Can update for linux-3.2.1-iconnect not loading any modules

[lulo]

$this->bbcode_second_pass_code('', '[lulo@lulo-iconnect ~]$ sudo pacman -Syu
:: Synchronizowanie baz danych z pakietami...
core 38,0 KiB 345K/s 00:00 [#############################################] 100%
extra 422,9 KiB 1880K/s 00:00 [#############################################] 100%
community 369,5 KiB 4,43M/s 00:00 [#############################################] 100%
aur 9,6 KiB 8,70M/s 00:00 [#############################################] 100%
:: Rozpoczynanie pełnej aktualizacji systemu...
ostrzeżenie: libtorrent: local (0.12.9-1.with.pre.allocate) jest nowsze niż community (0.12.9-1)
:: Zastąpić module-init-tools przez core/kmod? [T/n]
ostrzeżenie: rtorrent: local (0.8.9-2.with.color.support) jest nowsze niż community (0.8.9-2)
rozwiązywanie zależności...
szukanie konfliktów międzypakietowych...

Cele (16): freeglut-2.8.0-1 gnutls-3.0.12-1 initscripts-2012.01.3-1 iproute2-3.2.0-2 iptraf-ng-1.1.0-1 kmod-4-1 linux-3.2.1-1
linux-headers-3.2.1-1 mdadm-3.2.3-1 mkinitcpio-0.8.2-1 module-init-tools-3.16-3 [removal] perl-libwww-6.03-2
sdl-1.2.15-1 sdl_image-1.2.12-1 sqlite3-3.7.10-1 udev-178-1

Całkowity rozmiar do pobrania: 21,07 MiB
Całkowity rozmiar po instalacji: 72,54 MiB
Rozmiar netto aktualizacji: 0,31 MiB

Kontynuować instalację? [T/n]
:: Pobieranie pakietów z core...
kmod-4-1-arm 67,8 KiB 458K/s 00:00 [#############################################] 100%
udev-178-1-arm 191,6 KiB 1628K/s 00:00 [#############################################] 100%
iproute2-3.2.0-2-arm 371,2 KiB 3,04M/s 00:00 [#############################################] 100%
initscripts-2012.01.3-1-any 26,2 KiB 12,2M/s 00:00 [#############################################] 100%
mkinitcpio-0.8.2-1-any 21,8 KiB 9,82M/s 00:00 [#############################################] 100%
linux-3.2.1-1-arm 13,5 MiB 4,87M/s 00:03 [#############################################] 100%
linux-headers-3.2.1-1-arm 4,4 MiB 4,88M/s 00:01 [#############################################] 100%
mdadm-3.2.3-1-arm 244,3 KiB 5,45M/s 00:00 [#############################################] 100%
sqlite3-3.7.10-1-arm 332,4 KiB 6,17M/s 00:00 [#############################################] 100%
:: Pobieranie pakietów z extra...
freeglut-2.8.0-1-arm 63,8 KiB 11,2M/s 00:00 [#############################################] 100%
gnutls-3.0.12-1-arm 1378,9 KiB 4,89M/s 00:00 [#############################################] 100%
iptraf-ng-1.1.0-1-arm 65,2 KiB 11,3M/s 00:00 [#############################################] 100%
perl-libwww-6.03-2-any 126,4 KiB 2,10M/s 00:00 [#############################################] 100%
sdl-1.2.15-1-arm 299,1 KiB 5,97M/s 00:00 [#############################################] 100%
sdl_image-1.2.12-1-arm 20,6 KiB 11,2M/s 00:00 [#############################################] 100%
(15/15) sprawdzanie spójności pakietów [#############################################] 100%
(15/15) wczytywanie plików pakietu [#############################################] 100%
(15/15) sprawdzanie konfliktów plików [#############################################] 100%
błąd: nie udało się dokonać transakcji (konfliktujące pliki)
initscripts: /etc/profile.d/locale.sh znajduje się w systemie plików
Wystąpiły błędy, nie zaktualizowano żadnego pakietu.
[lulo@lulo-iconnect ~]$ sudo pacman -Syu --force
:: Synchronizowanie baz danych z pakietami...
core jest już w najnowszej wersji
extra jest już w najnowszej wersji
community jest już w najnowszej wersji
aur jest już w najnowszej wersji
:: Rozpoczynanie pełnej aktualizacji systemu...
ostrzeżenie: libtorrent: local (0.12.9-1.with.pre.allocate) jest nowsze niż community (0.12.9-1)
:: Zastąpić module-init-tools przez core/kmod? [T/n]
ostrzeżenie: rtorrent: local (0.8.9-2.with.color.support) jest nowsze niż community (0.8.9-2)
rozwiązywanie zależności...
szukanie konfliktów międzypakietowych...

