I am learning kernel hacking recenly.
And in the progress, porting latest linux kernel (v3.11.1) & u-boot (2013.07) to pogoplug v3,
I have tried hard to fit all existing code into latest framework, to make it maintainable.
And dropped some messy code if better alternative available (GMAC => STMMAC)
It is not thoroughly tested, but works reasonably stable.
Is anyone willing to work with me test and stablize it, and finally make it available to the community?
Below is the bootlog
$this->bbcode_second_pass_code('', 'U-Boot SPL 2013.07 (Sep 23 2013 - 23:13:54)
Boot device: SATA
Attempting to set PLLA to 800 MHz ...
plla_ctrl0 : 0000030a
plla_ctrl1 : 00400000
plla_ctrl2 : 007f0068
plla_ctrl3 : 00000193
PLLA Set
Bus 0: OK
Device 0:
U-Boot 2013.07 (Sep 23 2013 - 23:13:54) for OXNAS
DRAM: 128 MiB
IDE: Bus 0: OK
Device 0: Model: ST3120827AS Firm: 3.42 Ser#: XXXXXXXXXX
Type: Hard Disk
Supports 48-bit addressing
Capacity: 114473.4 MB = 111.7 GB (234441648 x 512)
NAND: 128 MiB
reading u-boot.env
In: serial
Out: serial
Err: serial
Net: mii0
Hit any key to stop autoboot: 0
reading uImage
3438480 bytes read in 783 ms (4.2 MiB/s)
reading ox820.dtb
5934 bytes read in 13 ms (445.3 KiB/s)
## Booting kernel from Legacy Image at 60000000 ...
Image Name: Linux-3.11.1+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3438416 Bytes = 3.3 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 61000000
Booting using the fdt blob at 0x61000000
Loading Kernel Image ... OK
Loading Device Tree to 67e28000, end 67e2c72d ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.11.1+ (mahaijun@ubuntu) (gcc version 4.7.3 (Ubuntu/Linaro 4.7.3-1ubuntu1) ) #827 SMP Mon Sep 23 22:4
2:59 CST 2013
[ 0.000000] CPU: ARMv6-compatible processor [410fb025] revision 5 (ARMv7), cr=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: PLXTECH NAS782X SoC (Flattened Device Tree), model: plxtech,nas7820
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c07c3000 s6560 r8192 d13920 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/sda2 rootfstype=ext4 ubi.mtd=data,512
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 122948K/131072K available (4684K kernel code, 238K rwdata, 1524K rodata, 178K init, 239K bss, 8124K reserved
)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0618278 (6209 kB)
[ 0.000000] .init : 0xc0619000 - 0xc06459a0 ( 179 kB)
[ 0.000000] .data : 0xc0646000 - 0xc0681938 ( 239 kB)
[ 0.000000] .bss : 0xc0681938 - 0xc06bd87c ( 240 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:256
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.010000] Calibrating delay loop... 319.48 BogoMIPS (lpj=1597440)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.060000] CPU: Testing write buffer coherency: ok
[ 0.060000] Setting up static identity map for 0xc0473500 - 0xc047355c
[ 0.060000] CPU1: Booted secondary processor
[ 0.120000] Brought up 2 CPUs
[ 0.120000] SMP: Total of 2 processors activated (638.97 BogoMIPS).
