Goflex net : Unable to boot after halt.

[hamal]

I sucessfully install arch linux on my goflex net.
after the first reboot, I update the whole system and reboot again.
Everything seems fine.
I try to mount some devices and install some package.
then, I decide to shutdown my goflex net by "halt" command.
I unplug the power when the led is off.

And it won't boot anymore.
LED on my flash drive flashs once.
the front green led on goflex net is always flashing.

netcat doesn't work. (empty output)
wireshark : (only one line)
==============
1 0.000000 02:50:43:bb:ca:78 Broadcast ARP 60 Who has 10.10.10.5? Tell 10.10.10.6
==============

the mac address '02:50:43:bb:ca:78' is different from the mac on the label on goflex net.

[hamal]

I purchased an usb to serial adapter and I got some result.

$this->bbcode_second_pass_code('', '
U-Boot 2010.09 (Feb 16 2011 - 18:42:02)
UBIT v0.6 by Jeff Doozan and Peter Carmichael

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:silent", error -19
Error reading superblock on volume 'ubi:silent'!
UBIFS not mounted, use ubifs mount to mount volume first!
Using egiga0 device
ping failed; host 10.10.10.5 is not alive
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
1 Storage Device(s) found
Hit any key to stop autoboot: 0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:fast", error -19
Error reading superblock on volume 'ubi:fast'!
UBIFS not mounted, use ubifs mount to mount volume first!
** Bad partition 1 **
** Bad partition 1 **
Device NOT ready
Request Sense returned 00 00 00
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
')


I re-format my usb stick and extract ALARM onto it.
but my goflex net still won't boot.

$this->bbcode_second_pass_code('', '
U-Boot 2010.09 (Feb 16 2011 - 18:42:02)
UBIT v0.6 by Jeff Doozan and Peter Carmichael

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:silent", error -19
Error reading superblock on volume 'ubi:silent'!
UBIFS not mounted, use ubifs mount to mount volume first!
Using egiga0 device
ping failed; host 10.10.10.5 is not alive
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:fast", error -19
Error reading superblock on volume 'ubi:fast'!
UBIFS not mounted, use ubifs mount to mount volume first!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
** ext2fs_devread() read error - block
** Unable to read "/boot/uImage" from usb 0:1 **
Device NOT ready
Request Sense returned 19 00 2B
** Can't read partition table on 0:0 **
** Bad partition 1 **
Device NOT ready
Request Sense returned 19 00 2B
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
Device NOT ready
Request Sense returned 19 00 2B
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
** Block device usb 1 not supported
** Block device usb 1 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 2 not supported
** Block device usb 2 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 3 not supported
** Block device usb 3 not supported

** Invalid boot device **

** Invalid boot device **

Reset IDE: Bus 0: not available Bus 1: not available
** Bad partition 1 **
** Bad partition 1 **
No Powersaving mode 7F
Error (no IRQ) dev 0 blk 0: status 0x7f
** Can't read from device 0 **

** Unable to use ide 0:1 for fatload **
No Powersaving mode 7F
Error (no IRQ) dev 0 blk 0: status 0x7f
** Can't read from device 0 **

** Unable to use ide 0:1 for fatload **
** Bad partition 1 **
** Bad partition 1 **
No Powersaving mode 7F
Error (no IRQ) dev 1 blk 0: status 0x7f
** Can't read from device 1 **

** Unable to use ide 1:1 for fatload **
No Powersaving mode 7F
Error (no IRQ) dev 1 blk 0: status 0x7f
** Can't read from device 1 **

** Unable to use ide 1:1 for fatload **
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:ramdisk", error -19
Error reading superblock on volume 'ubi:ramdisk'!
UBIFS not mounted, use ubifs mount to mount volume first!
Marvell>>
')

[Kurlon]

uboot is complaining that it can't read the file system on that stick. It only supports FAT (don't use that) or ext2 / ext3.

[hamal]

I am sure that I use ext2.
I tried another usb stick without success.

$this->bbcode_second_pass_code('', '(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... Device NOT ready
Request Sense returned 00 00 00
1 Storage Device(s) found
Hit any key to stop autoboot: 0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:fast", error -19
Error reading superblock on volume 'ubi:fast'!
UBIFS not mounted, use ubifs mount to mount volume first!
** Bad partition 1 **
** Bad partition 1 **
Device NOT ready
Request Sense returned 00 00 00
** Can't read from device 0 **
')

[hamal]

Try to boot from sata.

$this->bbcode_second_pass_code('', '
U-Boot 2010.09 (Feb 16 2011 - 18:42:02)
UBIT v0.6 by Jeff Doozan and Peter Carmichael

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:silent", error -19
Error reading superblock on volume 'ubi:silent'!
UBIFS not mounted, use ubifs mount to mount volume first!
Using egiga0 device
ping failed; host 10.10.10.5 is not alive
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:fast", error -19
Error reading superblock on volume 'ubi:fast'!
UBIFS not mounted, use ubifs mount to mount volume first!
** Block device usb 0 not supported
** Block device usb 0 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 1 not supported
** Block device usb 1 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 2 not supported
** Block device usb 2 not supported

** Invalid boot device **

** Invalid boot device **
** Block device usb 3 not supported
** Block device usb 3 not supported

** Invalid boot device **

** Invalid boot device **

Reset IDE: Bus 0: OK Bus 1: not available
Device 0: Model: Hitachi HTS547575A9E384 Firm: JE4OA60A Ser#: J2540054GK2Y6E
Type: Hard Disk
Supports 48-bit addressing
Capacity: 715404.8 MB = 698.6 GB (1465149168 x 512)
Loading file "/boot/uImage" from ide device 0:1 (hda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 0:1 **
Loading file "/uInitrd" from ide device 0:1 (hda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - ide 0:1 **
reading /boot/uImage

** Unable to read "/boot/uImage" from ide 0:1 **
reading /uInitrd

** Unable to read "/uInitrd" from ide 0:1 **
** Bad partition 1 **
** Bad partition 1 **
No Powersaving mode 7F
Error (no IRQ) dev 1 blk 0: status 0x7f
** Can't read from device 1 **

** Unable to use ide 1:1 for fatload **
No Powersaving mode 7F
Error (no IRQ) dev 1 blk 0: status 0x7f
** Can't read from device 1 **

** Unable to use ide 1:1 for fatload **
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:ramdisk", error -19
Error reading superblock on volume 'ubi:ramdisk'!
UBIFS not mounted, use ubifs mount to mount volume first!
Marvell>>
')

It seems that uboot is broken and thus unable to read from ext2/ext3 partition.