Cele (16): freeglut-2.8.0-1 gnutls-3.0.12-1 initscripts-2012.01.3-1 iproute2-3.2.0-2 iptraf-ng-1.1.0-1 kmod-4-1 linux-3.2.1-1
linux-headers-3.2.1-1 mdadm-3.2.3-1 mkinitcpio-0.8.2-1 module-init-tools-3.16-3 [removal] perl-libwww-6.03-2
sdl-1.2.15-1 sdl_image-1.2.12-1 sqlite3-3.7.10-1 udev-178-1

Całkowity rozmiar po instalacji: 72,54 MiB
Rozmiar netto aktualizacji: 0,31 MiB

Kontynuować instalację? [T/n]
(15/15) sprawdzanie spójności pakietów [#############################################] 100%
(15/15) wczytywanie plików pakietu [#############################################] 100%
(16/16) sprawdzanie dostępnego miejsca na dysku [#############################################] 100%
(1/1) usuwanie module-init-tools [#############################################] 100%
( 1/15) aktualizowanie freeglut [#############################################] 100%
( 2/15) aktualizowanie gnutls [#############################################] 100%
( 3/15) instalowanie kmod [#############################################] 100%
( 4/15) aktualizowanie udev [#############################################] 100%
( 5/15) aktualizowanie iproute2 [#############################################] 100%
( 6/15) aktualizowanie initscripts [#############################################] 100%
If using non-bash-compatible shell, please set LANG in /etc/locale.conf,
as LOCALE in /etc/rc.conf no longer works.
( 7/15) aktualizowanie iptraf-ng [#############################################] 100%
( 8/15) aktualizowanie mkinitcpio [#############################################] 100%
( 9/15) aktualizowanie linux [#############################################] 100%
>>> Updating module dependencies. Please wait ...
(10/15) aktualizowanie linux-headers [#############################################] 100%
(11/15) aktualizowanie mdadm [#############################################] 100%
(12/15) aktualizowanie perl-libwww [#############################################] 100%
(13/15) aktualizowanie sdl [#############################################] 100%
(14/15) aktualizowanie sdl_image [#############################################] 100%
(15/15) aktualizowanie sqlite3 [#############################################] 100%
[lulo@lulo-iconnect ~]$ sudo reboot && exit
The system is going down for reboot NOW!t (pts/0) (Thu Jan 26 16:17:25 2012):
logout
Connection to lulo-iconnect.org closed.
slawomir@lulojs-ubuntu:~$ ssh lulo@lulo-iconnect.org
ssh: connect to host lulo-iconnect.org port 22: No route to host
slawomir@lulojs-ubuntu:~$ ssh lulo@lulo-iconnect.org
ssh: connect to host lulo-iconnect.org port 22: No route to host
slawomir@lulojs-ubuntu:~$ ssh lulo@lulo-iconnect.org
ssh: connect to host lulo-iconnect.org port 22: No route to host
slawomir@lulojs-ubuntu:~$ ssh lulo@lulo-iconnect.org
lulo@lulo-iconnect.org's password:
Last login: Thu Jan 26 15:35:36 2012 from lulojs-ubuntu.org
[lulo@lulo-iconnect ~]$ dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.1-1-ARCH (root@platinum) (gcc version 4.6.2 20111223 (prerelease) (GCC) ) #1 PREEMPT Sun Jan 22 07:37:31 UTC 2012
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Iomega iConnect Wireless