[ 0.120000] devtmpfs: initialized
[ 0.120000] pinctrl core: initialized pinctrl subsystem
[ 0.120000] NET: Registered protocol family 16
[ 0.120000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.120000] gpio-oxnas 44000000.gpio: at address c884a000
[ 0.120000] gpio-oxnas 44100000.gpio: at address c884c000
[ 0.130000] pinctrl-oxnas pinctrl.5: initialized OX820 pinctrl driver
[ 0.130000] bio: create slab <bio-0> at 0
[ 0.240000] oxnas-pcie 47c00000.pcie-controller: PCIe version/deviceID 0x82510b5
[ 0.240000] oxnas-pcie 47c00000.pcie-controller: link up
[ 0.240000] oxnas-pcie 47c00000.pcie-controller: PCI host bridge to bus 0000:00
[ 0.240000] pci_bus 0000:00: root bus resource [mem 0x48000000-0x49ffffff]
[ 0.240000] pci_bus 0000:00: root bus resource [mem 0x4a000000-0x4bdfffff pref]
[ 0.240000] pci_bus 0000:00: root bus resource [io 0x4be00000-0x4befffff]
[ 0.240000] pci_bus 0000:00: root bus resource [bus 00-7f]
[ 0.240000] PCI: bus0: Fast back to back transfers disabled
[ 0.240000] pci 0000:00:00.0: BAR 0: assigned [mem 0x48000000-0x4800ffff 64bit]
[ 0.240000] vgaarb: loaded
[ 0.240000] SCSI subsystem initialized
[ 0.250000] usbcore: registered new interface driver usbfs
[ 0.250000] usbcore: registered new interface driver hub
[ 0.250000] usbcore: registered new device driver usb
[ 0.250000] pps_core: LinuxPPS API ver. 1 registered
[ 0.250000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.250000] PTP clock support registered
[ 0.250000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.250000] Switched to clocksource rps_clocksource_timer
[ 0.260000] NET: Registered protocol family 2
[ 0.260000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.260000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.260000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.260000] TCP: reno registered
[ 0.260000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.260000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.260000] NET: Registered protocol family 1
[ 0.260000] RPC: Registered named UNIX socket transport module.
[ 0.260000] RPC: Registered udp transport module.
[ 0.260000] RPC: Registered tcp transport module.
[ 0.260000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.270000] fuse init (API version 7.22)
[ 0.280000] msgmni has been set to 240
[ 0.280000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.280000] io scheduler noop registered
[ 0.280000] io scheduler deadline registered
[ 0.280000] io scheduler cfq registered (default)
[ 0.280000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.280000] 44200000.uart: ttyS0 at MMIO 0x44200000 (irq = 55) is a 16550A
[ 0.770000] console [ttyS0] enabled
[ 0.780000] loop: module loaded
[ 0.780000] scsi0 : sata_oxnas
[ 0.780000] ata1: SATA max UDMA/133 irq 50
[ 0.790000] ox820sata: reseting SATA core
[ 0.790000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size:
64
[ 0.790000] Scanning device for bad blocks
[ 0.910000] 2 ofpart partitions found on MTD device 41000000.nand
[ 0.910000] Creating 2 MTD partitions on "41000000.nand":
[ 0.920000] 0x000000000000-0x000000e00000 : "boot"
[ 0.930000] 0x000000e00000-0x000008000000 : "data"
[ 0.930000] stmmac - user ID: 0x12, Synopsys ID: 0x35
[ 0.940000] Ring mode enabled
[ 0.940000] DMA HW capability register supported
[ 0.950000] Enhanced/Alternate descriptors
[ 0.950000] Enabled extended descriptors
[ 0.950000] RX Checksum Offload Engine supported (type 2)
[ 0.960000] TX Checksum insertion supported
[ 0.960000] Wake-Up On Lan supported
[ 0.970000] Enable RX Mitigation via HW Watchdog Timer
[ 0.980000] libphy: stmmac: probed
[ 0.980000] eth0: PHY ID 001cc914 at 0 IRQ 0 (stmmac-0:00) active
[ 0.980000] eth0: PHY ID 001cc914 at 3 IRQ 0 (stmmac-0:03)
[ 0.990000] PCI: enabling device 0000:00:00.0 (0140 -> 0142)
[ 1.090000] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xc8880000, irq=51
[ 1.100000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.110000] ehci-pci: EHCI PCI platform driver
[ 1.110000] oxnas-ehci 40200100.ehci: EHCI Host Controller
[ 1.120000] oxnas-ehci 40200100.ehci: new USB bus registered, assigned bus number 1
[ 1.120000] oxnas-ehci 40200100.ehci: irq 39, io mem 0x40200100
