Followed original manual, but E02 won't boot with archlinux

[fox1986]

Hi. I bought a Pogoplug v2 E02 and followed the manual at http://archlinuxarm.org/platforms/armv5 ... s-ui-tabs2 to install archlinux on my Pogoplug. I have a USB 4GB Flash Stick attached to the front usb of the pogoplug and followed all the steps accurately. There were no error during installation.

However when i reebot, the connection is closed. If I try to connect as root with SSH, it says that password "root" is wrong. It only works with the default Pogoplug passwort "ceadmin". Once I am connected via SSH. I have a shell saying "Pogoplug>" but no archlinux has booted up. What do I wrong? I already tried that "start-stop-start" Trick and PRE_UP='sleep 15' but still no succes.


$this->bbcode_second_pass_code('', '
Pogoplug:/usr/sbin$ ./fw_printenv
ethact=egiga0
bootdelay=3
baudrate=115200
mainlineLinux=yes
console=ttyS0,115200
led_init=green blinking
led_exit=green off
led_error=orange blinking
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
mtdids=nand0=orion_nand
partition=nand0,2
stdin=serial
stdout=serial
stderr=serial
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_list=1 2 3 4
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_init=run usb_scan
usb_device=0:1
usb_root=/dev/sda1
usb_rootdelay=10
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
ethaddr=00:25:31:04:95:23
arcNumber=2097
usb_rootfstype=ext3
bootcmd=usb start; usb stop; usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
')

[WarheadsSE]

Get netconsole working, per the advanced tab of the instructions. The output of that will help us debug.

[fox1986]

I got everything to work, even Samba. But then I was stupid enough to follow the static-ip guide. It worked fine till I pulled the power plug and reboot the Pogoplug again. For some reason it doesnt use the static-ip adress anymore who worked fine before reboot and i cant acces via the new ip.

Is my pogoplug bricked now?

[pepedog]

No
viewtopic.php?f=18&t=3312&p=19207#p19207
Then try again using netctl https://wiki.archlinux.org/index.php/Netctl
Copy example and modify.
Don't forget to remove netcfg service

[WarheadsSE]

And shut it down before yanking the power.