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat c05cd2f8, node_mem_map c069e000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] allocated 1048576 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 252060k/252060k available, 10084k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xfe800000 ( 736 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc056986c (5511 kB)
[ 0.000000] .init : 0xc056a000 - 0xc0596000 ( 176 kB)
[ 0.000000] .data : 0xc0596000 - 0xc05d0078 ( 233 kB)
[ 0.000000] .bss : 0xc05d009c - 0xc069ddb4 ( 824 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 0.000000] Console: colour dummy device 80x30
[ 17.634535] Calibrating delay loop... 990.41 BogoMIPS (lpj=4952064)
[ 17.674443] pid_max: default: 32768 minimum: 301
[ 17.674589] Security Framework initialized
[ 17.674616] AppArmor: AppArmor disabled by boot time parameter
[ 17.674696] Mount-cache hash table entries: 512
[ 17.675152] Initializing cgroup subsys cpuacct
[ 17.675183] Initializing cgroup subsys memory
[ 17.675226] Initializing cgroup subsys devices
[ 17.675240] Initializing cgroup subsys freezer
[ 17.675251] Initializing cgroup subsys blkio
[ 17.675278] Initializing cgroup subsys perf_event
[ 17.675372] CPU: Testing write buffer coherency: ok
[ 17.676797] devtmpfs: initialized
[ 17.678904] NET: Registered protocol family 16
[ 17.679768] Kirkwood: MV88F6281-A0, TCLK=200000000.
[ 17.679784] Feroceon L2: Enabling L2
[ 17.679829] Feroceon L2: Cache support initialised.
[ 17.680516] initial MPP regs: 21111111 00003311 33331100 33333333 00000333 00000000 00000000
[ 17.680551] final MPP regs: 21111111 00003311 33331100 33333333 00000333 00000000 00000000
[ 17.681307] Kirkwood PCIe port 0:
[ 17.681316] link up
[ 17.681326] PCI: bus0 uses PCIe port 0
[ 17.681495] pci 0000:00:00.0: [11ab:6281] type 0 class 0x000580
[ 17.681528] pci 0000:00:00.0: reg 10: [mem 0xf1000000-0xf10fffff 64bit pref]
[ 17.681548] pci 0000:00:00.0: reg 18: [mem 0x00000000-0x0fffffff]
[ 17.681598] pci 0000:00:00.0: supports D1 D2
[ 17.681646] pci 0000:00:01.0: [1814:3090] type 0 class 0x000280
[ 17.681674] pci 0000:00:01.0: reg 10: [mem 0x40000000-0x4000ffff]
[ 17.681813] PCI: bus0: Fast back to back transfers disabled
[ 17.682114] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff]
[ 17.682137] pci 0000:00:01.0: BAR 0: set to [mem 0xe0000000-0xe000ffff] (PCI address [0xe0000000-0xe000ffff])
[ 17.688131] bio: create slab <bio-0> at 0
[ 17.688592] vgaarb: loaded
[ 17.688923] SCSI subsystem initialized
[ 17.689103] libata version 3.00 loaded.
[ 17.689368] usbcore: registered new interface driver usbfs
[ 17.689493] usbcore: registered new interface driver hub
[ 17.689626] usbcore: registered new device driver usb
[ 17.690332] Switching to clocksource orion_clocksource
[ 17.704052] FS-Cache: Loaded
[ 17.716019] NET: Registered protocol family 2
[ 17.716297] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 17.717097] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 17.717319] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 17.717434] TCP: Hash tables configured (established 8192 bind 8192)
[ 17.717446] TCP reno registered
[ 17.717460] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 17.717487] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 17.717767] NET: Registered protocol family 1