[ 1.150000] oxnas-ehci 40200100.ehci: USB 2.0 started, EHCI 1.00
[ 1.150000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.160000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.170000] usb usb1: Product: EHCI Host Controller
[ 1.170000] usb usb1: Manufacturer: Linux 3.11.1+ ehci_hcd
[ 1.180000] usb usb1: SerialNumber: 40200100.ehci
[ 1.180000] hub 1-0:1.0: USB hub found
[ 1.180000] hub 1-0:1.0: 2 ports detected
[ 1.190000] usbcore: registered new interface driver usb-storage
[ 1.200000] usbcore: registered new interface driver usbserial
[ 1.200000] usbcore: registered new interface driver ch341
[ 1.210000] usbserial: USB Serial support registered for ch341-uart
[ 1.210000] usbcore: registered new interface driver pl2303
[ 1.220000] usbserial: USB Serial support registered for pl2303
[ 1.230000] mousedev: PS/2 mouse device common for all mice
[ 1.230000] usbcore: registered new interface driver usbhid
[ 1.240000] usbhid: USB HID core driver
[ 1.240000] TCP: cubic registered
[ 1.240000] NET: Registered protocol family 10
[ 1.250000] sit: IPv6 over IPv4 tunneling driver
[ 1.260000] NET: Registered protocol family 17
[ 1.260000] Bridge firewalling registered
[ 1.270000] VFP support v0.3: not present
[ 1.270000] UBI: attaching mtd1 to ubi0
[ 1.320000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.320000] ata1.00: ATA-6: ST3120827AS, 3.42, max UDMA/133
[ 1.330000] ata1.00: 234441648 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 1.340000] ata1.00: configured for UDMA/133
[ 1.340000] scsi 0:0:0:0: Direct-Access ATA ST3120827AS 3.42 PQ: 0 ANSI: 5
[ 1.350000] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 1.360000] sd 0:0:0:0: [sda] Write Protect is off
[ 1.360000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.380000] sda: sda1 sda2 sda3
[ 1.380000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.510000] usb 1-1: new high-speed USB device number 2 using oxnas-ehci
[ 1.620000] UBI: scanning is finished
[ 1.640000] UBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 9, need 20
[ 1.650000] UBI: attached mtd1 (name "data", size 114 MiB) to ubi0
[ 1.660000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 1.670000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 1.670000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[ 1.680000] UBI: good PEBs: 912, bad PEBs: 0, corrupted PEBs: 0
[ 1.680000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.680000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 1.680000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 1.680000] usb 1-1: Product: USB2.0 Hub
[ 1.710000] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[ 1.710000] hub 1-1:1.0: USB hub found
[ 1.720000] UBI: available PEBs: 0, total reserved PEBs: 912, PEBs reserved for bad PEB handling: 9
[ 1.720000] hub 1-1:1.0: 4 ports detected
[ 1.730000] UBI: background thread "ubi_bgt0d" started, PID 55
[ 1.810000] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.820000] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 1.850000] devtmpfs: mounted
[ 1.850000] Freeing unused kernel memory: 176K (c0619000 - c0645000)
[ 2.020000] usb 1-1.1: new high-speed USB device number 3 using oxnas-ehci
[ 2.130000] usb 1-1.1: New USB device found, idVendor=152d, idProduct=2338
[ 2.130000] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 2.140000] usb 1-1.1: Product: USB to ATA/ATAPI Bridge
[ 2.150000] usb 1-1.1: Manufacturer: JMicron
[ 2.150000] usb 1-1.1: SerialNumber: XXXXXXXXXXXXXXXXX
[ 2.160000] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 2.160000] scsi1 : usb-storage 1-1.1:1.0
[ 2.250000] usb 1-1.3: new full-speed USB device number 4 using oxnas-ehci
[ 2.360000] usb 1-1.3: New USB device found, idVendor=067b, idProduct=2303
[ 2.360000] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.370000] usb 1-1.3: Product: USB-Serial Controller
[ 2.380000] usb 1-1.3: Manufacturer: Prolific Technology Inc.
[ 2.380000] pl2303 1-1.3:1.0: pl2303 converter detected
[ 2.390000] usb 1-1.3: pl2303 converter now attached to ttyUSB0
[ 2.560000] systemd[1]: systemd 207 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT
+ACL +XZ)
Welcome to Arch Linux ARM!
