PogoPlug boot problem

[timmypro]

I have a Pogoplug E02. I mess around with uboot with fw_setenv and it does not boot up anymore. (no response to SSH, no status light on the device, IP assigned to pogoplug) I could netconsole to it and it shows the following when i reboot.
$this->bbcode_second_pass_code('', 'U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
u-boot>>')

fw_printenv output:

$this->bbcode_second_pass_code('', 'Pogoplug:ß$ /usr/sbin/fw_printenv
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 öö ext2load usb 0:1 0x1700000 /rescueme 1 öö fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_device=0:1
usb_root=/dev/sda1
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
ethaddr=00:25:31:03:04:9C
arcNumber=2097
serverip=192.168.0.102
ipaddr=192.168.0.103
if_netconsole=ping $serverip
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
preboot=run if_netconsole start_netconsole
usb_rootfstype=ext3
usb_init=usb stop; usb start; run usb_scan
bootcmd=usb=start')

I tried to type some command like start usb but no response. I dont have serial cable. Any thought of how to fix it?

[moonman]

You've messed up bootcmd and your arcnumber is wrong.

Within netconsole:
$this->bbcode_second_pass_code('', 'setenv arcNumber '3542'
setenv machid 'dd6'
setenv bootcmd 'usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset'
saveenv
reset')

If this doesn't help, then show netconsole output without interrupting it.

[timmypro]

Thanks for your quick reply. After using the settings u mentioned. I am able to SSH into it. The green light is on now. I probably need some time to find out the meaning of each parameters. Here is the netconsole output.
$this->bbcode_second_pass_code('', 'lubuntu@lubuntu:~$ nc -l -u -p 6666 &
[1] 4312
lubuntu@lubuntu:~$ nc -u 192.168.0.103 6666

U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
stopping USB..
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ........ done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...
')

I think the device is looking for boot device and it was not there. Any thought?

Before I messed up the settings. I used instruction from http://archlinuxarm.org/platforms/armv5 ... 2-pinkgray to make a boot image on usb disk but it didn't bootup. so I start to explore fw_setenv and see if it can solve the problem. That's how i messed up the settings.

[moonman]

Yes, does not see any USB storage devices. Is it a USB flash drive? Try a different one and use the instructions linked in my signature. Don't change anything in U-Boot environment!

[timmypro]

$this->bbcode_second_pass_quote('moonman', 'Y')es, does not see any USB storage devices. Is it a USB flash drive? Try a different one and use the instructions linked in my signature. Don't change anything in U-Boot environment!

[moonman]

You did "sudo su" prior to extracting ? This is important to get the permissions right. Also, according to your U-Boot environemnt your rootfs partition needs to be ext3. For U-Boot it does not matter if the partition boot flag is set, what is important though is that rootfs partition is first on the hard drive, and is a primary partition.

[timmypro]

$this->bbcode_second_pass_quote('moonman', 'Y')ou did "sudo su" prior to extracting ? This is important to get the permissions right. Also, according to your U-Boot environemnt your rootfs partition needs to be ext3. For U-Boot it does not matter if the partition boot flag is set, what is important though is that rootfs partition is first on the hard drive, and is a primary partition.