[ 17.717831] PCI: CLS 32 bytes, default 32
[ 17.718527] audit: initializing netlink socket (disabled)
[ 17.718569] type=2000 audit(0.070:1): initialized
[ 17.821360] VFS: Disk quotas dquot_6.5.2
[ 17.821666] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 17.824391] JFFS2 version 2.2. (NAND) \xffffffc2\xffffffa9\xffffffa9 2001-2006 Red Hat, Inc.
[ 17.825716] aufs 3.2-20120109
[ 17.825742] msgmni has been set to 492
[ 17.827317] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 17.827335] io scheduler noop registered
[ 17.827345] io scheduler deadline registered
[ 17.827391] io scheduler cfq registered (default)
[ 17.827497] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 17.827538] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 17.860416] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 17.900422] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 17.940421] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 17.980420] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 17.985822] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 18.006509] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 18.006627] console [ttyS0] enabled
[ 18.014306] brd: module loaded
[ 18.018090] loop: module loaded
[ 18.019215] ONFI flash detected
[ 18.019392] NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
[ 18.019420] Scanning device for bad blocks
[ 18.261330] Creating 4 MTD partitions on "orion_nand":
[ 18.261353] 0x000000000000-0x000000100000 : "u-boot"
[ 18.262496] 0x000000100000-0x000000400000 : "uImage"
[ 18.263552] 0x000000400000-0x000002400000 : "rootfs"
[ 18.264522] 0x000002400000-0x000020000000 : "data"
[ 18.266759] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 18.266883] mv643xx_eth smi: probed
[ 18.269146] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address xx:xx:xx:xx:xx:xx
[ 18.269295] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 18.269355] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 18.269458] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 18.290398] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 18.310384] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 18.311074] hub 1-0:1.0: USB hub found
[ 18.311101] hub 1-0:1.0: 1 port detected
[ 18.311758] Initializing USB Mass Storage driver...
[ 18.311875] usbcore: registered new interface driver usb-storage
[ 18.311886] USB Mass Storage support registered.
[ 18.312006] usbcore: registered new interface driver libusual
[ 18.312361] mousedev: PS/2 mouse device common for all mice
[ 18.312666] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 18.312845] sdhci: Secure Digital Host Controller Interface driver
[ 18.312857] sdhci: Copyright(c) Pierre Ossman
[ 18.312944] sdhci-pltfm: SDHCI platform and OF driver helper
[ 18.313136] Registered led device: iconnect:led_level
[ 18.313271] Registered led device: iconnect:blue:power
[ 18.313394] Registered led device: iconnect:red:power
[ 18.313517] Registered led device: iconnect:blue:usb1
[ 18.313653] Registered led device: iconnect:blue:usb2
[ 18.313779] Registered led device: iconnect:blue:usb3