[ 2.600000] systemd[1]: Set hostname to <nas>.
[ 2.720000] systemd-gpt-auto-generator[65]: Failed to verify GPT partition /dev/block/8:2: No such file or directory
[ 2.740000] systemd[1]: /usr/lib/systemd/system-generators/systemd-gpt-auto-generator exited with exit status 1.
[ 3.140000] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 3.150000] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 3.150000] systemd[1]: Expecting device dev-ttyS0.device...
Expecting device dev-ttyS0.device...
[ 3.170000] scsi 1:0:0:0: Direct-Access ST960821 A PQ: 0 ANSI: 2 CCS
[ 3.180000] systemd[1]: Expecting device sys-subsystem-net-devices-wlp0s0.device...
Expecting device[ 3.180000] sd 1:0:0:0: [sdb] 117231408 512-byte logical blocks: (60.0 GB/55.8 GiB)
sys-subsystem-n[ 3.190000] sd 1:0:0:0: [sdb] Write Protect is off
et-devices-wlp0s[ 3.200000] sd 1:0:0:0: [sdb] Asking for cache data failed
0.device...
[ 3.210000] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3.220000] sd 1:0:0:0: [sdb] Asking for cache data failed
[ 3.220000] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3.240000] systemd[1]: Expecting device sys-subsystem-net-devices-eth0.device...
Expecting device sys-subsystem-net-devices-eth0.device...
[ 3.270000] systemd[1]: Starting Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 3.290000] systemd[1]: Reached target Remote File Systems.
[ 3.290000] systemd[1]: Starting LVM2 metadata daemon socket.
[ OK ] Listening on LVM2 metadata daemon socket.
[ 3.320000] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 3.320000] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 3.350000] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 3.350000] systemd[1]: Starting Delayed Shutdown Socket.
[ OK ] Listening on Delayed Shutdown Socket.
[ 3.380000] systemd[1]: Listening on Delayed Shutdown Socket.
[ 3.380000] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ OK ] Listening on Device-mapper event daemon FIFOs.
[ 3.410000] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 3.410000] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ OK ] Set up automount Arbitrary Executable File Formats F...utomount Point.
[ 3.450000] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 3.450000] systemd[1]: Starting Encrypted Volumes.
[ OK ] Reached target Encrypted Volumes.
[ 3.480000] systemd[1]: Reached target Encrypted Volumes.
[ 3.480000] systemd[1]: Starting Journal Socket.
[ OK ] Listening on Journal Socket.
[ 3.500000] sdb: sdb1 sdb2 sdb3 sdb4
[ 3.500000] sd 1:0:0:0: [sdb] Asking for cache data failed
[ 3.510000] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 3.520000] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 3.520000] systemd[1]: Listening on Journal Socket.
[ 3.530000] systemd[1]: Started Load Kernel Modules.
[ 3.550000] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 3.580000] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 3.600000] systemd[1]: Mounting FUSE Control File System...
Mounting FUSE Control File System...
[ 3.630000] systemd[1]: Starting Setup Virtual Console...
Starting Setup Virtual Console...
[ 3.660000] systemd[1]: Mounted Huge Pages File System.
[ 3.660000] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ OK ] Started Journal Service.
[ 3.710000] systemd[1]: Started Journal Service.
[ OK ] Listening on udev Kernel Socket.
[ OK ] Listening on udev Control Socket.
Starting udev Coldplug all Devices...
Starting Create list of required static device nodes...rrent kernel...
[ OK ] Reached target Paths.
[ 3.880000] systemd-journald[77]: Vacuuming done, freed 0 bytes
Mounting Debug File System...
Mounting Temporary Directory...
Starting File System Check on Root Device...
Expecting device dev-sda1.device...
[ OK ] Created slice Root Slice.
[ OK ] Created slice User and Session Slice.
[ OK ] Created slice System Slice.
[ OK ] Created slice system-netctl.slice.
[ OK ] Created slice system-getty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Reached target Slices.
[ OK ] Started Apply Kernel Variables.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted FUSE Control File System.
