.310000] usb 1-1: new high speed USB device using oxnas-ehci and address 2
INIT: version 2.88 booting
[ 3.460000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 3.460000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 3.470000] usb 1-1: Product: USB2.0 Hub
[ 3.480000] usb 1-1: configuration #1 chosen from 1 choice
[ 3.480000] hub 1-1:1.0: USB hub found
[ 3.490000] hub 1-1:1.0: 4 ports detected
> Arch Linux ARM
> http://www.archlinuxarm.org
------------------------------
:: Mounting Root Read-Only [BUSY] [FAIL]
:: Adjusting system time and setting kernel timezone [BUSY] [DONE]
:: Starting UDev Daemon [BUSY] [DONE]
:: Triggering UDev uevents [BUSY] [DONE]
:: Loading Modules [BUSY] [ 5.450000] Probing for Synopsis GMAC, unit 0
[ 5.460000] eth0: Tuning GMAC 0 RGMII timings
[ 5.460000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
[ 5.470000] eth0: GMAC ver = 53, vendor ver = 18 at 0xed400000, IRQ 40
[ 5.470000] eth0: Found PHY at address 3, type 0x001cc914 -> 10/100/1000
[ 5.480000] eth0: Ethernet addr: 00:30:e0:00:00:00
[ 5.490000] probe() eth0: Leon x2 clock
[DONE]
:: Waiting for UDev uevents to be processed [BUSY] [ 6.400000] VFS: Can't find ext3 filesystem on dev sda1.
[ 6.400000] VFS: Can't find an ext2 filesystem on dev sda1.
[DONE]
:: Bringing up loopback interface [BUSY] [DONE]
:: Checking Filesystems [BUSY] [DONE]
:: Remounting Root Read/Write [BUSY] [FAIL]
:: Creating mtab [BUSY] [DONE]
:: Mounting Local Filesystems [BUSY] [DONE]
:: Activating Swap [BUSY] [DONE]
:: Configuring Time Zone [BUSY] [DONE]
:: Removing Leftover Files [BUSY] [DONE]
:: Setting Hostname: alarm [BUSY] [DONE]
:: Setting Locale: en_US.UTF-8 [BUSY] [DONE]
:: Setting Consoles to UTF-8 mode [BUSY] [DONE]
:: Loading Keyboard Map: us [BUSY] [DONE]
:: Saving dmesg Log [BUSY] [DONE]
INIT: Entering runlevel: 3
:: Setting MAC address [BUSY] FATAL: Module oxnas_led not found.
AMBER
GREEN
[ 9.560000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
[ 9.570000] CoPro offload is active on eth0
[ 9.570000] Alloc'ing ARM descs 8192 bytes
[ 9.580000] Alloc'ing CoPro parameters 36 bytes
[ 9.580000] gmac gmac.0: firmware: requesting gmac_copro_firmware
[ 9.630000] CoPro: Programming start address as 0xd000e000
[ 9.740000] eth0: Resetting GMAC
[ 9.740000] eth0: GMAC reset complete
[ 9.750000] eth0: Setting Rx flow control thresholds for LAN port
[ 10.300000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
[ 10.800000] eth0: link down
[ 12.760000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[DONE]
[ 12.800000] eth0: link up, 100Mbps, full-duplex, using pause, lpa 0x45E1
[ 12.800000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
:: Starting Syslog-NG [BUSY] [DONE]
:: Starting Network [BUSY] [DONE]
:: Mounting Network Filesystems [BUSY] [DONE]
:: Starting crond daemon [BUSY] [DONE]
:: Starting Secure Shell Daemon [BUSY] ssh-keygen: generating new host keys: RSA1 RSA DSA ECDSA
[DONE]
:: Starting OpenNTPD [BUSY] [DONE]
Arch Linux 2.6.31.6_SMP_820 (alarm) (ttyS0)
alarm login: root
Password:
Login incorrect
alarm login:
Login timed out after 60 seconds.
Arch Linux 2.6.31.6_SMP_820 (alarm) (ttyS0)
alarm login:')