[ 18.313906] Registered led device: iconnect:blue:usb4
[ 18.314038] Registered led device: iconnect:blue:otb
[ 18.314309] usbcore: registered new interface driver r8712u
[ 18.315234] GRE over IPv4 demultiplexor driver
[ 18.315399] TCP cubic registered
[ 18.315412] NET: Registered protocol family 17
[ 18.315510] lib80211: common routines for IEEE802.11 drivers
[ 18.315523] lib80211_crypt: registered algorithm 'NULL'
[ 18.315533] Registering the dns_resolver key type
[ 18.315583] Gating clock of unused units
[ 18.315594] before: 0x00dfc3dd
[ 18.315603] after: 0x00c701cd
[ 18.316206] registered taskstats version 1
[ 18.317030] console [netcon0] enabled
[ 18.317040] netconsole: network logging started
[ 18.317632] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 18.317928] rtc-mv rtc-mv: setting system clock to 2012-01-26 15:14:11 UTC (1327590851)
[ 18.318232] Waiting 10sec before mounting root device...
[ 18.630390] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 18.781471] hub 1-1:1.0: USB hub found
[ 18.781565] hub 1-1:1.0: 4 ports detected
[ 19.060438] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[ 19.172743] scsi0 : usb-storage 1-1.1:1.0
[ 20.171179] scsi 0:0:0:0: Direct-Access ST925031 5AS PQ: 0 ANSI: 2 CCS
[ 20.172273] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 20.172529] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 20.172986] sd 0:0:0:0: [sda] Write Protect is off
[ 20.173003] sd 0:0:0:0: [sda] Mode Sense: 00 38 00 00
[ 20.173475] sd 0:0:0:0: [sda] Asking for cache data failed
[ 20.178996] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 20.187838] sd 0:0:0:0: [sda] Asking for cache data failed
[ 20.193403] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 20.263312] sda: sda1
[ 20.265587] sd 0:0:0:0: [sda] Asking for cache data failed
[ 20.271140] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 20.277262] sd 0:0:0:0: [sda] Attached SCSI disk
[ 28.437676] EXT3-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
[ 28.438169] kjournald starting. Commit interval 5 seconds
[ 28.438741] EXT3-fs (sda1): using internal journal
[ 28.438762] EXT3-fs (sda1): mounted filesystem with writeback data mode
[ 28.438808] VFS: Mounted root (ext3 filesystem) on device 8:1.
[ 28.454886] devtmpfs: mounted
[ 28.455538] Freeing init memory: 176K
[ 31.563755] udevd[87]: starting version 178
[ 32.325242] rt2800pci: Unknown symbol rt2x00mac_sw_scan_complete (err 0)
[ 32.325263] rt2800pci: Unknown symbol rt2800_config_shared_key (err 0)
[ 32.325277] rt2800pci: Unknown symbol rt2x00mac_add_interface (err 0)
[ 32.325290] rt2800pci: Unknown symbol rt2800_enable_radio (err 0)
[ 32.325303] rt2800pci: Unknown symbol rt2800_reset_tuner (err 0)
[ 32.325316] rt2800pci: Unknown symbol rt2x00mac_get_stats (err 0)
[ 32.325329] rt2800pci: Unknown symbol rt2x00mac_sta_remove (err 0)
[ 32.325342] rt2800pci: Unknown symbol rt2800_validate_eeprom (err 0)
[ 32.325373] rt2800pci: Unknown symbol rt2x00pci_flush_queue (err 0)
[ 32.325386] rt2800pci: Unknown symbol rt2800_link_stats (err 0)
[ 32.325406] rt2800pci: Unknown symbol rt2800_rfkill_poll (err 0)
[ 32.325419] rt2800pci: Unknown symbol rt2800_txdone_entry (err 0)