[ OK ] Started Setup Virtual Console.
[ OK ] Mounted Debug File System.
[ OK ] Mounted Temporary Directory.
[ OK ] Started Create list of required static device nodes ...current kernel.
Starting Create static device nodes in /dev...
[ OK ] Started udev Coldplug all Devices.
systemd-fsck[88]: linux: clean, 89858/6553600 files, 1093520/26206210 blocks
[ OK ] Started File System Check on Root Device.
Starting Remount Root and Kernel File Systems...
[ OK ] Started Create static device nodes in /dev.
Starting udev Ke[ 4.600000] EXT4-fs (sda2): re-mounted. Opts: (null)
rnel Device Manager...
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Reached target Local File Systems (Pre).
[ 4.670000] systemd-udevd[103]: starting version 207
Activating swap /swapfile...
Starting Load/Save Random Seed...
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started Load/Save Random Seed.
[ OK ] Found device /dev/ttyS0.
[ OK ] Found device /sys/subsystem/net/devices/eth0.
[ 5.390000] systemd-udevd[113]: renamed network interface wlan0 to wlp0s0
[ OK ] Found device AR9287 Wireless Network Adapter (PCI-Express).
[ 6.150000] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ OK ] Found device ST3120827AS.
Mounting /boot...
[ OK ] Mounted /boot.
[ OK ] Reached target Local File Systems.
Starting Recreate Volatile Files and Directories...
Starting Trigger Flushing of Journal to Persistent Storage...
[ OK ] Started Recreate Volatile Files and Directories.
Starting Update [ 6.440000] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
UTMP about System Reboot/Shutdown...
[ 6.490000] systemd-journald[77]: Received request to flush runtime journal from PID 1
[ OK ] Started Trigger Flushing of Journal to Persistent Storage.
[ OK ] Started Update UTMP about System Reboot/Shutdown.
[ 7.340000] Adding 1048572k swap on /swapfile. Priority:-1 extents:2 across:1155068k
[ OK ] Activated swap /swapfile.
[ OK ] Reached target Swap.
[ OK ] Reached target System Initialization.
[ OK ] Listening on SWAT Samba Web Admin Tool.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ 8.170000] EXT4-fs (sdb3): mounting ext3 file system using the ext4 subsystem
[ 8.280000] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null)
[ 8.310000] EXT4-fs (sdb2): mounting ext2 file system using the ext4 subsystem
[ 8.410000] EXT4-fs (sdb2): mounted filesystem without journal. Opts: (null)
[ OK ] Reached target Sockets.
[ OK ] Reached target Timers.
[ OK ] Reached target Basic System.
Starting A basic dhcp ethernet connection...
Starting Automatically generated profile by wifi-menu...
Starting D-Bus System Message Bus...
[ OK ] Started D-Bus System Message Bus.
Starting Login Service...
Starting Permit User Sessions...
[ OK ] Started Permit User Sessions.
Starting Getty on tty1...
[ OK ] Started Getty on tty1.
Starting Serial Getty on ttyS0...
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Reached target Login Prompts.
[ OK ] Started Login Service.
[ 10.390000] eth0: device MAC address XXXXXXXXXXXX
[ 10.850000] IPv6: ADDRCONF(NETDEV_UP): wlp0s0: link is not ready
[ 11.900000] wlp0s0: authenticate with XXXXXXXXXXXXXXXXX
[ 11.920000] wlp0s0: send auth to XXXXXXXXXXXXXX (try 1/3)
[ 11.930000] wlp0s0: authenticated
[ 11.950000] wlp0s0: associate with XXXXXXXXXX (try 1/3)
[ 11.950000] wlp0s0: RX AssocResp from XXXXXXXXXXX (capab=0x411 status=0 aid=3)
[ 11.960000] wlp0s0: associated
[ 11.970000] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s0: link becomes ready
[ 12.390000] libphy: stmmac-0:00 - Link is Up - 100/Full
[ OK ] Started Automatically generated profile by wifi-menu.
Arch Linux 3.11.1+ (ttyS0)
nas login:
')