Can't boot latest Cubox image

[azergty00]

$this->bbcode_second_pass_quote('ykmag', 'T')here seems to be a problem with lastes cubox build. I have followed the instructions and copied boot.scr.mmcblk0p1 to boot.scr

From the boot:
$this->bbcode_second_pass_code('', '===> Executing ext2load mmc 0:1 0x02000000 /boot.scr
Loading file "/boot.scr" from mmc device 0:1 (mmcda1)
** File not found /boot.scr
===> Executing fatload mmc 0:1 0x02000000 /boot.scr
reading /boot.scr

** Unable to read "/boot.scr" from mmc 0:1 **
===> Executing ext2load mmc 0:1 0x02000000 /boot/boot.scr
Loading file "/boot/boot.scr" from mmc device 0:1 (mmcda1)
456 bytes read
## Executing script at 02000000
======== Setting bootargs ========
======== Loading kernel ========
Loading file "/boot/uImage" from mmc device 0:1 (mmcda1)
undefined instruction
pc : [<f0000002>] lr : [<00635d9c>]
sp : 005ff570 ip : 00000001 fp : a9a8cfec
r10: 04ea6a73 r9 : c8d3566e r8 : 005fffcc
r7 : 1d3509e8 r6 : a9a8b5d4 r5 : 0e94d52f r4 : fd7d5fb5
r3 : ffffffff r2 : 00000001 r1 : 000f4240 r0 : 00000000
Flags: nZcv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
')

Anyone have an idea?

[pepedog]

I will make new rootfs for testing. If that fails on micro sd then it might be other things similar to what happens on a raspberry pi.
Don't have large sd card here, but all ok on sandisk USB and a sata

[azergty00]

I forgot to precise my Uboot version :
U-Boot 2009.08 (Jan 15 2012 - 00:43:32) Marvell version: 5.4.4 NQ

It can be useful thanks anyway

[pepedog]

Just checking, do you have the new 2Gb pro version?
There is a later uboot, the image should work on the old though. Don't ugrade a pro via installer method.

[ykmag]

Sorry for late replay.
I am not sure wich version I have, Is there any way I can tell?

[pepedog]

With the serial connected, interupt uboot
Does it mention SR1 ?

[ykmag]

The ouput from boot:
$this->bbcode_second_pass_code('', 'U-Boot 2009.08 (Jan 15 2012 - 00:43:32) Marvell version: 5.4.4 NQ

BootROM:
Version on chip: 2.33
Status: OK
Retries #: 0
Board: CuBox
SoC: 88AP510 (A1)
CPU: Marvell Sheeva (Rev 5)
CPU @ 800Mhz, L2 @ 400Mhz
DDR3 @ 400Mhz, TClock @ 166Mhz
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
DRAM: 1 GB
CS 0: base 0x00000000 size 512 MB
CS 1: base 0x20000000 size 512 MB
Addresses 12M - 0M are saved for the U-Boot usage.
SF: Detected M25P32 with page size 64 kB, total 4 MB

Streaming disabled
L2 Cache Prefetch disabled
L2 Cache ECC disabled
Modifying CPU/CORE/DDR power rails to 1.0(-2.5%) / 1.0(-5%) / 1.5(-5%)
USB 0: Host Mode
USB 1: Host Mode
Setting VPU power OFF.
Setting GPU power ON.
MMC: MV_SDHCI: 0, MV_SDHCI: 1
')

Since there is 1G ram it's not Pro, I guess

[pepedog]

You got the older uboot, you can upgrade here
http://www.solid-run.com/mw/index.php/CuBox_Installer
It should still boot, have you said how drive is formatted? ext3 is best

[ykmag]

Tried both ext2 and ext3, now it is ext3.

[ykmag]

New u-boot installed, nothing changed for the better...