[ 32.325432] rt2800pci: Unknown symbol rt2800_probe_hw_mode (err 0)
[ 32.325445] rt2800pci: Unknown symbol rt2800_read_eeprom_efuse (err 0)
[ 32.325459] rt2800pci: Unknown symbol rt2x00pci_initialize (err 0)
[ 32.325472] rt2800pci: Unknown symbol rt2x00mac_set_key (err 0)
[ 32.325485] rt2800pci: Unknown symbol rt2800_efuse_detect (err 0)
[ 32.325498] rt2800pci: Unknown symbol rt2800_config_filter (err 0)
[ 32.325511] rt2800pci: Unknown symbol rt2800_conf_tx (err 0)
[ 32.325524] rt2800pci: Unknown symbol rt2x00mac_sw_scan_start (err 0)
[ 32.325537] rt2800pci: Unknown symbol rt2x00mac_tx_frames_pending (err 0)
[ 32.325551] rt2800pci: Unknown symbol rt2800_check_firmware (err 0)
[ 32.325564] rt2800pci: Unknown symbol rt2800_mcu_request (err 0)
[ 32.325584] rt2800pci: Unknown symbol rt2800_init_eeprom (err 0)
[ 32.325597] rt2800pci: Unknown symbol rt2800_config_pairwise_key (err 0)
[ 32.325611] rt2800pci: Unknown symbol rt2x00pci_uninitialize (err 0)
[ 32.325624] rt2800pci: Unknown symbol rt2x00queue_get_entry (err 0)
[ 32.325637] rt2800pci: Unknown symbol rt2x00pci_suspend (err 0)
[ 32.325657] rt2800pci: Unknown symbol rt2800_clear_beacon (err 0)
[ 32.325679] rt2800pci: Unknown symbol rt2800_get_tsf (err 0)
[ 32.325692] rt2800pci: Unknown symbol rt2x00pci_remove (err 0)
[ 32.325705] rt2800pci: Unknown symbol rt2x00mac_remove_interface (err 0)
[ 32.325726] rt2800pci: Unknown symbol rt2800_load_firmware (err 0)
[ 32.325739] rt2800pci: Unknown symbol rt2x00mac_config (err 0)
[ 32.325769] rt2800pci: Unknown symbol eeprom_93cx6_multiread (err 0)
[ 32.325782] rt2800pci: Unknown symbol rt2x00mac_start (err 0)
[ 32.325795] rt2800pci: Unknown symbol rt2x00mac_rfkill_poll (err 0)
[ 32.325808] rt2800pci: Unknown symbol rt2800_process_rxwi (err 0)
[ 32.325821] rt2800pci: Unknown symbol rt2x00mac_stop (err 0)
[ 32.325834] rt2800pci: Unknown symbol rt2800_link_tuner (err 0)
[ 32.325852] rt2800pci: Unknown symbol rt2x00pci_regbusy_read (err 0)
[ 32.325865] rt2800pci: Unknown symbol rt2800_config_intf (err 0)
[ 32.325878] rt2800pci: Unknown symbol rt2800_set_rts_threshold (err 0)
[ 32.325892] rt2800pci: Unknown symbol rt2800_wait_wpdma_ready (err 0)
[ 32.325911] rt2800pci: Unknown symbol rt2x00mac_configure_filter (err 0)
[ 32.325925] rt2800pci: Unknown symbol rt2800_sta_remove (err 0)
[ 32.325938] rt2800pci: Unknown symbol rt2x00mac_flush (err 0)
[ 32.325951] rt2800pci: Unknown symbol rt2x00lib_pretbtt (err 0)
[ 32.325964] rt2800pci: Unknown symbol rt2800_get_tkip_seq (err 0)
[ 32.325977] rt2800pci: Unknown symbol rt2800_write_tx_data (err 0)
[ 32.325990] rt2800pci: Unknown symbol rt2800_disable_radio (err 0)
[ 32.326003] rt2800pci: Unknown symbol rt2800_ampdu_action (err 0)
[ 32.326016] rt2800pci: Unknown symbol rt2800_config_ant (err 0)
[ 32.326029] rt2800pci: Unknown symbol rt2x00mac_tx (err 0)
[ 32.326042] rt2800pci: Unknown symbol rt2800_sta_add (err 0)
[ 32.326054] rt2800pci: Unknown symbol rt2x00pci_resume (err 0)
[ 32.326068] rt2800pci: Unknown symbol rt2x00mac_sta_add (err 0)
[ 32.326084] rt2800pci: Unknown symbol rt2800_config (err 0)
[ 32.326102] rt2800pci: Unknown symbol rt2x00pci_probe (err 0)
[ 32.326126] rt2800pci: Unknown symbol rt2800_write_beacon (err 0)
