by JohnH » Mon Feb 21, 2011 7:38 pm
$this->bbcode_second_pass_quote('squeezeplug', '
')Here is the output from netconsole (kernel):
$this->bbcode_second_pass_code('', 'Linux version 2.6.36-ubit-01575-gd36fea8 (root@vmdebian-cli) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #1 Fri Dec 17 17:43:50 GMT 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Seagate GoFlex Net
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(pogoplug),-(root) root=/dev/sda1 rootdelay=10 netconsole=@10.10.10.6/eth0,@10.10.10.4/
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 118848k/118848k available, 12224k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc8800000 - 0xfe800000 ( 864 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc002e000 ( 152 kB)
.text : 0xc002e000 - 0xc052a000 (5104 kB)
.data : 0xc0550000 - 0xc0585880 ( 215 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:114
Console: colour dummy device 80x30
Calibrating delay loop... 1192.75 BogoMIPS (lpj=5963776)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A1, TCLK=200000000.
Feroceon L2: Cache support initialised.
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 4624K
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
aufs 2.1-36
msgmni has been set to 241
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 21
ata2: SATA max UDMA/133 irq 21
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 513 at 0x000004020000
4 cmdlinepart partitions found on MTD device orion_nand
Creating 4 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000500000 : "uImage"
0x000000500000-0x000002500000 : "pogoplug"
0x000002500000-0x000010000000 : "root"
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:10:75:26:3d:4e
netconsole: local port 6665
netconsole: local IP 10.10.10.6
netconsole: interface 'eth0'
netconsole: remote port 6666
netconsole: remote IP 10.10.10.4
netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
netconsole: device eth0 not up yet, forcing it
ata1: SATA link down (SStatus 0 SControl F300)
ata2: SATA link down (SStatus 0 SControl F300)
eth0: link up, 1000 Mb/s, full duplex, flow control disabled
console [netcon0] enabled
netconsole: network logging started
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
usb 1-1: new high speed USB device using orion-ehci and address 2
scsi2 : usb-storage 1-1:1.0
rtc-mv rtc-mv: internal RTC not ticking
i2c /dev entries driver
cpuidle: using governor ladder
cpuidle: using governor menu
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
oprofile: hardware counters not available
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
registered taskstats version 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing init memory: 152K
scsi 2:0:0:0: Direct-Access Kingston DataTraveler 410 1.00 PQ: 0 ANSI: 2
sd 2:0:0:0: [sda] 7571944 512-byte logical blocks: (3.87 GB/3.61 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2 sda3
sda: p3 size 6273024 extends beyond EOD, enabling native capacity
sd 2:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2 sda3
sda: p3 size 6273024 extends beyond EOD, truncated
sd 2:0:0:0: [sda] Assuming drive cache: write through
sd 2:0:0:0: [sda] Attached SCSI removable disk')
Anyone an idea what's going wrong here?
Looking at the kernel-output, it reminds very much of what tomcheng76 experienced in this
viewtopic.php?f=18&t=494&start=10#p3467It stops at the same place. Also without ssh. The question is what he did to get it to work?