[ 32.326139] rt2800pci: Unknown symbol rt2800_gain_calibration (err 0)
[ 32.326159] rt2800pci: Unknown symbol rt2800_get_survey (err 0)
[ 32.326172] rt2800pci: Unknown symbol rt2x00pci_rxdone (err 0)
[ 32.326185] rt2800pci: Unknown symbol rt2x00lib_beacondone (err 0)
[ 32.326202] rt2800pci: Unknown symbol rt2800_config_erp (err 0)
[ 32.326215] rt2800pci: Unknown symbol rt2x00mac_get_ringparam (err 0)
[ 32.326229] rt2800pci: Unknown symbol rt2x00mac_bss_info_changed (err 0)
[ 33.343955] EXT3-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
[ 33.345395] EXT3-fs (sda1): using internal journal
[ 34.274124] Adding 524284k swap on /swapfile.img. Priority:-1 extents:133 across:541292k
[ 41.422690] mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 49.597008] NET: Registered protocol family 10
[ 52.549414] i2c_mv64xxx: Unknown symbol i2c_add_numbered_adapter (err 0)
[ 52.549436] i2c_mv64xxx: Unknown symbol i2c_del_adapter (err 0)
[ 52.653412] lm63: Unknown symbol hwmon_device_register (err 0)
[ 52.653462] lm63: Unknown symbol i2c_register_driver (err 0)
[ 52.653522] lm63: Unknown symbol hwmon_device_unregister (err 0)
[ 52.653537] lm63: Unknown symbol i2c_smbus_write_byte_data (err 0)
[ 52.653552] lm63: Unknown symbol i2c_del_driver (err 0)
[ 52.653571] lm63: Unknown symbol i2c_smbus_read_byte_data (err 0)
[ 54.755780] bridge: Unknown symbol llc_mac_hdr_init (err 0)
[ 54.755872] bridge: Unknown symbol stp_proto_register (err 0)
[ 54.756136] bridge: Unknown symbol stp_proto_unregister (err 0)
[ 54.772185] bridge: Unknown symbol llc_mac_hdr_init (err 0)
[ 54.772277] bridge: Unknown symbol stp_proto_register (err 0)
[ 54.772539] bridge: Unknown symbol stp_proto_unregister (err 0)
[ 54.782167] device eth0 entered promiscuous mode
[ 382.442799] mv643xx_eth_port mv643xx_eth_port.0: eth0: link down
[ 399.213711] mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 399.213886] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 409.520363] eth0: no IPv6 routers present
[lulo@lulo-iconnect ~]$ lsmod
Module Size Used by
ipv6 254908 10
mv_cesa 9269 0
[lulo@lulo-iconnect ~]$ sudo modprobe lm63
Hasło:
[lulo@lulo-iconnect ~]$ lsmod
Module Size Used by
ipv6 254908 10
mv_cesa 9269 0
[lulo@lulo-iconnect ~]$ sudo modprobe lm63 -v
insmod /lib/modules/3.2.1-1-ARCH/kernel/drivers/hwmon/lm63.ko.gz
[lulo@lulo-iconnect ~]$ lsmod
Module Size Used by
ipv6 254908 10
mv_cesa 9269 0
[lulo@lulo-iconnect ~]$ cd /lib/modules/3.2.1-1-ARCH/kernel/drivers/hwmon
[lulo@lulo-iconnect hwmon]$ ls
hwmon.ko.gz lm63.ko.gz lm75.ko.gz lm77.ko.gz lm90.ko.gz
[lulo@lulo-iconnect hwmon]$ insmod lm63.ko.gz
Error: could not insert module lm63.ko.gz: Operation not permitted
[lulo@lulo-iconnect hwmon]$ insmod lm63.ko
Error: could not load module lm63.ko: No such file or directory
[lulo@lulo-iconnect hwmon]$ insmod lm63*
Error: could not insert module lm63.ko.gz: Operation not permitted
')

very,very,very....nice...cant load any modules (modprobe and/or insmod)...kmod-4.1 install...module-init-tools remove...system bad funcional...tragedy !!!

Any ideas ?

[kmihelich]

Yeah, 3.2.1 has proven to be a complete trainwreck. I'll be moving the kernel back to 3.1 this weekend.

[lulo]

ok...thank you k.